anycubic mega zero heated bed upgrade 3d models

After making the adjusted version of the Gantry adapters for the Anycubic Mega Zero (https://www.thingiverse.com/thing:4743749), I had an idea for a different mounting method that make it easier and faster to remove the Base part from the Gantry. ...

This is an I3 Mega S all-in-one holder for the Raspberry PI Zero 2 and the Pi Camera V2. I use it for Octopi. The holder gets clamped to the left side of the I3 Mega S. The Pi Zero 2 Case can be slided onto the side of the clamp. The Camera case can...

Höhe 45,4 mm Abstand zur Oberkante von der Oberseite vom Steg 6,7mm Wandstärke 2,5 mm 20 % Infill Nachtrag 07.01.2021 für den Innenbereich des MEGA ZERO passen die 100 mm Kästen besser. Hinten links in die Ecke passt dann zusätzlich der kleine...

I made a clip for the left side of the X-Axis of an Anycubic Mega Zero printer. The .stl does NOT have the Pi-Cam holder already attached, because the one I used has a no-remix license. But now you can choose based on your camera module. For me, it...

**Update 09-07-2021 (Added Mega_Zero_Fan_Duct for 5015 & silicone sock Rev07c.STL): This version sits 2.5mm lower and the outlets are shortened with 1mm to prevent interreference with a silicone sock. This is a work-in-progress version to see if it...

It's tough to fit wide spools on a regular filament holder for the Anycubic Mega-S printer - they just won't stay put. ...This spacer lets you easily mount these larger spools without messing up the look or adding extra plastic costs.

... might need 4 screws, that are just a bit longer than the original, to install the box. And you will need 4 M3 nuts. The fan duct you see in the picture is this (Anycubic i3 Mega S - Fan Duct by matism09): https://www.thingiverse.com/thing:3564168

Only the Left bracket has been modified to suit the different frame design of the Mega Zero v1.0, the Larger Right side bracket is the same. Installation: 2x M4 12mm Cap-head Bolts and washers to fix the *back* of the PSU to the Printed Mounts ...

The construction file *.ipt made with inventor, the *.stl file and a *.gcode file, made with Cura for the Mega X. Summarized you only need to print my part and order the new fan. No additional parts needed. ...The difference in noise is remarkable.

Frankensteiner hood is a very nice product. ... I like it so much that I modified it to carry the Sherpa mini. And because the Sherpa monn motor has heat, the fan is enlarged to 60mm and the inside is split so that the wind cools the motor. ...

This set of parts is for the Anycubic I3 Mega with Ultrabase. Included are: A hotend enclosure to replace the existing metal housing. A hotend base cover that fits securely over the new enclosure. And a parts cooler that pairs perfectly with a 5015...

Parts needed - Raspberry Pi Zero 2 - SSR - LM2596 (RPI power supply) - 4-Channel Logic Level Converter 3.3V-5V [Aliexpress](https://aliexpress.com/item/32806476867.html) - 2x M3*12 screws and nuts (for LM2596) - 2x M3*8 screws - 4x M2*12 screws and...

... when I tried to replace it, I found that they were incompatible. And I designed it separately for MZ1. I only have the MZ1, so I don't know if it works for the MZ2. And that of the MZ2 didn't fit in the MZ bed, so I had to separate it. ...

The Ft-i3 Mega's heated bed is designed with a built-in strain relief feature that can be easily secured using two-sided tape directly onto the ACM bed's surface.

This case is designed to hold a Raspberry Pi 4 and a AZDelivery HW-140 DC-DC Buck Boost Power Converter (https://www.amazon.de/gp/product/B08T1SXF6M/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1) Case has been design for optimal airflow to keep...

I designed this filament guide to extend the loop of filament away from the printer, and reduce the strain on your Bowden tube. I printed mine in Purple Silk PLA and it worked out quite well. I do recommend PLA I hope you find this design...

I designed this guide to extend the loop of filament, and reduce the strain on the Bowden tube. I have built mine in Purple silk PLA. I hope you find it handy! ... Enjoy!

I had some left over parts from a Camera mount that I wasn't using anymore lying around. The mount itself was great but there wasn't a great position to mount it on my printer with the original system. Since I for some reason cannot link this as...

Carcasa original adaptada a la placa BTT SKR_V1.4 //////////////////////////////////////////////////////////////////////////////////// Original enclosure adapted to BTT SKR_V1.4 motherboard

Humans love to enjoy and share their creations.

Remix of the Camera holder for a C270 Webcam on the x-axis servo. ...Please remember to mirror the build so that it will work.

Small bracket to guide the Z spindle. ...Used bearing 608 22x7x8mm

I used 2 M4 insets for plastic and M4 screw to fix it to the extruder support. Also has a round shape for clearing the z-threaded-rod washer. ... https://www.amazon.de/gp/product/B085CBMS6S/

these go on the side blower fan to make it look cleaner and to stop the screws from bending the brackets sizes shown in picture and are easy to slip in. perfect size! ... take about 5 mins any questions please ask 4.4mmx4.4mmx2.08mm

Lead Screw Stabilizer

Fixed version of fan holder. Original version is splitted to two parts (the mount is separated from the base) You will to have 2 screws M2x14 and one M2x18 for install. ... upd: added second version

I designed something similar before, but it was incomplete. Therefore redesigned it so that they were solved and the filament reels would rotate more smoothly and they wouldn't come off. following parts are required. ... bearings 608zz x 2 M3 x...

Created to give more space to the beak

BL Touch installation mount. Mounts over X_MIN limit switch using existing X_MIN limit switch screws. Nozzle to Probe Offset values as follows: NOZZLE_TO_PROBE_OFFSET{-37, -13, -2.195} Please note that the Z will vary depending on your...

Enjoy an share your make