anycubic kobra neo leveling 3d models

*IMPORTANT* Use it together with the Nut and Bolt part from: https://www.printables.com/de/model/417398-kobra-go-x-axis-tensioner For pulley mounting, you will need the m3x16 screw (x1 for each axis) and of course the 20 teeth, bore 3mm width 6mm...

IMPORTANT Use it together with the Nut and Bolt part from: https://www.printables.com/de/model/417357-kobra-go-y-axis-tensioner/files For pulley mounting, you will need the m3x16 screw (x1 for each axis) and of course the 20 teeth, bore 3mm width 6mm...

PEI Bett Position`s Hilfebenötigt noch Doppelseitiges Klebeband

Orginal design by AshhhD remixed by me!Inverted direction of spool roller and added a filament guide that takes a bowden connecter so you can relocate the filament entry point.Supports and brim reccomended

As I didn't have 688 bearings or M4 bolts on hand, I remixed the model for use with 608ZZ bearings and M3 bolts which are more common to purchase in my area. I found that best results are achieved using a rigid stepper motor coupler (the stock one is...

risers for kobra max 210 mm high with tops to avoid movement, it fit in the rails and you can rehuse the same screws to mount the risers.you can modify the high in your slicer but you will need longer screws.

Just reengineered the original Kobra 2 Hotend Housing for Fun. I dont like the original mount of Housing/Duct and Fan because it is very fragile. Here i used 2 M3 Screws (20, 25mm) to hold all in place. You also need 4 threaded inserts. ... Fanduct...

So, I found the exact thing I needed to start with and remixed it.It had to be larger to fit the Kobra screen. I made it a bit loose and attached it to the LCD housing with a bit of double sticky tape. It works perfectly. ...The print in place hinge is...

... model to avoid this problem. Especially for the Anicubic Kobra you'll need: -on the left side 2X 19.5_cm.stl -on the right side 1X 16_cm.stl, 1X 19.5_cm.stl I also left the .f3d file of my model so that you could create your own length and width.

This model adapts the metal carriage of the original Kobra to be able to mount the Voron Stealthburner toolhead. ASA is the recommended material for printing this. 4 walls, 4 tops and bottoms, 25-40% infill. ...You will need four heat set inserts and...

I made it slighty smaller, with some addons like, led stip holder remixed withhttps://www.printables.com/pl/model/709480-anycubic-kobra-2-pro-led-top/filesand fiment guide hole. ...Feel free to download

We made this remix of the Vyper sensor holder to adapt it to the Kobra Max. It lets you print using filament coming from above, as per a top-mounted spool holder or a wall-mounted one. We use the Ikea Skais spool holder to not overcharge the...

Never really cared much for the stock round wiring clip for the hotend wiring ribbon next to the extruder that came with the Kobra Max. You had to crunch it up and roll it to make it fit and do it's job. . This is just a simple flat ribbon support...

Gerade der Kobra "federt" sehr viel. Mit dieser Führung (einfach anstelle des alten Halters mit den gleichen Schrauben befestigen) ist es möglich das Filament von der Seite - oder von oben - z.B. aus einer Drybox heraus an den Extruders zu leiten. ... ...

Someone did a Mainboard cover for the Kobra 2 Max but this didnt fit to mine.So i decided to create my own.Note this cover is for Fan replacement to a Noctua 92mm x 14mm...

Filament guide for the Kobra that snaps onto the top rail by sliding it on from underneath. It was designed to fit the main center section of the top rail but I've also included a freecad project file where it's fully parameterized so you can adjust...

This is a remix of Robertlbrown22 Vyper Kobra OMG direct drive bracket. I modified the design through Tinkercad. I enclosed the slots that sit over the spacers for the wheels and now it sits very securely but i have left the original holes (which...

This was a simple part I did up during the process of repairing a Kobra that I ended up with, after updating the cooling I found that I didn't have a Proximity sensor anymore. In my case I ordered a LJ12A3-4-Z/AX from Ali and installed it. After...

Hello here I leave small utensil that I solved a problem in my kobra plus, I guess it will be valid for all models with the same hotend, the movement of the head in a few days I stopped turning on the light that has the hotend and I realized that by...

Filament guide for the Kobra that snaps onto the top rail by sliding it on from underneath. It was designed to fit the main center section of the top rail but I've also included a freecad project file where it's fully parameterized so you can adjust...

This is remixed (very badly) to fit the Kobra Neo. I'm not a 3D modeler so I did what I could.Seems to work better than stock. ... Supports are only needed for the unsupported ends of the ducts, and if your printer is bad at bridging you might want to...

UPDATE 9-29-2022: Another Kobra user pointed me to this SKU: MF50152VX-1L02C-A99 I purchased this fan and verified it spins all the way down to 1%, so I highly recommend this one! I have also uploaded a v2 of my design!</strong><br><br><strong>UPDATE...

I wanted to build an enclosure and have a direct drive for the new Kobra Max. While the carriage looks nearly the same to the vyper, things are just slightly different so I made some modifications. I also made it in a way where it can be printed...

I snapped the factory Kobra nozzle in the factory heater block so I decided I would just upgrade it with an E3D V6 I had on an old no longer functional printer, of course this demanded a mounting solution which I was unable to find pre-existing.

Used to hold a dial indicator in place while leveling be.

So here my version, its very similar in design but my design uses 2 trapped m3 nuts to make assembly a lot easier than the anycubic version. All that is needed is (2) m3x8 hex button head cap screws, and (2) m3 nuts. I wil also include stl for the...

I have tried a couple of waste bins and tool holders designed to fit the Kobra Plus that actually do not fit (clearance issues) so I decided to take a stab at making one. This was designed in OpenSCAD and I am a total noob with 3d design, but after a...

I have tried a couple of waste bins and tool holders designed to fit the Kobra Plus that actually do not fit (clearance issues) so I decided to take a stab at making one. This was designed in OpenSCAD and I am a total noob with 3d design, but after a...

I designed this bracket to replace the P-Clip that is provided by anycubic to hold the print head cable near the extruder. It never made sense to me that they wanted the flat cable folded over and crammed into that little clip. This bracket uses...

Cover - 1 pcs Support with a loop - 1 pcs Bushings - 2 pcs Logo Anycubic - 1 pcs We print the logo in two layers, the first layer is black, and the second is gray. ...Create a script in Cura to pause after layer 5, change the filament from black to...