anycubic photon m3 fep 3d models

... the center of the cover to act as a handle for easier removal. The tolerances are tight, but you can place the cover on the vat and remove it without needing to remove the resin vat from the printer itself. This fits the original anycubic photon.

This is a custom-made adapter designed for using a 92mm fan in place of the rear panel on an Anycubic Photon 3D Printer. The main purpose of this adapter is to install an activated carbon filter element that draws fumes out of the printer through the...

... one of these parts, which includes STL files for both right and left sides. I installed them on both sides of my lid (it looks better that way), replacing one of the hinge screws with M3 x 15mm ones I had on hand, along with washers and Nylock Nuts.

I just bought an ANYCUBIC Wash and Cure Station and noticed that the buildplate Adapter is only for the old ANYCUBIC Photon. ...So I created an adapter fpr the ANYCUBIC Photon Mono.

Another Version of the Genius “ANYCUBIC PHOTON Easy Leveler” by Wundel https://www.thingiverse.com/thing:3096818 In this Review, Only Two Improvements Are Made - Pressure Springs and Insert Positioning The only improvements made to this design are...

**https://www.printables.com/model/643200-anycubic-photon-mono-2-vat-cover** Made a vat cover/lid for the new *Photon Mono 2* since i couldn't find one. Enjoy. There are two models: one titled **VASE** and one titled **RIGID**. The **RIGID**...

Adapter for Photon Mono buildplate to mount on Anycubic Wash & Cure Station. Uses M6 screws, like the original. I used a height of 15mm instead of 12mm of the original mount on the Photon Mono. It makes everything a bit more stable and for me...

Another version of the great “ANYCUBIC PHOTON Easy Leveler” by wundel https://www.thingiverse.com/thing:3096818. In this review, only two improvements are notable - pressure springs have been included to avoid holding the plate in place with your...

I am creating two versions of my rear vent duct adapters for the Anycubic Photon: a 4" version for connecting to standard ventilation tubing and a 2.5" version for connecting to vacuum hoses and smaller tubing. To install, follow the instructions on...

I wanted to give it a more personalized feel to this cover so I added the Photon and the Anycubic logo to it. Please notice that the area where the big logo is located is very thin and some might assume is not full uv-proof. I am fine with mine....

This is a z limit spacer for the Anycubic Photon Zero. It allows you to raise the height at which your z limit triggers for the Wham Bam FBS bed. This replaces the current metal bracket that blocks the sensor. The only difference between this and...

An Anycubic Photon vat holder is designed specifically to drain resin back into the bottle. The center of the vat should sit directly in the middle of a 1-liter bottle, with the bottle pushed up against the Skadis pegboard. A unique attachment on the...

This is my own try to make the vat for Anycubic Photon Mono X, since I wanted to make a drain stand for the Vat. I dont claim that it is totally exact as the original but as close as possible I could make it. If anyone finds anything wrong with it...

... together using superglue (CA Glue). This design enables the use of screws that already hold the vent-plate on the back of the Anycubic Photon. ...The full un-split version is included, along with the Solidworks source file for further modification.

Center this within the slicer for your Anycubic Photon, and then print it. Count the ridges on the sides. There should be exactly ten of them. The ridges are a precise 0.25mm wide and 0.5mm apart. For each one missing, you're losing a significant...

This accessory, designed to replace the upper glass of the Anycubic photon printer, will draw in part of the odor emitted by the resin during printing and, with a rubber tube properly connected, discharge it outside. For example, allowing the tube to...

It's compatible with Epax-X1 and Anycubic photon vats, possibly other models as well. I built this using 10mm aluminum pipe for the legs and 8mm pipe for the rotating pins, which I happened to have on hand. The funnel holder is made from M5 screws,...

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

This is a minimal extruding replacement for the back vent plate of the Anycubic Photon Mono SE 3D SLP printer with a 4" vent that can be used with a 4" Inch Inline Fan to vent the fumes. NOTE: This item hasn't been printed or tested yet, but the...

This is the DIY carbon filter for Anycubic Photon Mono SE. It should reduce some resin fumes.The factory carbon filtration of Photon Mono SE doesn't work quite well. Two fans push fumes from build area through the activated carbon sponge to the...

I liked IKE_144's remix of Ermai's build plate holder that makes it so you can angle your Anycubic Photon (or Qidi Shadow 5.5s in my case) build plate over the vat to help with dripping from different angles. My printer doesn't do bridges very...

Here is the link I used for the Thingiverse Files I used : - http://www.thingiverse.com/thing:3419926 Thanks to Corona688 Enjoy Parts Needed I just removed two of the original M3 screws and replaced them with longer ones. ... P.s Check out my Other...

@DocTanner crafted an innovative Rear Vent duct adapter for the Anycubic Photon, available here: https://www.myminifactory.com/object/3d-print-64661. I sought to enhance this design by adding a feature that would allow me to incorporate filters...

Hi!I made this for my Anycubic Photon Mono SE. This is the 4th iteration and can be printed at very high speed and still be functional.&nbsp;</p><p>Settings I used:<br>Line Width: 0.6mm<br>Layer Height: 0.28mm<br>Speed: 120mm/s<br>Material:...

This is designed for straining and collecting debris from anycubic photon vat systems. It can be particularly frustrating to go through the straining process after encountering failed prints, especially when the hardened resin is not visible at all...

Based on a bad experience I had, I have created this protection bar for the Anycubic Photon Mono X Axis. I had an accident where I spilled resin, and it ran down the central axis and jammed the stepper motor. I thought it was damaged because it...

My Anycubic Photon S has 2 exhaust fans in the rear of the build chamber. These exhaust fans have housings on top of them with small bags of activated carbon inside. This filter box is simply a container with holes in the bottom that are small enough...

I made this little adapter so that I could use my Anycubic Photon build plate with the Elegoo Mercury Plus. It is a small quick design that can be quickly printer and used. It is designed to reuse the main bracket hardware that comes with Mercury...

This device is designed to be attached to the Anycubic Photon, specifically aimed at reducing the smell from resin use.\r\nA brushless fan with an 80mm diameter should be installed between the panel and the box, secured in place using m5...

SHOULD WORK WITH ANYCUBIC PHOTON S BUT HAS NOT BEEN TESTED FOR IT! ... INSTALLATION: 1) Unscrew the two screw under the plate mount in the front right corner 2) Insert the spacer between the metal plate and the plate mount 3) Retighten the two...