anycubic mega s upgrades 3d models

So I'm new to the 3D printing world, and my buddy who's been using an Anycubic I3 Mega S for a while recommended it to me. I've been gathering and designing upgrades, covers, and accessories for this printer to make it more efficient and easy to use....

i made this in the free to use fusion 360, it is an upgrade for holding the wire harness and filament tube on the top of the hot end. ...assembled using zip ties

If you want to support my work please donate something at this link: https://paypal.me/molinodavide [EN] MY ANYCUBIC I3 MEGA-S UPGRADE GUIDE Surfing the Internet I've found just half of the upgrades that i had in mind for my printer... So I've...

If you want to support my work please donate something at this link: https://paypal.me/molinodavide [EN] MY ANYCUBIC I3 MEGA-S UPGRADE GUIDE Surfing the Internet I've found just half of the upgrades that i had in mind for my printer... So I've...

this kit includes everything you need to upgrade your i3megaS from stock to upgraded :)i hope you enjoy it ;)THIS KIT INCLUDES:1-Bed leveling knobs2-Cable clip for hotend cables3-Stepper motor covers4-Sd card grip5-Dinkelmeme Logo plate6-Filament...

I have the Anycubic M (Anycubic I3 Mega) from 2018 with replaceable drivers: Anycubic M[Amazon EU/DE] Anycubic i3 Mega[Amazon US] But there's also a newer Anycubic S Pro (Mega S) from 2019: Anycubic S Pro[Amazon EU/DE] Anycubic Mega S[Amazon US] (if...

The E3D v6 Hotend has a nominal length of 62.3mm (see the drawing here: https://e3d-online.dozuki.com/Document/n5grN2JNoNibYeQW/V6-175-ASSM.pdf) My original Anycubic Mega-S hotend has a measured length of 70.7mm. The nozzles have the same length in...

Upgrade for extruder

But for the start it's ok. And there is no changing of extruder, drivers etc, the printer itself will stay "untouched". I printed all of them (among some others which i declined later) and still using them. If anything will come in addition...

This is a cable holder for the Anycubic Mega-S printer. It is placed in front of the extruder Motor. Fillament and cables will no longer rub against each other. The cable is held and in a good and tight position. The holder is very strong. ... To...

... on the Printhead. The Printhead Case Cover you see in the pictures is this: https://www.thingiverse.com/thing:4879416 The fan duct you see in the picture is this (Anycubic i3 Mega S - Fan Duct by matism09): https://www.thingiverse.com/thing:3564168

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

I designed an upgraded file, based on daridima's original creation: https://www.thingiverse.com/thing:3108771. With my upgrade, you can superimpose the original media over the new ones I created, conserving space in your printer. ... Dimensions: 30 mm...

Plug and play upgradeNeed: some screws and nuts (M3)4020 radial fanoriginal extruder and motor from original printer

UPDATE: I made the holder slightly wider to give the bearings more space to move freely. I also added a divided roller to glue them together. This Filament roller is for the I3 Mega-S and the upgrade kit. Started remixing and ended recreating it from...

This Filament roller is for the I3 Mega-S and the upgrade kit. Started remixing and ended recreating it from scratch in Fusion 360. It is a shorter version, as my filament spools only have a maximum width of around 6.5cm, the roll has 6.8cm. ...

Some 3DTomorrow filament customers were kind enough to inform me that the stock spool holder for the Anycubic Mega series was not well compatible with our 1kg spools of filament. I always like a challenge, so I have set out to create a spool holder...

Anycubic I3 Mega S need: some screws and nuts 4020 fan Material: PETG/PLA type: Plug and play from original printer set

Kept finding the knobs on my Mega S came undone very easily so i decided to design these they accept a M3 nylon nut. ...I used a mug to press them in (it was quite a tight fit) and made sure to put some super glue inside to make sure they don't come...

Upgraded spool holder for Anycubic Mega / Mega S with rods. ... You need 2 rods ABEC-9 608 2RS 8x22x7 and 4 M3x10mm screws Also you need a double-sided tape to attach to the original spool holder

... might need 4 screws, that are just a bit longer than the original, to install the box. And you will need 4 M3 nuts. The fan duct you see in the picture is this (Anycubic i3 Mega S - Fan Duct by matism09): https://www.thingiverse.com/thing:3564168

You need 2 rods ABEC-9 608 2RS 8x22x7 and 4 M3x10mm screws

It seems like you've provided a long text about Cura, a software for 3D printing. It mentions the following features: 1. **Cura Configuration files:** The text explains how to import configuration files for PLA and ABS materials into Cura. These...

My printer now prints at speeds up to 150 mm/s (normal speed is 95 mm/s) with an acceleration of 1800mm/s^2 and that at a volume of only 40db. The print area is now 218 x 218 mm and 210 mm high. #1. Make it quieter Increase fan openings...

Mein Drucker druckt jetzt mit Geschwindigkeiten bis zu 150 mm / s (normal mit 95 mm /s)mit einer Beschleunigung von 1800mm/s² und das bei einer Lautstärke von nur 40db. Der Druckbereich liegt nun bei 218 x 218 mm und 210 mm Höhe. #1. Leiser machen#...

Simple Anycubic i3 Mega S Upgrade with Hotend Cable Guide on the top back.

Mega X different upgrades in one place 1.Power Supply for OctoPi (Raspberry PI3) File: /5V_Power_Supply_Box_for_OctoPI_-Side_mount_on_the_printer.stl/ 2.Chain Cable Holder - hot end. File: /AI3MX_Hotend_Chain_holder.stl/ ...

Anycubic i3 mega S / Pro spool

Anycubic Mega-S SmallFeet Small feet using existing screw holes when removing the bottom panel of Anycubic Mega-S After installation, it is good to put a non-slip sheet