anycubic mega s upgrade 3d models

A camera holder with a 6.8mm hole.Inspired by: https://www.thingiverse.com/thing:3046141/filesPrinted on my Anycubic Mega S with PETG.I really like this mount, but admittedly it is still a bit wobbly in the current version Stay healthy and have fun...

This is a mounting bracket to mount a Duet 3 Mini 5 in a Anycubic i3 Mega S. Because of identical mounting hole positions, it should also work for a duet 2 wifi/ethernet. This part is tested for a *Duet 3 Mini* and works fine. No Support required....

Da ich für meinen Anycubic Mega S das X Achsen Design von https://www.thingiverse.com/Sergiu_I verwende, musste ich das Design von Sir Thommes etwas anpassen. Da ich Schwabe bin, hab ich versucht das Design so zu halten, dass Filament und Druckzeit...

This is a mount for the Anycubic I3 Mega to apply a titan-extruder like with the "original" upgrade-kit. With the bracket of the original extruder, the filament sensor isn't in the right place or it's not possible to attach the titan. This mounting...

# Anycubic i3 Mega S Bowden tube coupler > After downloading a version that was found here on Thingiverse and the threads appeared to be dimensionally incorrect, I gave up and went ahead and designed one up in Solidworks. This will fit a M10 x 1.0...

Anycubic i3 Mega S Bowden tube coupler After downloading a version that was found here on Thingiverse and the threads appeared to be dimensionally incorrect, I gave up and went ahead and designed one up in Solidworks. This will fit a M10 x 1.0 thread...

//----------------------------------------------------------------------------------------------------------// Z brace for the anycubic i3 mega. Will require drill into the sheet metal. M5 screws, washer, & nuts are needed. Needle nose pliers will...

Anycubic Mega S Top Mount Spool Filament Guide I switched my Mega S over to the MK4 Direct Drive and found the filament all over the place and rubbing up against the spool holder mount. So I designed this filament guide to work with the Anycubic...

Anycubic Mega S Top Mount Spool Filament Guide I switched my Mega S over to the MK4 Direct Drive and found the filament all over the place and rubbing up against the spool holder mount. So I designed this filament guide to work with the [Anycubic...

Yet another part cooling fan duct for the Anycubic i3 Mega S (should work fine for the non-S Mega, as I believe they have the same fan and X-carriage cover. I recently upgraded the hotend to an E3Dv6 and due to the geometry when its installed, I...

Note: This is for the Anycubic i3 Mega S with the thick (3.5mm) hot bed plate. This is probably why the other mounts kept breaking, as they were for thinner plates. Remixed from https://www.tinkercad.com/things/iLifMeAUme0 and used...

It's the little cone thing that is part of the extruder that comes with the Anycubic i3 Mega-S. I lost mine for awhile, and made this replacement. When I tried to pull it out after finding the original, it broke on a layer line and I had to pick the...

I created this simple model to mount the Eufy 2K Indoor Camera to my Anycubic Mega S.I was using Wyze cameras with the beta RTSP firmware, but they recently dropped the support that was key to my use and removed the firmware from their site.  In...

Remixed Case for my Anycubic i3 Mega S. There's a lot of cases and Mounts but I wanted it to be on the left side of my printer and cables facing back- and downwards. So i turned the raspberry logo 180° and added holes on the backside for the mount.

I merged a fantastic Pi 4 case with some mounting brackets specifically designed for the Anycubic i3 Mega. To enhance stability, I added T-shaped pegs to the mounting brackets and drilled holes with slots into the bottom of the pi case. Additionally,...

Yet another part cooling fan duct for the Anycubic i3 Mega S (should work fine for the non-S Mega, as I believe they have the same fan and X-carriage cover. I recently upgraded the hotend to an E3Dv6 and due to the geometry when its installed, I...

BeagleCam Halter für den Anycubic I3 Mega S im GoPro Style mit M5 Schrauben. Die Dateien BeagleCam_90 und BeagleCam_Straight sind die Verbinder Druckerhalter/Arme Die Datei BeagleCam_Cam ist die Verbindung zu Halter BeagleCam. Benötigtes Matrial: ...

Therefore, my new spool holder iteration takes a step back to its roots while combining some ideas and adapting it to the Mega-S. It is designed to use the original metal Anycubic i3 Mega spool support rod. A positive side effect of this design is...

... in comment what you think. Works probably only for Anycubic Mega S. Assume original fan or equivalent 45mm radial fan duct located in original place. ... The picture shows the vortex effect with water on some earlier prototype, really nice :)

Connectors to allow use of an off the shelf 10x15mm plastic chain on the heated bed cable for an Anycubic Mega X (or S). ...Two parts - the bed side “clips” onto the caddy under the heated bed, the case side has two holes that align with pre-drilled...

This is my Mod for the original Part Cooling Fan for Anycubic Printers(In my Case an Mega S). Because there are not many useful Fanducts available i thought it would be a good idea to make my own. I use this E.V.A. Duct on my modded Any and I...

I wanted a simplified way of adapting my knock-off gopro to the anycubic mega s (i3) that wasn't connected to the bed or at a cumbersome location/angle. This felt like the perfect solution. I've been using it for several dozen prints now, all...

Spoolholder for the Anycubic i3 Mega 3D Printer. With an outer diameter of 50 millimeters, this spool holder securely attaches to the printer's plate via two screws that need to be removed and then replaced once the holder is in place. Simply reverse...

Ho disegnato io personalmente perchè la scheda del sensore della Anycubic i3 mega s,non si trova più o almeno non sono riuscito a trovarlo da nessuna parte... se si installa la sua vite originale, la staffa che va a sbattere al pulsante del sensore...

It's tough to fit wide spools on a regular filament holder for the Anycubic Mega-S printer - they just won't stay put. ...This spacer lets you easily mount these larger spools without messing up the look or adding extra plastic costs.

Update 1: - Duese_Mk2 mit verbessertem airflow hinzugefügt ---- English: I didn't like the original extruder case on the Anycubic i3 mega s. The parts cooler also bothered me because it only cools from one side. That's why I looked for an...

This is a MK4 inspired Y-Carriage for the Anycubic i3 Mega S.As I needed a tensioner for my Y-axis, had printed too many parts for my MK4 X-Carriage anyways, I designed a MK4 inspired Y-Carriage for my Mega S.You will need the 06_Belt_Tensioner.stl...

You should be able to use the case bottom with any of Malolo's case tops. Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: No Resolution: 0.2mm Infill: 100% Filament: Creality3D PLA Red/Black Category: 3D Printer...

There are quite a few spool holders for the Anycubic Mega S. I wanted something that could simply fit over the existing spool holder without any assembly/disassembly. It is a nice tight fit and works perfectly. Using .2 layer height @ 60mm/s, it took...

This is my first attempt at any 3d design/editing/remix so apologies if it's not perfect :D Link to origonal Thing: https://www.thingiverse.com/thing:3359648 Print Settings Printer: Anycubic I3 Mega-S Speed: 65mm/s Adhesion: Skirt Supports: Yes (but...