anycubic kobra max upgrades 3d models

May fit other Anycubic 3D printer models: Kobra Plus, Kobra Max and Vyper. 2 files should be printed in order and most likely need to be lined up. When set up in Cura, I placed Color1 piece down first at 0,0,0 position and then laid Color2...

Just a simple filament guide to avoid tangles. Print with 100% infill for maximum strength but its not necessary. Used zigzag supports for the clip part only. Hole lines up directly over where the filament feeds into the extruder. ... The whole part...

This is used to collect excess material while change the filament

A replacement holder that mounts on the top of the machine, use the long screws provided with the machine.

Everyone knows it, with leftovers or film end without spindle it can happen that it jumps over the holder. ...This protection prevents this, because it is high enough that the filament does not jump.

this is just a simple tray that clips onto the top of the printer

<p><strong>Short version</strong> of Louis's <i>perfect</i> design.&nbsp;</p><p>Personally, I use this short one on the left side for purging. ...If you still have your LCD, this short version will also fit on the right side behind the...

Englisch:Here I have designed a pen holder for you.With the holder you can let your printer draw the whole thing works with many pens with a minimum diameter of 8.4mm.You only have to screw the holder to the right side of your print head (one screw...

Erste Druckversuche, nicht schön aber selten. :-) Layer 34 Farbwechsel auf Gasgrün OVERTURE Matte PLA, 4 obere schichten nehmen. Ich habe 2 wie man sieht zu wenig. Gedruckt mit Octoprint, Pausiert und Farbwechsel gemacht. ...An Besten in Infill...

Simple screen cover for Neo

Damit das Filament nicht immer auf das Gestell des Druckers tropft. ...

Hier ein Cover für das Netzteil ohne die Schutzstreben vor dem Lüfter um den Geräuschpegel zu reduzieren.

I designed this on TinkerCad. ...You can make remixes of it and adjust it as you like.

Print 2 and place them on both sides with the bed centered on them and the print head between them Bring the gantry down to rest on the flat top of the tools Loosen the bed and the gantry connections Tighten in order Bed Rollers Gantry...

This is my design to fit 120 mm fans and 25 mm thick fans of the motherboard and PSU. Just mirror the model if want the single model. I also prepared a 4 feet ready to print. ...Just rotate the feet of the front so that it will fit.

The trash bin was right on. I found a model on thingiverse, but there is a different fixation of the tray. Printing PETG from Eryone with a tray printer. ...240/75 In the grooves of the profile, the tray occurs with an interference fit, just so...

Here you can Mount your Printer at your Table. ...Just put it in and out.

Remix on “Squash Feet (longer)” by Popcorn To use new “Cover Plate for PSU” (https://www.thingiverse.com/thing:5990917) and “Cover Plate for Mainboard” (https://www.thingiverse.com/thing:5990907), you'll need these Feet to lift your 3d printer...

When I attached the original platform mount and the hot end mount, I found that the platform mount would catch on itself if the hot end was going to the far left side on the X axis. I didn't like the angle of the hot end mount, which to me, just was...

Hi everyone, this tool increse the cooling condition. First print the 3 parts, place insert nut´s M2-M3 and screws and have fun. ... add new fans: 2x WINSINN 5015 fan 24V 2.4 W 1x WINSINN 5010 fan 24V 2.4 W

1. Нужно нарастить провода. 4 управляющийх провода и 1 заземления. Добавить 0,5м. 2. Длина тефлоновой трубки приблизительно 97,5-100мм 3. Нужно заменить положение катушки с пластиком. ...Располагать необходимо сверху на раме.

Mainboard cover for use with 92mm fan. ... V2 corrected some spacing.

This is remix of remix https://www.printables.com/model/358674-wip-anycubic-kobra-5015-fan-3-sided-part-cooling-d

If you upgrade your Kobra max or vyper to direct drive using the OMG extruder and keep the stock motor this mount allows you to mount the run-out sensor to the extruder. ...You'll need to use an M3 heat-set insert pressed into the mount and the stock...

Remix of "Raspberry Pi Camera Holder for Anycubic Kobra by Dosimo": https://www.thingiverse.com/thing:5805884 - changed the holder to fit the Kobra 2 - increased hole size to 3.1 mm to fit a 3mm screw - front file is unchanged

I adapted it to the standart Anycubic Kobra Neo print surface by changing the color, changing placement of the writing and adjusting the writing. ...I also modified the 3d model.

This is a remix of an upgraded fan duct i found on printables, https://www.printables.com/model/378928-anycubic-kobra-neo-fan-duct. The endoscope camera that i used can be found on amazon,...