anycubic kobra max upgrades 3d models

Raspberry pi + PiTFT50 screen mount on the Anycubic Kobra Go. It attaches to 4040 extrusion Printed it using 3 perimeters and 15% gyroid fill. ...

A belt tension gage created for the Anycubic Kobra Go If interested check out the video instructions on Youtube channel named mrmrsmiley

This is a Bed Alignment guide for the AnyCubic Kobra 2 Plus.May Damage Foam Under Print Bedprinted using Prusa Slicer:No Raft3x Skirt5% infill

Wrap around angled dual duct for a 5015 blower fan for equal flow for the Anycubic Kobra Standard See Print Settings for Info.

This is a replacement knob/dial for the Anycubic Kobra Go. ...This knob adds fins to it for more simple manipulation.

BeschreibungLED Light Bar Holder for Anycubic Kobra 2 Pro.You need this LED Light Bar (308mm): https://www.amazon.de/gp/product/B07DPJ1KXC/ref=ppx_yo_dt_b_asin_title_o01_s01?ie=UTF8&psc=1Print SettingsPrinter:Anycubic Kobra 2 ProRafts:Doesn't...

I needed a way to route filament over the top of my kobra max due to converting to direct drive.

Brackets for mounting a Ikea Dioder to your Anycubic Kobra. Tired to match the design of the Kobra and keep it as light as possible. The pins and clips are designed to be a tight fit, so maybe you need to scale up or down, depending on the...

This remix of pascalmakes pen holder was changed for the Anycubic Kobra. It is attached using holes and screws already used for the Kobra. It can be used with the various tool holders from the original thing. May require slight sanding on the tool...

Z-Axis Stabilizer for the Anycubic Kobra. There is no need to take off or loosen the Z-Axis. ... Other Parts needed are 2 M4x40 Screws and a 608 Bearing

This is my version of v-slot Covers for Anycubic Kobra Go.There are v-slot Cover for all sides except to cover screws. This way you dont have to remove them to tighen the screws.

This is my design for my anycubic kobra go printer because I wanted to convert it to a direct drive drive.It is easier to mount because you just have to slide the other to the roller

This is a bracket to replace tiny plastic wire bracket on Z axis of Anycubic Kobra Neo (maybe suitable to other too). Was created to give cables more organised look. ... Printing time around 50 minutes with 30% cubic infill, PLA.

Dies ist eine Erweiterung des Filamentsensors an meinem Anycubic Kobra 2 pro. Es verhindert daß zu "dickes" Filament eingezogen wird und somit der ganze Druck unbrauchbar wird. ...Ein zusätzlicher, in Reihe geschalteter Microschalter wird benötigt.

This is a camera holder for the Anycubic Kobra. It simply slides on the right side of the z achsis so it moves up and down with your printhead. ...

This is a cable clip for the Anycubic Kobra Plus. ... I printed without a Brim, but I reduced my printing speeds so it did not knock off the bed.

This is Z-axis Guide used for Anycubic Kobra Go.One bearing (MR608ZZ Outer diameter 22mm x inner diameter 8mm x width 7mm) will be used, so please have it ready.

A fixed mount designed for Anycubic Kobra Max to hold a Phaetus Rapido UHF on the original LeviQ probe area. No support needed, I went with 60% infill PETG but you could probably use less. Unscrew the 2 screws that is holding the groove mount...

These models serve as effective solutions for integrating the accelerometer, in order to measure resonances and implement input shaping with the Klipper firmware on the Anycubic Kobra 2 Neo 3D printers.Inspired by classic models available online, I...

This is a holder for a wyze cam V3 for the kobra max, hope this help you to monitor your prints.

A remix from a cooling duct found on printables https://www.printables.com/model/214808-anycubic-kobra-cooling-fan-duct Based on the 2mm offset design found on printables which you have to cut down the left side for it to fit the Anycubic Kobra. I...

You also cannot buy it from anycubic from their store at least (whithout buying the whole replacement print head)On my very first print of the Kobra 2 max, i set it to go and went to sleep. Woke up to the whole print head encased in plastic. I was...

This is a Custom made filament spool holder for the Anycubic Kobra 2,it can be screwed into the 2 pre installed inserts, I used 2 Screws from the printer's power supply bracket, see the screws original location in the image provided (I think they are...

A tensioner for the Z belt on the Anycubic Kobra 2 to help minimize the backlash on the right z screw. ... Uses 2x M4x16, 2x M5x20 and 1x M3x50SCHS screws, 1x M3 nut and 4x 625zz bearings and 2x spacers from 2x v-groove wheels.

I found that my Anycubic Kobra 2 Pro printer moved around way too much on the surface it was on, occasionally resulting is misaligned prints. 30 minutes with a caliper and SketchUp resulted in these little “socks” / leg holders that fit snugly over...

A mount I created to fit the genuine ed3 titan aero to the Anycubic Kobra to get rid of the clone. All you need is 3 m3 melt in thread inserts. print in petg or abs the extruder get pretty warm and will warp. ... Also included is a fan duct to fit...

I have designed this tool holder for all of the tools included with my Anycubic Kobra Neo plus one pair of tweezers and a few memory cards. It's mounted with four M3*10 screws and V profile insert nuts. ... Designed in Solid Edge 2021 Community...

This is for the Anycubic Kobra standard. The small one. This is an adapter for a popular friction-less spool holder. It allows you to use the oem location and spool holder. ... The original spool holder can be found here: ...

This is the perfect way to allow your Anycubic Kobra to hold two filament spools at once! Works well in tight spots and allows for quick and easy filament changes! ... Super easy installation Just remove the original spool holder cap and replace it...

Minimal, adjustable Z belt tensioner for the Anycubic Kobra 2. Attaches to one of the unused M4 threads on top of the frame. Requires a common 608 (8 mm x 22 mm x 7 mm) bearing, as well as a M4 x 8 bolt, a M4 x 30, and a M4 nut. ...Takes out the slack...