anycubic photon cleaning 3d models

All parts print effortlessly on Anycubic photon. Due to slight variations in fan sizes, some filing of the inside of the fan box components may be necessary. I used Gorilla tape to ensure fans were securely sealed since exhaust ventilation occurs...

This system extracts fumes from an Anycubic Photon printer without replacing existing panels. Instead, it attaches to the rear of the printer over the top of the rear vents using magnets, preserving warranty validity and ensuring easy attachment and...

All parts print on Anycubic photon. Because of the slight variations in fan sizes some filing of the inside of the fan box parts may be required. I used Gorilla tape just to make sure the fans were sealed since you are venting the exhaust through a...

I needed a vent adapter for my new Anycubic Photon Mono X and didn't like the ones already here with the vent pointing straight back so i chose to make my own that's angled to the side. So far there's 4 versions, with differences in screw length and...

I tried to install a magflexplate system ( https://www.magflexplate.it/ ) on my Anycubic Photon D2. Problem was the system has an overall hight of 4,5 mm and the printer does not allow to set the zero parameter above the endpoint of the rail. The...

This is a remix of the other Easy-Bed level mods for the Anycubic Photon printer. The last version broke and deformed after a while, so i designed this version, that is a little bit sturdier and features threaded inserts for the Locking screws.One...

I recently purchased the Anycubic Photon M3 Max and couldn't find a lid online. I remixed the mono X lid from Nicolasfromparis with the following changes: 1) Modified size to dimension of M3 Max Vat, including curve out to pour spout on the vat...

There seems to be no hanger for photon mono 2 existing in Thingiverse at the moment, so I created this.

#Description# This is a longer z-stop flag for the Anycubic Photon Mono 4k with the newer version of the build plate arm which has a curved back where it mounts to the z-axis carriage. This z-stop flag is 4mm longer than the original metal piece,...

This is a custom-made adapter designed for using a 92mm fan in place of the rear panel on an Anycubic Photon 3D Printer. The main purpose of this adapter is to install an activated carbon filter element that draws fumes out of the printer through the...

The Anycubic Photon S top cover design is fragile and susceptible to cracking or shattering near the hinge, unlike its predecessor. The top cover should never be allowed to open 180 degrees, which puts excessive strain on the thin plastic frame. My...

Simple vat cover for the Anycubic Photo Mono M5s resin printer.

8mm and 21mm spacers for 92x25mm and 92x38mm fans. ... I haven't printed these yet myself but you can print them on the Photon by printing it vertically.

Can be printed on the Photon M3 or any FDM printer. ... First generation, if there are any problems let me know.

I just bought an ANYCUBIC Wash and Cure Station and noticed that the buildplate Adapter is only for the old ANYCUBIC Photon. So I created an adapter fpr the ANYCUBIC Photon Mono. ... Update 01.12.2020 I added a smaller variant for larger prints.

You might also be interested in these topics: How to calibrate your exposure time: https://github.com/altLab/photon-resin-calibration?fbclid=IwAR06rlwNx4kWLCfTfY1CANumRgU0ohte1M7undZWjIbRVAB_O0DPgniykX8 And the Resin Curing Time Sheet Finder:...

If you are greedy like me you can use this extension to grab any single drop from Anycubic bottle resins ;)

If printing is complete，Use this will save resin Did a nice logo on the file added the .Photon file with supports :) remix from https://www.thingiverse.com/thing:2930511/files

Print the object with no centering ring directly onto the plate and the other with support using a printing service, specifically designed for use on a Photon S device.

... the printed bracket and slide the block over the rails. you can now trim the bottom of the linear rails flush with the z rail once thats all cleaned up you should be good to reinstall the components and re-level your platform! ... Happy Printing!

Blocks to hold the cover in place! ... if you use an optional seal or not....hold cover in place.. The inspiration comes from my Anycubic Wash&Cure Plus...

Couldn't find a buildplate drain bracket for the Photon Mono SE that can be left on during printing (it seems like the regular Photon buildplate attachment is really close in size but I'm not sure). Holds buildplate at an angle so all the resin drips...

It also helps if your Photon is positioned under a wall cabinet, as it now only needs to be opened halfway (at least with mine). You can use a single one of these parts, which includes STL files for both right and left sides. ...I installed them on both...

... you to securely hold a 70mm square active charcoal filter just like this one: https://www.amazon.co.uk/gp/product/B074J8515D. ...Whether you're using an FDM or Resin (Photon) printer, you can easily print this adapter and get started with your project.

Made another cover for the Photon Mono because the others i found here on Thingiverse didn´t fit or it wont pass the screws which holds the vat in place when i tried to put the lid on. ...The distance from gap to gap on the lid is 15.2 cm.

i desing this angled cover inspired from @scottyujan desing but his was to big for my 3D Resin Printer so it's a smaller piece that works better for my Photon Zero printer. ... i suggest fliping the 3d model to a 90 degree angle for easier printing...

Made another cover for the Photon Mono because the others i found here on Thingiverse didn´t fit or it wont pass the screws which holds the vat in place when i tried to put the lid on. ... The distance from gap to gap on the lid is 15.2 cm.

This is a support for avoid to find a free place for the top cover. ...It simply hang to the printer itself. Printing: PLA, no spécial think. Here is the full desciption on Instructables : https://www.instructables.com/Photon-Mono-Top-Cover-Support/

standard from the Factory ) i spent almost 4 days with Support and eventually there sending a New Nut - as I didn't want to wait and will probably upgrade the factory nut to something better I designed & printed a temporary nut for the top on my FDM...

Remixed from https://www.thingiverse.com/thing:3671334 Specially designed for the latest Photon Zero resin printer, this updated model features smaller components, scaled down by 15% to fit perfectly on the new device. ...Additional stand extenders are...