anycubic kobra vs ender 3 v2 3d models

This is a Wyze camera mount I created for the Anycubic Kobra. Straight forward installation. ...Just insert tabs on an angle and twist gently to lock.

Hier der Link dazu: https://de.anycubic.com/products/modul-zur-materialbrucherkennung-fur-anycubic-kobra?_pos=1&_sid=b97b87c0e&_ss=r Durch den Stabilisator bleibt der Sensor in seiner Position (auch wenn das vermutlich von Anycubic so nicht...

An LED-strip Mount for the Anycubic Kobra. It can be mounted on top of the Kobra and the LED-strip can be glued into the slide. The slide consists of two parts than need to be glued together (use hotglue instead of superglue). After glued together it...

A simple tools organizing holder for my Anycubic Kobra Neo, am sure it would work with Kobra or Korba go as well. No support needed, no screws or glue required, it slots inside the printer rails nicely, can be placed on either side, front or back...

Needed a cover for the always on touchscreen of the Anycubic Kobra since it's always on. ...This was my first CAD endeavor so learned quite a lot and is definitely not perfect BUT I did get to add some flare on it by adding an outline of Arbok since...

EndoCase AnyCubic-Kobra for mounting endoscope cam to nozzle.preload V. a.0.1. ...as test.</p><p>2 add air flow and endo mount</p>

---------------------------------------------------------------------------------------------- A filament guide optimized for the Anycubic Kobra. The guide is screwed on instead of the filament holder. Required are 2 ball bearings of type 608Z,...

Tired of toasting my fingers, I made a bed handle for the Anycubic Kobra. The left and right feature embossed cobra snakes. (I will upload one without the snakes too when I can) The fit is pretty exact so you might need to do a tiny bit of sanding on...

spool diameter: 195mm Parts for Brackets:* 2x spoolbracket.stl 4x centering.stl if not using screws, i recommend to glue them into spoolbracket Parts for Spoolholders [2 Options]: Option 1: https://www.thingiverse.com/thing:5917626 dual-sided...

Modified the original design to accommodate the Anycubic Kobra.There are two files, one you print three of, the other you print one of. </strong>The file you print one of is for the back left corner where there are a few screws and plates that...

Modified the original design to accommodate the Anycubic Kobra. **There are two files, one you print three of, the other you print one of.** The file you print one of is for the back left corner where there are a few screws and plates that...

Tired of toasting my fingers, I made a bed handle for the Anycubic Kobra. The left and right feature embossed cobra snakes. (I will upload one without the snakes too when I can) The fit is pretty exact so you might need to do a tiny bit of sanding on...

This is a remix of another project modified to be able to fit an Anycubic Kobra. The screw hole was also adjusted to be able to accept a 1/4 inch screw. ... I printed it on it's side and it required no supports.

This is a tool rig for the Anycubic Kobra. Two parts are connected with screws. The legs of the base can be reinforced with fum tape. ...Allows you to store: 2 wrenches, a screwdriver, a card reader, a flash drive, wire cutters, a scraper and hex keys.

Remix to fit my Anycubic Kobra. On the right side you can see 4 holes, they are for box with some addition electronic (step down module to reduce extruder fan noise and to supply extruder light. I will post this project lately). ...

Here are some mods for the Anycubic Kobra. They include: 1. Rails of different sizes that fit neatly into the rail slots 2. End cap that can be used to replace the stock end caps (1 on the front and 2 on the back). ... Supports recommended for the...

I couldn't find any online, so this is my first attempt at an object, be kind :) Fits the ends of the tracks on the Anycubic Kobra or any similar printers that use the same parts. Easily slide in and out, allowing you to add a little customized...

I currently use his design for my Vyper and decided I liked it so much that I decided to remix it to be compatible with my Anycubic Kobra Max. Currently, every piece is complete with the exception of the widened platform chain mount. ... This part is...

Da der Anycubic Kobra Max in ein Gehäuse gebaut wurde, mussten eine Umlenkung des Filaments gebaut werden. Hierzu werden lediglich folgende Teile benötigt:1x Kugellager 60031x M5x20 Senkkopfschraube1x M5 Mutter2x M3x25 Schraube2x M3 MutterSince the...

This is a filament guide for the Anycubic Kobra (not Kobra Max).I'm pretty sure this won't help or hurt your prints, its more of an organizational thing. When I started using a bearing aided filament spool holder, the filament would come out in an...

To attach it, you first have to remove the plastic cover with the 'Anycubic Kobra' emblem on it. The mount then simply slides on the metal piece. Usually, the mount should be tight enough to hold on its own, but you can insert a 2x2mm piece in...

... <p>Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=948783 Instructions Using the following options: FrontFaceText = Anycubic TopFaceText = Kobra BottomFaceText = 3D Printer Tolerance = .5 Category: Office

Replacement feet for the Anycubic Kobra Go or Neo. They increase the base feet height by 8mm. The OEM feet for the Kobra Go were 20 mm so these are 28 mm. Use the screws from the old feet to install these. I added a stainless steel washer beneath...

Tool tray for the Anycubic Kobra. Holds all the tools that came with the printer. Slides into the front left rail. The rail end cap can be taken off to expose the rails. A test print for the rail fitment has been included to check your...

This is a filament guide for the Anycubic Kobra (not Kobra Max). I'm pretty sure this won't help or hurt your prints, its more of an organizational thing. When I started using a bearing aided filament spool holder, the filament would come out in...

A simple friction fit collar to shorten the width of the open area on the Anycubic Kobra printers, so that your spool doesn't move all the way out to the side. I found that with the base wide spool holder, my smaller spools liked to "walk" all the...

Ich habe das System vom neuen Anycubic Kobra 2 nicht so gemocht, dass das Filament an der Seite montiert ist. Dafür ist der Filamenthalter, um bis zu 6 4mm Schläuche von wo anders aufzunehmen. Für die Leitung zum Extruder ist die Halterung da, wo...

Beim Anschrauben an den AnyCubic Spulenhalter muss evtl etwas probiert werden, damit der "Arm" halbwegs korrekt ausgerichtet UND fest ist. Das geht aber gut. (Evtl mit Rohrzange festschrauben) Ein Zusammenschnitt aus 2 guten Objekten. Der...

It´s just a little Box for a 20mm diameter switch. ...You can stick it in the foundation of the Kobra and use it for your needs. ... I´m using it for the LED-Arm at my Kobra

LED-Lamp holder for my Anycubc Kobra. ...The LEDs are in a 35*8 aluminium profile.</p>