anycubic photon heater 3d models

The new lid from KayIOA didn't fit properly on my newly purchased vat. Check out the picture of the original vat (on the left) and the updated one (on the right). The smaller spout made it impossible for the lid to sit flush on top of the vat. To...

A small shield for my second resin tank when it's not in use. ...As a lid, I employ the Thingiverse design 582131.

I created this using Fusion 360, a great little spot for the versatile spatula to reside. The draining system might not be perfect, but it functions and is definitely an improvement over having the resin-covered spatula cluttering up the desk. A...

Ice scraper

A simple tool to extract even the last drops of resin. Just add the four M3 screws to secure its position and you're good to go. Disclaimer 1: I am not sure whether the last drops are clean enough to be used for printing. Disclaimer 2: Make sure to...

Extension for the homing bar to allow for a magnetic base.

Diesen Abstandshalter habe ich konstruiert, nachdem ich meine "flexible Buildplate" montiert habe und Probeme hatte, den Nullpunkt zu justieren. Durch dieses Zwischenstück wird der Zero-Sensor etwas früher erreicht, es gehen aber ca 5mm an Bauhöhe...

With these shields in place, I'm confident that I can safely leave the resin inside the printer for an extended period without worrying about exposure to light. ...The 16 magnets I've employed have a 18mm diameter and 5mm height, but interestingly, the...

This filter tower can be easily attached to the interior fan without any change. Add an active carbon filter. ...I recommend to remove the filter below the fan.

Кронштейн для слива смолы с детали и стола после завершения печати. ...Наклоняет стол на 30 градусов, что позволяет стечь остаткам смолы

This design consists of 2 pieces which will be blended together when printed. 1. Import the files and insure that they are completly aligned 2. Turn one of the pieces off and slice individually (Make sure to Z-retract of at least 2.5mm. Do not...

I designed this using Fusion 360, it's a neat little place for that useful spatula to be. the draining system may not be the best one, but it works, and it's certanly better than having the resin covered spatula over the desk. A small, nice looking...

I'm installing a ventilation system to clear out the stinky air from my space. ...The tube is connected to an exhaust hose that leads directly outside, drawing fresh air in and pushing stale odors out.

This is a guide for the build plate to properly square before locking it tight during Z calibration. Not all machine are the same set up, Guide may need some length adjustment. ...Please do modify if needed.

Create parts for the 0815Paulchen at https://www.thingiverse.com/thing:3013054. The creation fits perfectly into a standard installation or insulation tube (flexible, outer diameter: 25mm, inner diameter 17.9mm). ... The airguide's outer diameter is...

You can store the UV resin you're not using in these caps, which will protect it from light and dust by placing it in a tank container. ...By printing the two caps in PLA, you can use the bottom one to preserve the FEP.

After viewing a similar design, which required an external inline fan which I felt was too expensive and bulky, I designed this model. The original idea came from Doc Tanner at https://www.thingiverse.com/thing:2877754 if you want to checkout his. ...

I Need a Plate Support for My Magnetic Stirrer Container

Spacer for the Z Limit switch on the AnyCubic Photon S when using the WhamBam Flex Plate system

Cover for Anycubic Photon Mono VAT to protect resin from UV, should be compatible with Elegoo Mars PRO Enjoy !

Spacer for the Z Limit switch on the AnyCubic Photon S when using the WhamBam Flex Plate system

... on Thingiverse. Click this link to become part of the Photon Army: https://www.thingiverse.com/groups/anycubic-photon Watch this video for step-by-step instructions on how to clean your resin vat after printing: https://youtu.be/-9aPhhMv4ww

Anycubic Photon S Drip Hanger Pro instead of an axis in the loops, you can put a piece of filament and glue it with glue

Anycubic Photon Side Panel 4-Inch Extraction Tube Adapter. ...The diameter has been upgraded to 9.6 inches for a more precise fit.

I upgraded my Anycubic Photon Mono SE with Solvo magnetic buildplate. ...So i needed this spacer to save my screen from crashing.

I neded a holder for all the tools of my 3D printers (Anycubic predator, photon zero). So I designed one in Fusion360. ... Feel free to use.

A low profile angled fan mount for the rear of the Anycubic Photon S. ...Allows mounting a 120mm fan and wire passthrough.

Cover scratch protection for Photon Mono X from Anycubic 404 error still exist after reuploading. ... Try to download each file from "Thing Files"

I modified the original vat holder to accommodate the Anycubic Photon Mono X. ... Fit's nicely and does what it was designed to do.