anycubic mega s 3d models

to fit mega s. for use with standard hot end and extruder mounted to side. ... will need to print about 27 chain links

Hi, I created the holders of two cable chains for the Anycubic i3 Mega. The first cable (chain holder 1) goes up on the right side above the Bowden extruder (chain holder 2) and the second up to the printhead (chain holder 3). ... I have this print...

Hi, I created the holders of two cable chains for the Anycubic i3 Mega. The first cable (chain holder 1) goes up on the right side above the Bowden extruder (chain holder 2) and the second up to the printhead (chain holder 3). ... I have this print...

I replaced the stickers on the Mega-S with new ones that completely covered up the white lettering on the front, using 3M's 468MP adhesive to secure them firmly in place.

Made a mount for the Mega S on the spool holder to hold the Rpi camera for octopi. ...Just the mount is changed, everything else is the same as SmartBlug's models.

This remix has an 8.5 mm hole to accommodate an 8 mm OD spring. Print with supports. Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: Yes Resolution: 200 Infill: 100 Filament: Eryone PETG Category: 3D Printer...

Hallo, nachdem ich in meiner Einhausung vom Mega S das Filament nur recht umständlich laden und entfernen konnte, habe ich mal diesen Seitenhalter für den Extruder konstruiert. Es gibt zwar schon einige hier auf Thingi für den Mega, aber keinen für...

I wanted to tidy up the cable and bowden tube at the hotend on my Mega S so drafted these little parts. They work well and look pretty nice - Enjoy Just getting started so hopefully lots more makes to come. ... I also added the inventor files -...

The spool holder on the Mega S is quite decent, but its design leaves room for improvement - specifically in how smoothly the roll glides onto the holder and the annoying noise that comes with it. To address these issues, I crafted an adapter that...

I highly recommend this printable upgrade because the hotbed cable broke off on my mega s. it fixes it better and runs smoother. You can also use larger level wheels now. To secure the cable cover you will need some screws. ... Here the links to...

Your milage may vary. -Print time is roughly 45 minutes at 50mm/s. Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: No Resolution: 200 Infill: 100 Filament: Any PETG but PLA should work Notes: Tree supports...

This is a remake of henrikfjell's LED strip bracket for the mega-s. The adhesive used on LED strip lights often fails to hold up over time, so I designed the bracket to securely grip the strip. To achieve this, I added sides to the surface that...

The total overall height of this bracket is 44mm vs the 42mm one that came with my Mega S. You will have have clearance issue with the heatsinks that come with the TMC2208 driver boards. This part will not solve that problem as the total depth of...

The spool holder that comes with the Mega-S is a nice touch, but I have to say I'm not thrilled about where it's mounted. I envisioned it sitting high and out of my way, making my workspace feel more organized. I aimed for a design that's both rigid...

... 16mm. Ich habe TMC2208 und die originalen Anycubic Kühlkörper. For 80x80x15mm fan, fits perfect. Screws M3x20mm IMPORTANT: Please measure first. From the board to the holder it is 16mm. ...I have TMC2208 and the original Anycubic heatsinks.

Making a V6 upgrade on a MegaS for a friend. ...The bowden support was not convincing so I decided to make one that I could use with an M10 tube connector...and I spiced it up with this cute little thing :P Never feel alone when your printer goes...

Might do clean-up to make it easier to print later, did not put much thought into that because I was trying to get a design that works first.Long winded story below.Got hold of a pre owned Anycubiic Mega S. Realised the filament sensor triggering a...

Got hold of a pre owned Anycubiic Mega S. Realised the filament sensor triggering a false negative of filament runout. Gave me warnings at times and stopped prints at some instances. Did some reading up and realise that sensor is for both 1.75mm...

... mini cover. ... you can see the inside of Extruder. also you can easily put filament in it. note: this thing is work in progress now. It's not 100% completed, so you may have problems with screw tightening. ... but for me, it's working nicely.

... material. ...That's where this handy tool comes in - a limiter for the filament stand that makes sure everything stays stable during printing. ...By using this device, you can improve your filament's stability and get better results from your prints.

This creation was expertly crafted using Tinkercad's intuitive design tools. ...You can easily edit and customize it right from their website at https://www.tinkercad.com/things/4auWvj87pgM.

Should not be an issue because I've only removed the fan-mount-support and the main support structure is intact. I removed the heatsink fan support structure for those that have a fan mount attached to their heatsink. Based on the excellent work of...

During replacement of bowden tube on my printer I figure out that I could reduce it's size almost twice. ...Just with this simple upgrade you will be able to have 2mm of retraction settings.Youtube: https://youtu.be/DRXus4slqecUpdate:v1 - added corner...

The clip locks firmly onto the extruder motor from beside it, its smooth edge gliding effortlessly over the motor's rear as it swings open to make contact. ...Pressing it home secures everything in position, allowing you to carefully guide the harness...

I experimented with different PLA filaments at various temperatures and discovered that if it's too cold, the LED becomes loose, and if it's too hot, it doesn't fit properly. ...However, using ice-filled filaments at 195 degrees Celsius yields perfect...

It's small, and discreetly lays underneath the bed. I decided to use a real bearing instead of printed one, but that is just my personal preference. This is an easy modification, that instantly improves print quality. I hope you enjoy! Here is a...

... all around - which is fine for my (calibrated) printer, but depending on your tolerances you might want to make it narrower for your usage. There's a 0.25mm clearance at the bottom, so it will spin freely without taking up more room than necessary.

Basically I like MrGr33n's design, but I wanted to change a few things: -Mounting on the slide from above instead of below (no falling down) -Height adjustment -Extension of the cable guide -Construction reinforcement I use this together with...

I've spent countless hours perfecting this hotend cover, and I'm confident that it's finally ready for prime time. On the overhang test, I'm blown away by the impressive results I get up to 65 degrees - it's a real game-changer. And while decent...

... position.If it works, I would appreciate sharing your makes.Clicking on my AliExpress affiliate link below will give me a small kickback if you purchase something within 3 days. (at no extra cost to you) https://s.click.aliexpress.com/e/_DmpFxU1