anycubic mega s upgrades 3d models

Filament Spool holder for the anycubic i3 mega and mega s. Mine didn't come with one second hand and all the designs on thingiverse don't work that well (especially for a direct drive extruder), so i made my own. you can mount this on the top screws...

This is a minimal version of the improved hotend for the anycubic i3 mega (https://www.thingiverse.com/thing:2919245). I made this for my i3 mega S because my radial fan was a little to big for a nice fit with the orginal desgin. Further I wanted...

This is a revised version of Junior_Barnes' Anycubic Mega-S Bed Heater Wire Support remix.\r\n\r\nThe design was reworked to give the cable a smooth curve to the right, resulting in increased stability. ...Two zipties are all that's needed to secure the...

Filament sensor fittings adapter for ANYCUBIC MEGA S. Type 1 comes pre-assembled with an extruder, while Type 2 is specifically designed to integrate with the filament sensor. ...However, users often find Type 1 difficult to replace with new filament,...

... on Thingiverse. ...The first is 3791392 and the second is 4178350. I'm focusing on creating a leveling system for my Anycubic Mega S 3D printer that incorporates up arrows. ...This will help me achieve precise calibration and improve print quality.

I wanted to install a 60mm LED ringlight on my Anycubic I3 Mega-S printer, so I built an adapter to match the existing screw holes. The Ledring attaches securely with adhesive, and you must connect wires to the second fan's electrical terminals. ...I...

... ...Here's a rewritten version of your text. A Fresh Take On The Hand/Fist Filament Guide By MechRacer84 Taking cues from the original guide, this remake brings the design up to speed for seamless mounting on the Anycubic Mega S using its top screws.

This is a custom designed protective cover for the AnyCubic MEGA S 3D printer's SD card slot, crafted to shield your memory cards from dust and accidental damage. Its sleek design allows easy access to the SD card while keeping it safe from harm.

... fan duct from H_Run. ... I created a wrap-around ring with 270° exhaust ducts. I also removed a small cutout, which is why the original did not fit my printer. This remix is for the Anycubic i3 Mega S (2020). ... Printable without any support.

[999D](https://www.thingiverse.com/999d/) provided a nice replacement for the extruder lever of an Anycubic i3 Mega S: https://www.thingiverse.com/thing:4248053 This is a remix by cutting the model in half and glued it together afterwards. ...For easier...

Direct cable access requires modification to the Anycubic i3 Mega's casing. Specifically, the red, green, and black sockets located on the right-hand side need replacement with open-ended cable passages. ...This alteration allows for unimpeded cable...

This component is designed specifically for the Anycubic Mega-S extruder, addressing a common issue with earlier versions that often got stuck on adjacent parts, hindering filament extrusion. ...The updated design resolves this problem by providing a...

Hey, I just took the standard filament spool holder from the Anycubic MegaS and improved it. It's intended to hold Filament Rolls with an inner diameter of at least 70mm. To install it on your Printer you'll need no less than 2x M5 screws and 2 screw...

... remix of https://www.thingiverse.com/thing:4193861 The original source is designed for 5015 fan and used for https://www.thingiverse.com/thing:3954252. ... In order to reuse Anycubic I3 MEGA-S original fan for direct extruder, mount was re-designed.

This little thing is a spacer for the standard spool holder that comes with Anycubic Mega S. My problem was that Redline filament paper spools were 2mm too wide for the standard spool holder. So I decided to put a 3mm spacer in between the 2...

Simple mounting plates are designed for the Anycubic i3 Mega S. These plates enable users to easily attach components to the spool holder and Z-axis. A total of two, four or six 6x2 magnets are required, which can be sourced from...

*While removing the filament in the Anycubic i3 mega s 3D printer, the tip of the filament gets stuck and it is difficult to come out. Thanks to this apparatus, you can easily remove the end of the filament by cutting it. WARNING: This apparatus is...

This attachment elevates the Anycubic Mega S by 33 millimeters, creating ample space for oversized fans to be installed. A precisely drilled hole accommodates a No. ...8 screw, facilitating secure attachment to the base of the case while allowing the...

... aus und Schützt mein Riemenmotor. Drucker : Anycubic i3 Mega S Unterstützt : ja Füllung : 25% Anmerkungen : Stützstruktur : Tree und X/Y - Abstand der Stützstruktur auf 3mm einstellen !!! ... damit ihr die Stützstruktur ohne Probleme raus bekommt!

Redesigned the noisy stock shroud for the Anycubic Mega S. I suggest a 5015 12v blower fan to replace the stock part cooler and printing this part for the blower fan: https://www.thingiverse.com/thing:2800663 I printed this on an Elegoo Mars 2 Pro...

This project is made for anyone wanted a tool-holder specific for Anycubic mega X tool kit, wit a pen case add in.

Modified the frame to fit perfectly around the Anycubic i3 Mega S, ensuring a precise margin and screen size. Mirrored the cover's design so that it can be mounted inside out, creating a seamless look even when the lid is closed - check out the...

This is a custom tube mount designed specifically for use with the Palette2 on Anycubic Mega-S 3D printers. The Mega-S model has a unique extruder housing that necessitates this tailored solution. To secure the mount in place, you'll need to attach...

A tiny seal for the i3 Mega S

I saw MKS Tinybee with mini12864 LCD going for less than 30USD and wanted to try this upgrade on my Anycubic Mega S. I have compiled the firmware but have not tested it to be fully working. I wanted to use...

... holding the bowden tube at an incorrect height, causing it to kink when homing the X-axis. This design aims to secure the bowden tube just above its coupling and keep cables organized on the left side. It's specifically made for the Anycubic Mega S.

The Anycubic Mega S i3 Glue Holder is a sturdy accessory designed to keep your workspace organized and clutter-free. Its compact design fits neatly on the side of the printer, providing easy access to glue sticks and other small items. With its...

I've built an adapter to make this case fit the Anycubic I3 Mega S. You'll need to remove the touchscreen for this to work. Note: This is currently a work in progress, and it's possible that it won't fit perfectly yet. ... Don't print it right now; I...

----------- English Guide There is also an English guide: English Guide [Thingiverse] ------------------------- With this guide, I've compiled all basic upgrades, mods, a few suggestions, and more for the Anycubic Mega S and I3 Mega. In the...

The purpose of this design is to allow the user to mount a camera on the back of the Anycubic i3 Mega S. The paddle-shaped design is mounted on the rear of the printer using two of the bolts used for stabilizing the rear servo for the print bed.