anycubic mega s change filament 3d models

------------------------------------------------------------------- Adaptador para la secadora Sunlu filadryer para Anycubic I3 Mega-S. Se engancha en el marco de la impresora. Se necesitan dos conectores (10 o 6 mm) y tubo de teflón . Las partes...

The arm or lever on the extruder of my Anycubic i3 Mega S snapped and I was unable to manually load or unload filament by hand. It appears that the original is pretty fragile and will likely need to be replaced sooner rather than later. This upgrade...

This is a minimal version of the improved hotend for the anycubic i3 mega (https://www.thingiverse.com/thing:2919245). I made this for my i3 mega S because my radial fan was a little to big for a nice fit with the orginal desgin. Further I wanted...

... on Thingiverse. ...The first is 3791392 and the second is 4178350. I'm focusing on creating a leveling system for my Anycubic Mega S 3D printer that incorporates up arrows. ...This will help me achieve precise calibration and improve print quality.

I wanted to install a 60mm LED ringlight on my Anycubic I3 Mega-S printer, so I built an adapter to match the existing screw holes. The Ledring attaches securely with adhesive, and you must connect wires to the second fan's electrical terminals. ...I...

This is a custom designed protective cover for the AnyCubic MEGA S 3D printer's SD card slot, crafted to shield your memory cards from dust and accidental damage. Its sleek design allows easy access to the SD card while keeping it safe from harm.

This is a revised version of Junior_Barnes' Anycubic Mega-S Bed Heater Wire Support remix.\r\n\r\nThe design was reworked to give the cable a smooth curve to the right, resulting in increased stability. ...Two zipties are all that's needed to secure the...

... fan duct from H_Run. ... I created a wrap-around ring with 270° exhaust ducts. I also removed a small cutout, which is why the original did not fit my printer. This remix is for the Anycubic i3 Mega S (2020). ... Printable without any support.

Direct cable access requires modification to the Anycubic i3 Mega's casing. Specifically, the red, green, and black sockets located on the right-hand side need replacement with open-ended cable passages. ...This alteration allows for unimpeded cable...

Simple mounting plates are designed for the Anycubic i3 Mega S. These plates enable users to easily attach components to the spool holder and Z-axis. A total of two, four or six 6x2 magnets are required, which can be sourced from...

better cooling for anycubic Mega-s Replace the metal Cover on the Print Head with This print Designed for two radial fans 4010 on left and right side for better part cooling 5010 or 5020 Axial Fan for Hot End cooling. ... No Firmware upgrade...

This attachment elevates the Anycubic Mega S by 33 millimeters, creating ample space for oversized fans to be installed. A precisely drilled hole accommodates a No. ...8 screw, facilitating secure attachment to the base of the case while allowing the...

... remix of https://www.thingiverse.com/thing:4193861 The original source is designed for 5015 fan and used for https://www.thingiverse.com/thing:3954252. ... In order to reuse Anycubic I3 MEGA-S original fan for direct extruder, mount was re-designed.

[999D](https://www.thingiverse.com/999d/) provided a nice replacement for the extruder lever of an Anycubic i3 Mega S: https://www.thingiverse.com/thing:4248053 This is a remix by cutting the model in half and glued it together afterwards. ...For easier...

I don't like the stock spool holder that comes with the Anycubic i3 Mega S as this one has to much friction. Looking on thingiverse I came across this: design from Novaklast which i like but i wanted some minor changes to it as when you mount this...

Hey, I didn't find an easy way to set the Z-Axis screws on my Anycubic I3 Mega-S Printer, so i designed this simple distancer with different heights that can be used to align the X-Axis parallel to the Print bed. I determined the approximate...

This is an alternative hotend housing for the Anycubic i3 Mega-S. It is mostly based on the silent hotend design by mileshkin but I removed the mounting location for the original parts cooler fan on the left side and put air vents on that side...

... aus und Schützt mein Riemenmotor. Drucker : Anycubic i3 Mega S Unterstützt : ja Füllung : 25% Anmerkungen : Stützstruktur : Tree und X/Y - Abstand der Stützstruktur auf 3mm einstellen !!! ... damit ihr die Stützstruktur ohne Probleme raus bekommt!

Anycubic Mega/S General Mounting SystemMay 21, 2021UPDATEJune 26, 2021-Version 2b added (-v2b.stl) for top-beam-mount. It fits a bit more snuggly.-Added alternative 1 sided versions (-ALT-v2/x.stl) for all mounts.->>>DOWNLOAD...

Redesigned the noisy stock shroud for the Anycubic Mega S. I suggest a 5015 12v blower fan to replace the stock part cooler and printing this part for the blower fan: https://www.thingiverse.com/thing:2800663 I printed this on an Elegoo Mars 2 Pro...

Made a mount for the Mega S on the spool holder to hold the Rpi camera for octopi. ...Just the mount is changed, everything else is the same as SmartBlug's models.

This project is made for anyone wanted a tool-holder specific for Anycubic mega X tool kit, wit a pen case add in.

Modified the frame to fit perfectly around the Anycubic i3 Mega S, ensuring a precise margin and screen size. Mirrored the cover's design so that it can be mounted inside out, creating a seamless look even when the lid is closed - check out the...

This is a spool holder specifically designed for the AnyCubic i3 Mega-S. (And possibly the Mega Pro/Mega X?? .. Looks like they may use the same factory spool holder) What this isn't: This isn't designed to be the smoothest rolling spool holder in...

A tiny seal for the i3 Mega S

As everyone knows the Anycubic i3 Mega S comes equipped with a built-in spool holder. Unfortunately, I've encountered some filament spools with smaller inner diameters and/or larger widths that don't fit on the spool holder. My initial temporary...

Enhance the Anycubic Mega 3D printer by incorporating additional functionality into its existing framework, utilizing the provided screw system to mount a precision caliper and supplementary tools for enhanced versatility. This creative modification...

... holding the bowden tube at an incorrect height, causing it to kink when homing the X-axis. This design aims to secure the bowden tube just above its coupling and keep cables organized on the left side. It's specifically made for the Anycubic Mega S.

The Anycubic Mega S i3 Glue Holder is a sturdy accessory designed to keep your workspace organized and clutter-free. Its compact design fits neatly on the side of the printer, providing easy access to glue sticks and other small items. With its...

I've built an adapter to make this case fit the Anycubic I3 Mega S. You'll need to remove the touchscreen for this to work. Note: This is currently a work in progress, and it's possible that it won't fit perfectly yet. ... Don't print it right now; I...