anycubic photon clean vat 3d models

This box with a Nikon logo lid holds several SD and CF cards in place side by side.\r\nUpon printing the original design on my photon, I encountered issues - the lid and the box did not fit together properly, the CF section was too small for my CF...

Designed in Fusion 360 This backplate is precision-engineered to provide a secure fit on the Anycubic Photon Printer, ensuring smooth and hassle-free operation. The design takes into account the printer's unique geometry, guaranteeing a perfect...

this will allow you to pop the sensor up and out of the rail (do not remove fully or pull out farther than needed!) Remove the rear cover and 4 M3 bolts on your Photon (obviously make sure your vat is removed first) Access the 4 M4ish bolts that...

It allows you to vary the thickness of the spacer.After I tried to install this on my Photon M3 it turns out that the original file can interfere with the linear bearing unless you are very careful. ...I have made changes to limit that potential on both...

Center this within the slicer for your Anycubic Photon, and then print it. Count the ridges on the sides. There should be 10 of them. The ridges are 0.25mm wide and 0.5mm apart. For each one missing, you are losing 0.25 to 0.50mm of LCD pixels from...

Couple brackets for the Anycubic Photon Mono X's power supply. Print 2. Install screw through bracket, there's a hole for a screwdriver. Recommend scaling up maybe 2-3% because I made it too tight. ...Screws are #6.</p> <h3>Print Settings</h3>...

Riser for the Anycubic Photon M3 lid to allow passage of a small power cord in the back left corner. Useful for things like heaters, air cleaners, etc. Print the single piece if you have a big enough printer. It has also been split into four...

This is a Remix of Skody01's [Anycubic Photon M3 build plate drain](https://www.thingiverse.com/thing:5674605). I modified the inclined holder to also incorporate a slight angle (7.5°) towards the back, so that the resin flows towards only the left...

This is designed for a window guide width of 1.1inch see picture and a 3inch exhaust duct.  These parts are designed to be printed on the Anycubic Photon printer.  I suggest printing with ABS resin.  Additionally the parts are designed to be a...

This base allows for easy venting of the Anycubic Photon S into a 4" duct, enabling exhaust into a charcoal filter or outdoors. The Anycubic Photon S lacks an easily replaceable vent grill like its original counterpart. This new base is designed to...

Wash machine for Anycubic photon mono. Designed to fit any plastic container you can buy. To adapt to your container, you need to measure its width and depth, and then scale the "bearing_axis_(scalable)_2psc.STL" part according to the measured values...

I just bought an ANYCUBIC Wash and Cure Station and noticed that the buildplate Adapter is only for the old ANYCUBIC Photon. ...So I created an adapter fpr the ANYCUBIC Photon Mono.

Another version of the great “ANYCUBIC PHOTON Easy Leveler” by wundel https://www.thingiverse.com/thing:3096818. In this review, only two improvements are notable - pressure springs have been included to avoid holding the plate in place with your...

Adapter for Photon Mono buildplate to mount on Anycubic Wash & Cure Station. Uses M6 screws, like the original. I used a height of 15mm instead of 12mm of the original mount on the Photon Mono. It makes everything a bit more stable and for me...

Another Version of the Genius “ANYCUBIC PHOTON Easy Leveler” by Wundel https://www.thingiverse.com/thing:3096818 In this Review, Only Two Improvements Are Made - Pressure Springs and Insert Positioning The only improvements made to this design are...

I know, there are some vent systems for the Anycubic Photon already available but I didn't find one that includes a rear fan, which is why I designed this one. ... What you need: * 1 - 92x92x14 mm fan (Noctua NF-A9x14) * 4 - M3 x 16mm socket head cap...

This is a z limit spacer for the Anycubic Photon Zero. It allows you to raise the height at which your z limit triggers for the Wham Bam FBS bed. This replaces the current metal bracket that blocks the sensor. The only difference between this and...

... together using superglue (CA Glue). This design enables the use of screws that already hold the vent-plate on the back of the Anycubic Photon. ...The full un-split version is included, along with the Solidworks source file for further modification.

This accessory, designed to replace the upper glass of the Anycubic photon printer, will draw in part of the odor emitted by the resin during printing and, with a rubber tube properly connected, discharge it outside. For example, allowing the tube to...

Temperature controller for Anycubic Photon S (probably works with other versions too). Required parts: PTC Heating Element: https://www.amazon.ca/gp/product/B07FJW1DG3/ Temperature Control Module https://www.amazon.ca/gp/product/B08FDTZF3Q/ ...

This is a minimal extruding replacement for the back vent plate of the Anycubic Photon Mono SE 3D SLP printer with a 4" vent that can be used with a 4" Inch Inline Fan to vent the fumes. NOTE: This item hasn't been printed or tested yet, but the...

Center this within the slicer for your Anycubic Photon, and then print it. Count the ridges on the sides. There should be exactly ten of them. The ridges are a precise 0.25mm wide and 0.5mm apart. For each one missing, you're losing a significant...

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

This is a Remix of Skody01's Anycubic Photon M3 build plate drain. I modified it so that the whole build plate is positioned 15mm further to the rear. Now it will not collide with the cover when the build plate is positioned further upward. ...

I am creating two versions of my rear vent duct adapters for the Anycubic Photon: a 4" version for connecting to standard ventilation tubing and a 2.5" version for connecting to vacuum hoses and smaller tubing. To install, follow the instructions on...

If vat is leaking, this resin stop will protect the resin from getting inside the printer.

This opening is 40mm so it fits the anycubic sized resin bottles, i am currently making a larger version that will support the larger mouthed bottles like siraya tech. My plan is to add an insert so the one support could be used for any size. ... ...

This opening is 40mm so it fits the anycubic sized resin bottles, i am currently making a larger version that will support the larger mouthed bottles like siraya tech. My plan is to add an insert so the one support could be used for any size. ... ...

Hi!I made this for my Anycubic Photon Mono SE. This is the 4th iteration and can be printed at very high speed and still be functional.&nbsp;</p><p>Settings I used:<br>Line Width: 0.6mm<br>Layer Height: 0.28mm<br>Speed: 120mm/s<br>Material:...

Rear bulkhead of the Anycubic photon is a crucial component that requires precise installation. Two versions are available, one identical to the original and another adapted specifically for the ethernet connector. Key steps include preparing the...