anycubic mega zero heated bed upgrade 3d models

I really enjoyed the trash can design for my Anycubic i3 Mega (https://www.thingiverse.com/thing:2835257). I printed it and used it for a while, getting lots of pleasure from it, but only as long as the basket with the garbage didn't fall to the...

... to support BTT SKR mini E3 v1-3. ...Space for a Pi Zero 2w have not tested pi zero but it should fit. ...Space for a 30 mm fan on the side for added cooling Uses the stock botoom platre Supports requiered for The Pi holder Category: 3D Printer Parts

New mainboard casing to support BTT SKR mini E3 v1-3. ... Space for a Pi Zero 2w have not tested pi zero but it should fit. ... Space for a 30 mm fan on the side for added cooling Uses the stock botoom platre Supports requiered for The Pi holder

Just a simple model to add a cover to the front of the Y carriage on an Anycubic MZ2 I have included a badge that can be glued on [optional] complements these V slot covers: http://www.thingiverse.com/thing:3396601 Cover @ 0.2mm LH Badge @ 0.12mm LH...

Upgrade for extruder

Got tired of the print bed pulling the extruder cables so I designed this little clip to address that problem. ...

Just a simple model to add a cover to the front of the Y carriage on an Anycubic MZ2 I have included a badge that can be glued on [optional] complements these V slot covers: http://www.thingiverse.com/thing:3396601 Cover @ 0.2mm LH Badge @ 0.12mm LH...

Upgrades for my Anycubic i3 Megaa) Direct Extruderb) Cable Chain Y Axisc) Top mount for the filament sensorV1 with the original radial fanV2 with a 5010 radial fanthe difference is only the fan mountDirect Extruder:Hotend V540x40x10 Fan Original part...

Upgrades for my Anycubic i3 Megaa) Direct Extruderb) Cable Chain Y Axisc) Top mount for the filament sensorV1 with the original radial fanV2 with a 5010 radial fanthe difference is only the fan mountDirect Extruder:Hotend V540x40x10 Fan Original part...

While replacing all the fans in my Anycubic 3d printer to make it quieter I replaced the stock 60x15mm cooling fan of the PSU with a silent 60x25mm fan. Because the replacement fan was thicker I had to mount it on the outside of the PSU, thus...

This printer is incredible and never needs any upgrades, I personally don't buy printers only to discard plastic on "upgrades", if that's what I want then I would build my own printer...\r\n\r\nHowever, this one from Anycubic should be updated with...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

this kit includes everything you need to upgrade your i3megaS from stock to upgraded :)i hope you enjoy it ;)THIS KIT INCLUDES:1-Bed leveling knobs2-Cable clip for hotend cables3-Stepper motor covers4-Sd card grip5-Dinkelmeme Logo plate6-Filament...

Fan cooler Upgrade puts the nozzle closer to the work being printed.

Because the standard extruder holder isn't perfect for the 48mm upgrade, I designed a new holding system that works great in my situation and also stabilizes the weight in the middle of the Z-axis. This upgrade also allows for cable management and a...

i made this in the free to use fusion 360, it is an upgrade for holding the wire harness and filament tube on the top of the hot end. ...assembled using zip ties

I loved the concept of upgrading my printer with an LED light, but since it prints throughout the night, I needed a button to turn off the light. So, I combined the ring design with a switch and mounted it to the side of my printer. For those who are...

**1) Optical improvements** + Making the front panel a bit more beautiful with a simple (!) frame https://www.thingiverse.com/thing:2758459 + Hide front pulley https://www.thingiverse.com/thing:2837666 + Hide rear pulley...

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

I have the Anycubic M (Anycubic I3 Mega) from 2018 with replaceable drivers: Anycubic M[Amazon EU/DE] Anycubic i3 Mega[Amazon US] But there's also a newer Anycubic S Pro (Mega S) from 2019: Anycubic S Pro[Amazon EU/DE] Anycubic Mega S[Amazon US] (if...

A custom bracket is designed to secure the heating bed of the Anycubic i3 Mega Ultrabase printer, specifically addressing a potential issue where the glass plate detaches from the heating plate. ... This specialized bracket is suitable for use with ABS...

NOTE: You must have Mesh Bed Leveling or Auto-Bed Levelling to use these spacers. After having issues with my AMZ continually needing to be re-leveled, even with MBL, I decided to create these solid mounts so I never have to do it again! If you have...

I'm not a fan of how the heat bed cable is attached to the spring of the right rear leveling screw using cable ties on the Anycubic MEGA-S. There are plenty of printable replacement cable holders out there, but I don't care for the idea of securing...

Standard Anycubic i3 Mega bed mount. ... 220 x 220 mm.

...... After having issues with my AMZ continually needing to be re-leveled, even with MBL, I decided to create these solid mounts so I never have to do it again! If you have a heated bed, I recommend printing these in PETG, otherwise, PLA is just fine.

This is a remix of original by ScottyDoesKnow , is the lock for the bed of anycubic i3 mega first Version, which has a smaller screw to level bed

This is a Bed Handle for the Anycubic I3 Mega X. It was inspired by this [handle](https://www.thingiverse.com/thing:3217199) , that doesn't fit on my Mega X. It looks like Anycubic may have changed the design of the bed plate. UPDATE 08.01.2021:...

I've obtained a Simplify3D bed model specifically designed for the Anycubic i3 Mega 3D printer. ...This model was downloaded directly from Thingiverse, where it is listed as part of project number 4091968, created using Cura software.

This mount is engineered specifically for Anycubic Kossel Plus printers, featuring a spacious 240mm glass build plate and a generous heat bed of 220mm.\nI added extra reinforcement to securely hold a round cork disk (200mm diameter, up to 6mm thick)...