anycubic kobra troubleshooting 3d models

This is a mount for the LED strip profile. The lighting is controlled by the Zigbee RGB light TuYa TS0503B controller. This allows you to automate the lighting of the printer according to your preferences. The lighting can turn on when the printer is...

Dort ist zwar kein Lüfter, aber wenn alles andere auch gedruckt ist, so muss diese ebenfalls gedruckt werden :)

UPDATE 11.11.2023: added the STL and the texture to a ZIP file for easy download. The texture is now based on the print bed size defined in the settings (420x420) so the grid actually corresponds to 1cm squares.----If you're tired of seeing the...

This is an elevation of the printer to be able to use, for example, a higher power supply and mainboard coverage. Furthermore, the feet stabilize the entire printer, which results in a cleaner print image. The feet are put over the original rubber...

Changed to a partial snap fit (using at least one screw is still recommended) Bunch of tolerance changes from the original, the shroud is 5mm shorter and has redirected ducts, sacrificing the LED for now, and the heatsink fan is also lowered 5mm.the...

0.8mm tolerencesyou may will need to trim the bad overhangprinted with no supports10% infill

This just slips on/off the gantry end cap. You can still adjust the belt. I have yet to adjust focus on this camera so the focal length is off and it's a bit blurry. Remove the pin that holds the original mount on and use this. I used a 3x20 mm screw...

This is my first remix of a piece for my printer, and I made the modification because I couldn't find any mod for the cape fan that I liked, this version is the best so far, I deleted the other 2 because they weren't right, so People do not download...

This just slips on/off the gantry end cap. You can still adjust the belt.. I used a 1/2" 1/4-20 screw and a brass threaded insert. Tree supports may be easier to remove unless you want to change the orientation prior to slicing to best suit you. ...

I remixed this PSU-Cover, to fit in Noctua 80x25mm Fans. The original Part2 is also included here, to download it easier. ... Please read the instructions from the original creator, he made a pretty good job!

This box will fit into standard X-Rails to hold extra pieces of filament/drips.

I Designed this to attach to the two bottom bolts on the print head carriage directly behind the hot end. when installed correctly it will stay just above the tip of the hot end and light the whole area at the print head. I ran the wires for the 2-...

Annoyed by a display that’s too bright and you can’t turn it off? With this dark mode, only two holes remain open to control the temperature while using Octoprint. ...Also protects the display from your cat.Print as you like, I recommend 100% infill and...

The standard psu fan was very loud! I had a few old 92mm 12v fans laying around so this is an adapter to replace the standard psu lid and will house 2 25mm thick 92mm fans. I wired these up in series as the standard fan is 24v. The psu is now barely...

This is a simple remix to swap the mount to the other side, and lengthen the x-distance to accommodate a larger fan on my setup.

I decided to remix my V2 mount so that a Wyze V3 camera could be mounted instead. The mount is designed to fit over the X-axis tensioner so that it will travel up and down with the printhead carriage. It allows for a constant side view of the...

A very dirty remix for mounting the filament guide with runout sensor. I use underprice sensor in less than 1 dollar fron Ali https://www.aliexpress.com/item/1005003397498506.html instead $15 for original sensors. ... Find the way to secure sensor...

Halterung für Filament Runout Sensor, damit dieser um 90° versetzt montiert werden kann. ...Somit kann der Filament Halter oben montiert werden, ohne dass man das Kabel des Sensors neu verlegen muss.

I was getting a lot of dust from hollow and cardboard spools rotating above the plate so I created this to use instead. Makes the spool practically have zero resistance, eliminated cardboard dust and works with plastic spools as well. ...Print the...

<p>Onshape model: https://cad.onshape.com/documents/65ede40b24f5475b03a657b5/w/b61737489ce3883fe20f99e9/e/08067fb49c04efd261b3984d</p>

This is the added, thicker end Z-Axis mount that i mentioned in my "Update" message. The V3 files are 7.5mm thick at the end. They are also rounded to look better. The V4 files are 10mm thick at the end. ...They are also rounded.

Strain relief cable clips for the X-Axis.FreeCAD Version:Link branch FreeCAD - Version: 2024.123.0.14555

I designed this enclosure as a replacement for the original fan, intending to install a more noise-efficient 120mm fan. ...In order to accommodate the larger fan, it's necessary to extend or replace the existing feet.The cover is designed to utilize the...

Once you printed the two piece you will need:-2 M4x8 bolts.-1 M4x30 bolt and nut-2 F688ZZ Flanged Radial Ball Bearings (cheap at Amazon)

<p>This fan duct wraps around on 3 sides to give as much cooling as possible without obstructing the view of the nozzle. There is a thin, removable strip of material spanning the front opening to allow a brim to be used without the brim entering the...

A more streamline and practical take on PTFE-wire clip.A simple PTFE tube - wire clip. Worked better then some other solutions in my case. Looks cleaner.Optimized for 0.8 nozzle. Will work fine with any other.Step and F360 files are also...

I got tired of the two previous versions having a 60 mm offset on x-axis. This is my attempt at remedying that.PLA will work, but PETG is better. ... It might be ugly, but hopefully it works.

This is a remix to add a cable guide for the Z axis. Print the parts as they are. No need for supports. Don't hesitate to ask me if there are any modifications to be made.17 part for Z15 part for XIl s'agit d'un remix pour ajouter un guide-câble pour...