anycubic mega s change filament 3d models

Altered the dimensions to better fit the frame of the Mega-S. Added a corner relief and a lead-in on either end for the frame corners. Infill doesn't seem to matter too much, especially if you add more walls. **UPDATE** It might be a bit too long...

Jedynie co będziemy potrzebować to dwa łożyska RJ4JP-01-08 x2 (lub łożysko oryginalne z Anycubic) oraz Prowadnica liniowa średnica 8mm (długość minimum 400mm), 4 śruby M3x25. ...Proszę użyć orientacji jak na zdjęciu oraz opcji "drukuj płasko" nie wymaga...

The spool holder on the Mega S is quite decent, but its design leaves room for improvement - specifically in how smoothly the roll glides onto the holder and the annoying noise that comes with it. To address these issues, I crafted an adapter that...

... material. ...That's where this handy tool comes in - a limiter for the filament stand that makes sure everything stays stable during printing. ...By using this device, you can improve your filament's stability and get better results from your prints.

... Movement! ...Make sure to attach the sensor using its original bolt. Be cautious when tightening the sensor - don't overdo it or it might become too rigid and lose its flexibility. This way, you'll be able to adjust the filament's path with ease!

I designed a filament roll holder that cleverly avoids interfering with the SD Card slot, allowing for seamless printer operation. ...I'm excited to share this innovative design with you and hope you enjoy it as much as I do!

... allowing it to glide smoothly in and out. To facilitate easy filament loading, simply attach a short length of nylon tube. The tapered joiner comes in handy for connecting additional tubing to a storage box for convenient access to the filament.

Filament Holder Based on Ball Bearings I utilized four available ball bearings as a starting point for this design, which led me to create tubes tailored to their specific dimensions. The holder is designed with two distinct sizes, allowing it to...

Engineered specifically to complement a 3D printed spool holder, it resolves a common issue: the stock location of the filament holder is being disrupted by the spool holder itself. Conveniently, mounting holes for the filament sensor are...

... mount and use a fully threaded 1/2-13 HHCS and capture it with a nut. I use a wing nut to tighten the spool on the holder. PIctured is a 4" bolt, but it didn't work well with a spool that had a smaller ID. I have changed this out for a 5" bolt.

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

This is a filament spool holders for the Anycubic i3 Mega/ Mega S. ...As additional parts are needed: **1)** 3 x M3 [Threaded...

This is a spool holder for the Mega S. It allows a quick change of spool if you don't have many space, for example, if you are using an insulated box. ... I replaced the two M3 screws with two pins because there isn't necessary to lock the holder, but...

Anycubic Filament Feeder Mega.

Filamenthalterung für Anycubic Mega X

Filament dust filter for original Anycubic Mega S filament holder. No screws neccessary. (Clamp it) Quick designed. Printed with PLA. No special settings. ...

Ich habe ein Filament Sensor Halter für den ANYCUBIC I3 Mega S konstruiert, damit man diesen anständig an der Seite befestigen kann. I constructed a filament sensor holder for the ANYCUBIC I3 Mega S so that it can be attached properly to the side. ... ...

Ich habe ein Filament Sensor Halter für den ANYCUBIC I3 Mega S konstruiert, damit man diesen anständig an der Seite befestigen kann. I constructed a filament sensor holder for the ANYCUBIC I3 Mega S so that it can be attached properly to the side.

a filament spool holder adapter for my anycubic mega pro for less friction on the spool.

A Simple Upgrade for the Anycubic Mega's Fixed Filament Sensor The angle of the filament in its original mounting position causes issues with the sensor, often resulting in broken filaments. To address this problem, I created a custom solution using...

This is the clip-on version of the Anycubic i3 Mega S Filament Halter / Holder originally designed and shared by OL_Robin (https://www.thingiverse.com/thing:4505356). Works fine with PLA. Layer height 0.2 mm, Wall thickness: 2 mm. Infill e.g. It...

This is a compact toolbox and filament holder designed specifically for the Anycubic i3 Mega S 3D printer. The original design left me frustrated because I often found myself searching for essential tools near or at the printer, only to realize they...

Anycubic Mega S Top Mount Spool Filament Guide I switched my Mega S over to the MK4 Direct Drive and found the filament all over the place and rubbing up against the spool holder mount. So I designed this filament guide to work with the [Anycubic...

Anycubic Mega S Top Mount Spool Filament Guide I switched my Mega S over to the MK4 Direct Drive and found the filament all over the place and rubbing up against the spool holder mount. So I designed this filament guide to work with the Anycubic...

The filament end sensor as installed on the Anycubic i3 Mega S is a bit of a problem. The filament is always pulled from the inner side of the spool which can lead to jumping filament when it comes from the outer side. These cracking noises are worse...

Spoolholder for the Anycubic i3 Mega 3D Printer. With an outer diameter of 50 millimeters, this spool holder securely attaches to the printer's plate via two screws that need to be removed and then replaced once the holder is in place. Simply reverse...

I lost the tiny centering aid / filament guide thingy that came with my Anycubic Mega S and was pretty bummed to find out that nobody has designed one of those yet. Am I really the only one in desperate need of such a cap / guide / centering aid? ...

Not sure if this will be useful to anyone else, but I had a similar issue with the small cone part of my Anycubic i3 Mega-S extruder. I managed to lose mine for a while and decided to create a replacement. ...When I attempted to pull it out after...

I lost my extruder nozzle and don't found this little piece as a spare part, so I modeled my own. ...Best print it with TPU. It is only for the Mega-S Extruder - maybe some other Anycubic Printer Models use the same Extruder.