anycubic mega s enclosure 3d models

I designed two different mounting arms, one turned outward for the Mega X and one straight that fits Mega S and Pro. I printed everything with PETG. The holding arms and the roll were printed with 60% infill density and 0.15mm layer height. The...

Anycubic I3 Mega S Z Stop uses a 2.5mm locknut to interact with z stop micro switch. The lack of a sufficient planer surface to interact with micro switch actuation lever causes extreme variation in Z homing resulting in damage to a great work bed...

An extruder and cable guide for the Anycubic Mega S. Meant to keep the cabling / Bowden tube away from the z-axis leadscrew. You'll need 4x 3mm or 4-40 screws, lock and flat washers from your junk drawer. Print using no supports, I used PETG but...

I made this dual sided fan duct as a slightly improved / better fitting version of the original dual-side fan duct made by H_Run. The original one had some fitment issues on my printer (the fan shroud was too big and too far up). I also changed it...

Just a very simple bracket to mount a common 60x10MM fan for the mainboard in an Anycubic Mega S. Uses stock hardware locations, clears original stepper drivers. No major disassembly other than removing the bottom plate of the printer is required.

An extruder and cable guide for the Anycubic Mega S. Meant to keep the cabling / Bowden tube away from the z-axis leadscrew. You'll need 4x 3mm or 4-40 screws, lock and flat washers from your junk drawer. Print using no supports, I used PETG but...

This is a mount for the Anycubic I3 Mega to apply a titan-extruder like with the "original" upgrade-kit. With the bracket of the original extruder, the filament sensor isn't in the right place or it's not possible to attach the titan. This mounting...

The E3D v6 Hotend has a nominal length of 62.3mm (see the drawing here: https://e3d-online.dozuki.com/Document/n5grN2JNoNibYeQW/V6-175-ASSM.pdf) My original Anycubic Mega-S hotend has a measured length of 70.7mm. The nozzles have the same length in...

At some point I was not satisfied with a filament spool holder of my Anycubic Mega S - it was too much friction there. So I did a quick design of a simple attachment based on conventional 608 bearings, which are cheap and are used everywhere -...

This is a Remix of the Anycubic i3 Mega-S dual side fan duct by kb-elmo. I liked this design because it matches the sharp lines of the rest of the printer, but it had modeled supports in the duct which blocked airflow a lot. I edited it in...

This is a mount for the Anycubic I3 Mega to apply a Bondtech-extruder (or BMG clones). With the bracket of the original extruder, the filament sensor is not in the right place or it's not possible to attach the BMG. This mounting may work with all...

Gcode for the Anycubic i3 Mega S to assist in the levelling of the bed with the paper method. PLEASE NOTE: Just use the .GCode file from the files on this download. The .STL file won't do anything but had to be added to this thing otherwise...

Yet another part cooling fan duct for the Anycubic i3 Mega S (should work fine for the non-S Mega, as I believe they have the same fan and X-carriage cover. I recently upgraded the hotend to an E3Dv6 and due to the geometry when its installed, I...

My mounting part is only compatible with the "Mega S" due to its reliance on the original metal filament holder as the mounting surface. Screw holes for fan attachment are approximately 4mm in diameter, making it simple to create threads without...

Here's my revised half-circle version for the Mega-S: https://www.thingiverse.com/thing:3733579 And here's my updated half-circle hotend cover version for the Mega-S: https://www.thingiverse.com/thing:3736680 EDIT: I added an updated version with...

Hi all, I've remixed the original cable shroud and added the Mega S logo to the hotend cover's front face. I also added the blank version without the letter "S" for other Mega series users can customize it. You can use a double sided tape to...

I found some mounts for Mellow's BMG Aero and Anycubic i3 Mega (S) but all of them was a bit disappointing. So I created one myself. With drag chains, LED light, integrated X belt tensioner an so on. I tried to use as much stock components as I can...

The filament end sensor as installed on the Anycubic i3 Mega S is a bit of a problem. The filament is always pulled from the inner side of the spool which can lead to jumping filament when it comes from the outer side. These cracking noises are worse...

Yet another part cooling fan duct for the Anycubic i3 Mega S (should work fine for the non-S Mega, as I believe they have the same fan and X-carriage cover. I recently upgraded the hotend to an E3Dv6 and due to the geometry when its installed, I...

Dadurch sollte sich das PSU kältere Luft durch die seitlichen Löscher und nicht die warme ziehen. Dazu habe ich noch ein paar Wände schmaler gemacht (eher schnell und unsauber), dadurch sollte man etwas Zeit und Material sparen. Hoffentlich klappt...

Couldn't find a cable holder that i liked so made my own. ...this fits my mega pro but should fit the s. ...It's bolted to the bottom slide plate and is solid and takes all the pressure of the solder points on the heat bed.

Kept finding the knobs on my Mega S came undone very easily so i decided to design these they accept a M3 nylon nut. ...I used a mug to press them in (it was quite a tight fit) and made sure to put some super glue inside to make sure they don't come...

This is a remix of "dkcwenge" design of fan duct for Mega-S i've changed the connection holes, so a noctua Fan (40x10 or 40x20) would fit without screws now ;) Thank you for providing the step files ;) i've printed it with tree support, the only...

DIY Camera Mount Kit for Anycubic S Pi Cam Featuring a Customizable Spool Holder Design Looking to capture stunning footage with your Anycubic S Pi Cam? Look no further! Our camera holder kit is designed specifically for this popular camera model,...

Anycubic i3 Mega S Y-Carriage Belt Tensioner UPDATE: Added a Carriage_mk2 file which features a slightly sturdier back. I noticed after a year of use and perhaps slight over-tensioning on my part, the screw that pulls the carriage back has started...

... I have created a smaller version to fit the right-front corner and the back-center. A M3-.50 nut is required. I tried the Drag Chain of RTamer, but the connector didnt work for the i3 mega s, so I added this thing to get it done directly.

...... I designed this **X-axis belt tensioner** to fit onto an **Anycubic i3 Mega S** because there isn't one that I could find readily available on here. You can install this onto a stock Ai3MS with **no modifications necessary** to the current fixture.

I designed this X-axis belt tensioner to fit onto an Anycubic i3 Mega S because there isn't one that I could find readily available on here. You can install this onto a stock Ai3MS with no modifications necessary to the current fixture. No need to...

Das ist eine Halterung für den Anycubic I3 Mega um einen Bondtech-Extruder (oder einen BMG-Klon) montieren zu können. Mit dem Halter des originalen Extruders passt die Ausrichtung zum Filamentsensor nicht mehr, der Extruder steht seitlich über oder...

Spool Holder - Nice & easy improvement for Any*cubic (i3 Mega S/Pro) English: With this spool holder the filament simply rolls softer, because the holder now has a round surface. The roll does not jump off anymore and filament is transported better....