anycubic photon cleaning 3d models

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

Center this within the slicer for your Anycubic Photon, and then print it. Count the ridges on the sides. There should be exactly ten of them. The ridges are a precise 0.25mm wide and 0.5mm apart. For each one missing, you're losing a significant...

This is a Remix of Skody01's Anycubic Photon M3 build plate drain. I modified it so that the whole build plate is positioned 15mm further to the rear. Now it will not collide with the cover when the build plate is positioned further upward. ...

This is a z limit spacer for the Anycubic Photon Zero. It allows you to raise the height at which your z limit triggers for the Wham Bam FBS bed. This replaces the current metal bracket that blocks the sensor. The only difference between this and...

... together using superglue (CA Glue). This design enables the use of screws that already hold the vent-plate on the back of the Anycubic Photon. ...The full un-split version is included, along with the Solidworks source file for further modification.

This accessory, designed to replace the upper glass of the Anycubic photon printer, will draw in part of the odor emitted by the resin during printing and, with a rubber tube properly connected, discharge it outside. For example, allowing the tube to...

This is my own try to make the vat for Anycubic Photon Mono X, since I wanted to make a drain stand for the Vat. I dont claim that it is totally exact as the original but as close as possible I could make it. If anyone finds anything wrong with it...

It's compatible with Epax-X1 and Anycubic photon vats, possibly other models as well. I built this using 10mm aluminum pipe for the legs and 8mm pipe for the rotating pins, which I happened to have on hand. The funnel holder is made from M5 screws,...

This is a minimal extruding replacement for the back vent plate of the Anycubic Photon Mono SE 3D SLP printer with a 4" vent that can be used with a 4" Inch Inline Fan to vent the fumes. NOTE: This item hasn't been printed or tested yet, but the...

I know, there are some vent systems for the Anycubic Photon already available but I didn't find one that includes a rear fan, which is why I designed this one. ... What you need: * 1 - 92x92x14 mm fan (Noctua NF-A9x14) * 4 - M3 x 16mm socket head cap...

I wanted to give it a more personalized feel to this cover so I added the Photon and the Anycubic logo to it. Please notice that the area where the big logo is located is very thin and some might assume is not full uv-proof. I am fine with mine....

I am creating two versions of my rear vent duct adapters for the Anycubic Photon: a 4" version for connecting to standard ventilation tubing and a 2.5" version for connecting to vacuum hoses and smaller tubing. To install, follow the instructions on...

I liked IKE_144's remix of Ermai's build plate holder that makes it so you can angle your Anycubic Photon (or Qidi Shadow 5.5s in my case) build plate over the vat to help with dripping from different angles. My printer doesn't do bridges very...

... Easy to print (just check the picture for correct orientation), and if you're using a photon, don't forget to hollow out the parts to save on resin. The funnel with filter I'm using is made from silicone - just expose it to UV light to clean it.

This device is designed to be attached to the Anycubic Photon, specifically aimed at reducing the smell from resin use.\r\nA brushless fan with an 80mm diameter should be installed between the panel and the box, secured in place using m5...

Rear bulkhead of the Anycubic photon is a crucial component that requires precise installation. Two versions are available, one identical to the original and another adapted specifically for the ethernet connector. Key steps include preparing the...

I made this little adapter so that I could use my Anycubic Photon build plate with the Elegoo Mercury Plus. It is a small quick design that can be quickly printer and used. It is designed to reuse the main bracket hardware that comes with Mercury...

FEP-Ersatzrahmen für einen Anycubic Photon Zero. Der Originale ist geklebt, so das ein Austausch nicht so einfach ist. ...Ich habe den Rahmen von bsweeney930 heruntergeladen und dann soweit modifziert das der FEP-Film besser gehalten wird.</p> <p>Am...

Hi!I made this for my Anycubic Photon Mono SE. This is the 4th iteration and can be printed at very high speed and still be functional.&nbsp;</p><p>Settings I used:<br>Line Width: 0.6mm<br>Layer Height: 0.28mm<br>Speed: 120mm/s<br>Material:...

@DocTanner crafted an innovative Rear Vent duct adapter for the Anycubic Photon, available here: https://www.myminifactory.com/object/3d-print-64661. I sought to enhance this design by adding a feature that would allow me to incorporate filters...

My Anycubic Photon S has 2 exhaust fans in the rear of the build chamber. These exhaust fans have housings on top of them with small bags of activated carbon inside. This filter box is simply a container with holes in the bottom that are small enough...

SHOULD WORK WITH ANYCUBIC PHOTON S BUT HAS NOT BEEN TESTED FOR IT! ... INSTALLATION: 1) Unscrew the two screw under the plate mount in the front right corner 2) Insert the spacer between the metal plate and the plate mount 3) Retighten the two...

This is designed for straining and collecting debris from anycubic photon vat systems. It can be particularly frustrating to go through the straining process after encountering failed prints, especially when the hardened resin is not visible at all...

Simple angled Photon Mono Build Plate holder. ...Heavily inspired by this design for the Photon Zero: https://www.thingiverse.com/thing:4224960 Modeled in TinkerCAD.

I've printed different drainer for the Photon but no one fits on my Photon Mono 4K. ... So i designed this one.

Full discloser: This filter system was made by  RJ Maker and here is his links, i just made an adapter to fit it on to the anycubic photon: Original files https://www.thingiverse.com/thing:1305485 and his youtube video that explains everything. The...

A knob for the build plate on the Photon Mono X

Simple damper feets for Photon Mono 4K (maybe also fit on a regular PhotonMono)

Wanted a lid to cover the resin vat of a Photon Mono SE.

All parts print on Anycubic photon. Because of the slight variations in fan sizes some filing of the inside of the fan box parts may be required. I used Gorilla tape just to make sure the fans were sealed since you are venting the exhaust through...