anycubic photon clean vat 3d models

This is a replacement knob for the Vat of the Anycubic Photon Mono X. It's designed to accept the bolt from the factory knobs. ...Just break off the remaining degraded plastic and the bolt should slide into the knob.

:-)Inspiriert durch das Design "Anycubic Photon VAT Lid by KayIOA" (https://www.thingiverse.com/thing:2837171) habe ich einen Deckel für den Resinbehälter meines Anycubic Photon Mono entworfen ... mit einem Logo.</p><p>Im ersten Schritt das Logo in...

I designed it specifically for my vat, which is used with both the Elegoo Mars and the Anycubic Photon, but added an inner lip to prevent the FEP from touching the bottom. ...This setup means that the FEP might sag slightly, since it's completely...

Its a resin vat cover for the Anycubic Photon Mono SQ, to keep the light out and the smell in. &nbsp;I couldn't find one ready to go, so here it is. &nbsp;</p><p>It could probably be a bit thicker, but it stays semi-flexible this way. &nbsp;It...

If you have a Anycubic Photon Mono M5s or M5, You can find this object useful.The cover allows to close or open the vat without removing the screws.Print suggestions.The print process is not difficult.I used this parameters:FIlament: Treed Filaments...

Owners of Anycubic Photon Mono 6k may be interested in modeling a lid and base for their resin tray (VAT). Modeling done with Freecad. The lid prints on the tray of a Prusa MK3S, the base is a bit larger. ... For my part I printed only the frame of...

... took the design from the user zylgross and remixed it to add the AnyCubic logo either in recessed lettering or raised lettering. ... Will ONLY fit the AnyCubic Photon Mono X. ...No other changes to the design was made and all credit goes back to him.

VAT/resin tray for Elegoo Mars and Saturn and Photon (maximum tray height: 31.5 mm). For mounting, 1 piece of 31-32 mm square wood or a 30*30 mm minimum square aluminum tube is required. 4 wood screws or 4 self-drilling screws for aluminum, 3 mm*10...

This is based on the design by FLACCUS: https://www.thingiverse.com/thing:4507757 Modified to work better with the Anycubic range of resin printers [tested on original photon and mono]. Modifications: -Changed feet so that it works on less than...

Resin Station V1 is to strain your VAT into another VAT, Bottle (both 500G &amp; 1KG supported by adjustable post and attachments! Also the VAT lid and the storage tray allow you to store your VAT with or without resin in it and should be light...

https://www.thingiverse.com/hans-g/collections/3d-printer ------------------------------------------------------ If you have an Anycubic Photon Mono X, everything turns out a bit bigger. I have therefore drawn and of course printed a holder for the...

2 part lid that clips together over the build plate and resin vat to help prevent UV light hardening the resin.

Remixed the VAT Stand https://www.thingiverse.com/thing:4674504 I have moved the funnel a bit and angled the receptacle for the tank a bit.

2 part lid that clips together over the build plate and resin vat to help prevent UV light hardening the resin.

This cover set is engineered for FEP vats, ensuring they can stack securely so multiple filled vats can be moved without any risk of spills. The base is designed to hold back resin in case of a slow leak and supports the vat by its edges, preventing...

I stumbled upon the Vat Drip bracket by QuickbeamX and was really impressed, but what caught my eye next was a simple device that could dispense the solution directly into the bottle.

... this funnel was created specifically for Foton Mono. With it, you can safely drain the resin from the vat directly into the photopolymer bottle. ...There is also a filter that will trap solid particles that can form in the resin after printing.

The bracket is designed to stand back from the wall due to the risk of spilling during the process of tipping the vat and placing it into the bracket. The top of the vat could hit the wall, causing an unwanted mess. The cup holder is specifically...

I know there are several lid variants here on thingiverse, but all I've seen so far have to remove two bolts holding the VAT. My version just slides in place without need to unscrew it. It have two variants: left and right parts to glue together for...

Discovering new ways to spark creativity is a thrilling adventure that never ends. One amazing resource that has captured my attention is the Inspire model from Thingiverse, a community-driven platform where designers and makers share their...

Verify the measurements and ensure the components align perfectly with your requirements, especially when utilizing the wooden base. ...The supplied vector files have been optimized specifically for the wooden stand, precision-cut from 5mm-thick...

This creation was engineered using Tinkercad's intuitive design tools. ...Revise and refine it directly within your web browser at https://www.tinkercad.com/things/6jB2Hcd0zrG.

Designed to be used on a 2020 aluminium extrusion. There are two models. One for Misumi extrusions that have a 6mm channel, and the 8020 5.3mm channel. The cam lever, will lock the holder at the height you desired. Thanks to mgsx for the design...

Remix with handle to make easyer removal

This design is intended to hold resin in additional tanks. It provides a tight fit (0.3mm all around), but will still accommodate most printers when they are properly calibrated. However, it's worth noting that many printers lack proper...

Designed to be used on a 2020 aluminium extrusion. There are two models. One for Misumi extrusions that have a 6mm channel, and the 8020 5.3mm channel. The cam lever, will lock the holder at the height you desired. Thanks to mgsx for the design of...

<p>This thing was made with Tinkercad. ...Edit it online <a href="https://www.tinkercad.com/things/fB7MHcd0zeB">https://www.tinkercad.com/things/fB7MHcd0zeB</a></p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Creality</p> <p...

This is a Resin Drainer for Anycubic Photon Vat. The Drainer is designed to be 3D printed in FDM with very few supports. To activate support, select only the file called "vat drainer" and choose "from platform" in Cura settings. You can print at low...

Photon Mono Vat Cover. ... Designed with Fusion 360

Der neue Anycubic Photon M3 ist in DE erhältlich. Er druckt in beachtlichen 163x102x180 mm. Allerdings findet sich auf dem Kontinent noch kein Anbieter für FEP oder VAT. Daher habe ich einen passenden Resinbehälter entworfen und angefertigt,...