anycubic kobra usb 3d models

Cap for Anycubic I3 Mega USB port. I integrated a Raspberry PI and a 12V -> 5V DCDC converter, available on Amazon at https://www.amazon.com/dp/B019GX3YP4/, into the printer base. The USB port is internally connected to the RPi with a soldered USB...

Provides a flat surface where to glue a led strip. ...Insert into the holes under the top bar.

Remixed from: https://www.thingiverse.com/thing:5356603/files Thanks jfrog88! CAUTION: Tested with PLA, but you may want to make it from a material that can withstand higher temps. No Supports needed Snaps into place! Tip: Hold...

Here is a handy toolbox to mount on the top rail for storage of the tools and spares that came with the printer. ...There's plenty of room for a pair of sidecutters, etc, so you can keep everything in an unforgettable storage box right on top of your...

Printing-No supports are required. Use a brim on poor bed adhesion surfaces.-You will need to angle the chain 45 degrees to fit.-Keep in mind that this is a print-in-place design, so your clearances need to be tuned well. Assembly-Organise the cables...

This is a remix for those of you that have the Bondtech direct drive upgrade. Also if you have an enclosure this mount will actually line your spools up with the access flap at top. I changed the design in Fusion 360 free version. I am a beginner,...

What you will need: 3x GT2 6mm 20 teeth 8mm hole 1x GT 6mm closed loop belt 600mm 3x bearing 8mm x 22mm x 7mm 1x T8 2mm pitch 4mm lead 450-500mm with nut 1x T8 2mm pitch 4mm lead 400mm 2x M5 40mm 2x M5 washers

This holds a standard 10mm led strip and can be used on any printer with the same head rail. I happened to use 4 sections to fit the Max. The sections are 100mm each, 400mm for the Max. I have the angle slightly to the back to keep the light from...

This is for redirecting the filament feed from the front/left corner of the printer. ...This works great with my filament spool holder.

Need to drill big holes by 2mm, and small by 1.3mm for self-tapping screws. Drilling for fine threaded bolts is not required. Does not require additional parts and bolts. Bolting the turbo fan is optional. Требуется сверловка под саморезы, на...

Print Settings:0.2 mm Layer Height10-20% infillNo Supports

Remixed version of JDBull's minimal filament guide. I wanted it closer to the spool (and center of the rail) so I mirrored it to other side. I also didn't quite like the slit in the original so I created a solid version as well as created a slit...

Short Bed handle so you don't burn yourself. Tested with PLA and it works ok unless your Bed is over 60 degrees C. **PLA - 200 Extruder/60 Bed/25% Infill .28 Resolution** Snaps in place No Supports needed Caution: Bed may melt this...

Ledbar for Ender 3s1 designed to fit Ikea Ledberg ledstrips.Optional endcaps for that clean look.

camera mount with LED lighting and belt cover. ...camera mount for logitech C270 Original Files (https://www.thingiverse.com/thing:5487239)

Hey I made this up really quickly as near the end of the roll my filament would get caught in the Z rod. This requires no tools, I printed it out of PLA+ but regular PLA would work, I did 3 walls, 15% infill. Print it with the shaft pointing...

This piece fits in the tracks under where the nozzle defaults to. This will catch bits that fall off the nozzle and keep them from going under the printer. ... Supports - Yes (I used Tree supports with the bottom on the bed) Infill - 10-20% Layer...

Made with a 0.8 nozzle and TPU (95A)Squish nicely and dampens really good.Simply put it in original feet of the printer. ...No mod required

REMIX from: https://www.thingiverse.com/thing:5357100 Thank you jimsterdelux Fits a 8x16x5mm Bearing which snaps in Need : 2 - M3x10mm Screws PLEASE CHECK OUT my other designs here as I am moving over to Printables and no longer will...

Adjustment from Filament Guide. ... Works fine

I got the end off a model I found somewhere but can't remember where. (Sorry) Since I wanted to run a PTFE tube from my Sunlu dryer to the printer, I made this adapter. It uses the M10 size threaded adapter. I feed the tube all the way through...

I love my cobra very much, but because of the top location of the spool, it seemed very bulky. This is a filament side feed system. Additionally, you will need - M4x10 screw 2 pcs. - nut M4 2 pcs. - screw M3x10 2 pcs. - nut M3 2 pcs. - 608...

What you will need: 3x GT2 6mm 20 teeth 8mm hole 1x GT 6mm closed loop belt 600mm 3x bearing 8mm x 22mm x 7mm 1x T8 2mm pitch 4mm lead 450-500mm with nut 1x T8 2mm pitch 4mm lead 400mm 2x M5 40mm 2x M5 washers

MUST USE TPU if you want these to cushion your printer and dampen vibration. The TPU I used is rated 95A for softness. No supports needed if printed in the correct orientation. The spool footing fits nicely on the bottom where it would normally...

Littlie brush holder to clean nozzle. Connects to front left bed leg. No supports, ABS+. ... My G-code: ```M109 S230 G28 XYZ G0 Z1 G0 Y30 G0 Y0 G0 Y30 G0 Y0 G0 Z10 M104 S0```

A cable holder for the left back side to keep the cable away from moving parts. ... The holder only needs to be clicked into the alluminium profile on the back.

Modification of the reel support bracket, (used to lower it). Beware of tall prints, the extruder can touch the coil. Requires no additional parts and bolts. ... Lower layers: at least 30

Print two sets of shortest rails for the back

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/a8CTiFm4ttx