anycubic kobra neo camera 3d models
139550 3d models found related to anycubic kobra neo camera.thingiverse
Simple diamond pattern Z-Axis camera mount for the Anycubic Kobra Neo. I used the Camera Mount for Logitech C270 on 2020 Extrusion by NikNolte on Thingiverse: https://www.thingiverse.com/thing:2426231 as reference for creating the base brackets to...
thingiverse
Tried some other Z axis camera mounts for the Kobra Neo and found them to shake and wobble with high speeds and accelerations. So I designed a more rigid mount that seems to perform quite well. There is still some wobble, which could be fixed with a...
thingiverse
This is the added, thicker end Z-Axis mount that i mentioned in my "Update" message. The V3 files are 7.5mm thick at the end. They are also rounded to look better. The V4 files are 10mm thick at the end. ...They are also rounded.
thingiverse
A quick & dirty way of sitting a camera with a lrgerbase on the side of the Kobra Neo. Measurements are taken to allow the front part to slip nicely over the frame on the right hand side & the plate is set far enough back to stop the printhead...
thingiverse
Simple guide to help keep the filament in the center of the print area over the print head on an Anycubic Kobra Neo printer.
thingiverse
This is a remix of the Filament Guide from @tommytwothousand. ... It has been adapted to the Anycubic Kobra Neo, replacing the original spool holder and using the screw threads. ...
thingiverse
anycubic kobra neo height gauge It's used for setting the sensor height to the nozzle height. ...Nozzle touches the lowest part and then you slide the sensor down to touch the
thingiverse
Another filament catcher for the Anycubic Kobra Neo. One of the other files I printed was too large to fit into the rails on my machine so I whipped this one up quickly. This one fits a little loosely so scale it up a tad if you want a snug fit. ...I...
thingiverse
Inspired by other such projects, I decided to use the leftover screws from the 'Tool holder for Anycubic Kobra Neo' project made by 'fatalwir' and create my own waste container.The screws for the holder are M3*10...
thingiverse
... in varying lengths and quantities as indicated in the STL file name (although the 3.875 inch version is the only one that needs four copies). If printed with the Kobra Neo, I have not found there to be any need to apply any bed adhesion settings.
thingiverse
ADXL345 X-Axis and Y axis mounts for the Kobra Neo There's another mount by Applepie2 but it doesn't fit the accelerometer I have which I think seems more commonly available (e.g. https://www.amazon.co.uk/dp/B09M6MSF7J).. There are screw mounts...
thingiverse
... I can make the change. I think the most common heatbreak sub is from the creality cr10, and that one is 27.5mm long. I'll post pictures once it's done printing. It's a "work in progress" once it's printed, mounted, and tested on the Kobra Neo.
thingiverse
A camera mount for the Anycubic Kobra printer. The mount attaches to the z-axis and moves up with the print. To attach it, you first have to remove the plastic cover with the 'Anycubic Kobra' emblem on it. The mount then simply slides on the...
thingiverse
This is a remix of another project modified to be able to fit an Anycubic Kobra. The screw hole was also adjusted to be able to accept a 1/4 inch screw. ... I printed it on it's side and it required no supports.
thingiverse
Camera Holder for the Anycubic KobraThe ball joint is 16mm in diameter and fits perfectly Pi Camera case designed by Sneaks, or as in my case with Pi Camera 3 module,I have used this...
thingiverse
With the Kobra being so new, i had not seen anything really made up for it, and I wanted a Z mounted camera for timlapses. This design fits around the belt tension section, and is made to be held in place with 2 M3 screws, length isn't a huge deal,...
prusaprinters
Also, the left side if moved 2mm more outwards and the hooks are a bit thinner for easier clip in and out.--------This is a clip-on cover for the cable connector that goes to the bed of the Kobra, Kobra Neo and the Kobra Go. The cover is meant to act...
thingiverse
Never lose your Anycubic adapter again with this secure stand that keeps it in place. ...Tested on Anycubic Kobra and Kobra NEO.
thingiverse
This is a spacer designed for the Anycubic Kobra Neo spool holder to accommodate Overture cardboard 1kg spools
thingiverse
This is a bracket to replace tiny plastic wire bracket on Z axis of Anycubic Kobra Neo (maybe suitable to other too). Was created to give cables more organised look. ... Printing time around 50 minutes with 30% cubic infill, PLA.
thingiverse
Height Gauge for AnyCubic Kobra Go & Neo. Since only g-code files were available on the manufacturer's website, I designed identical 3D models of this tool for setting the leveling sensor. ... ...
thingiverse
I have designed this tool holder for all of the tools included with my Anycubic Kobra Neo plus one pair of tweezers and a few memory cards. It's mounted with four M3*10 screws and V profile insert nuts. ... Designed in Solid Edge 2021 Community...
thingiverse
This is a rotatable Anycubic Kobra Neo holder.The 3D bearing data (608zz_mk2_tight) created by BoomZilla1 was multiplied by 1.5 and incorporated.There is room for improvement, but I think it is so-so usable.I use.The yellow parts in the figure are...
thingiverse
This is an LED mount for the Anycubic Kobra Neo and Go. It slots into the top bar with a friction fit and includes a filament guide. There is also a version without the filament guide for the Go. After printing, you can super glue the two pieces...
thingiverse
I created this in order to have a wall-mounted spool holder for my Anycubic Kobra Neo that sits under my desk. I used double-sided gorilla tape to mount it but I can add holes for screws if that is requested. It's designed to use the spool holder...
thingiverse
Cover Custom Hotend pour Anycubic Kobra Neo.Mes améliorations :Meilleure ventilation en façade et latérale ;Changement d'inclinaison des volets d'aérations pour une meilleure réduction de la captation de poussière ;Plus besoin de la visée, elle tient...
thingiverse
A couple of simple mounts designed to attached the new form factor Adafruit ADXL345 to an Anycubic Kobra Neo for measuring required input shaping (although this may also work with the Kobra Go and other similar printer designs). No supports are...
thingiverse
... ...when I first bought the Kobra Neo, i noticed the loom droops and even touches the bed during the first layers. this should provide enough support to get it out of the way. should not need it to be angled upwards. ... will require 2 small zip ties