anycubic kobra max tuning 3d models

This will adapt a pad 7 to the front of a bigtreetech pad7. ...You will need to swap belt tensioners out for this...

Adaptateur sunlu pour bouteille de remplissage automatique Anycubic M3 Max

Door handle for Anycubic 4 Max Pro printer.

Scaled this down to fit the AnyCubic Max Pro X-Axis adjustment housing.

The K15 Diesel was designed to fit the Anycubic Kobra Max and the Anycubic Vyper. The front plate attaches with M3 screws and the shroud connects to the base with with factory screws.</p> <p>Comes with two face plates. ...One with led mount and one...

The K15 Diesel was designed to fit the Anycubic Kobra Max and the Anycubic Vyper. The front plate attaches with M3 screws and the shroud connects to the base with with factory screws. Comes with two face plates. One with led mount and one...

This opening is 40mm so it fits the anycubic sized resin bottles, i am currently making a larger version that will support the larger mouthed bottles like siraya tech. My plan is to add an insert so the one support could be used for any size. ... ...

This opening is 40mm so it fits the anycubic sized resin bottles, i am currently making a larger version that will support the larger mouthed bottles like siraya tech. My plan is to add an insert so the one support could be used for any size. ... ...

I recently purchased the Anycubic Photon M3 Max and couldn't find a lid online. I remixed the mono X lid from Nicolasfromparis with the following changes: 1) Modified size to dimension of M3 Max Vat, including curve out to pour spout on the vat where...

This design is a Z axis leveling support compatible with the Anycubic Kobra measurements to facilitate the adjustment of the eccentric nuts and avoid printing problems. ... Este diseño es un soporte de nivelación del eje Z compatible con las medidas de...

A marvellous piece of out-of-the-box thinking, impressive engineering!Best thing is: the logic works with the Anycubic Kobra 2 Max without touching the firmware, just connect it instead of the original sensor. This version of the smart spool holder...

Not my design Based off of https://www.printables.com/model/221379-nozzle-holder-v-slot-built-in-m6-threads/files I simply elongated it to utilize the entire space in the Support Slot of the Anycubic Kobra Plus

Note: The Kobra Max and the Vyper use one fan header for both part cooling fans so you will need to splice the two 5015 together. The led on the Kobra can be cut and run through the hole directly under the heat sink fan, or hot glued or super glued...

... I used Octoprint to verify my leveling. Print Settings Printer: Anycubic Kobra Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0,2mm Infill: Thunder/Lightning Filament: Anycubic PLA Black Category: 3D Printer Accessories

My point of view on the model “Anycubic Kobra Z Axis Stabilizer” by Wavz3D https://www.thingiverse.com/thing:5441075 A little bit more reinforced (to avoid crashes in the screw hole) Axis Stabilizer that supports 8x22x7 bearing with opportunity to...

После печати всех деталей набора и сборки на моем принтере Anycubic Kobra Go, стало понятно, что одного переходного кронштейна недостаточно для обеспечения жесткости кремпления печатной головки принтера. После недолгих размышлений я решил...

Anycubic Kobra Go! For greatly increased coverage of airflow around nozzle for part cooling fan. You'll be able to replace your original print head housing with this exposed print head setup using only the original screws. SETTINGS: Slice the model...

this is for an Anycubic Kobra Neo that is doing a dual z axis upgrade using a belt, not dual motors.The benefit of belts is that you never have to deal with synchronizing motors / heights of the X gantry or adjusting the vref on your board, leading...

This clamps on to the spool holder on the Kobra 2 Neo, and I assume other Kobra models with a 25mm circle in the holder. ... the ideal hardware is a 25mm m4 bolts, but any 1/8 inch bolt will work with a washer.

You will also need to remove the 'tail' that is incorporated in Anycubic's filament sensor. To remove the tail, you need only split the casing of the filament sensor (it's super easy) and then, after removal, press the casing back together. Attach...

Anycobic Kobra (Neo) Z-Axis stabilizer STLs split in 3 parts (1-3) and in 2 parts (3-4) You´ll need a 688 2RS TN 8x16x5 mm bearing and 2 M3-M4 bolts with a minimum length of 45mm. If you print optimal, you don't need nuts necessarily (hole is .2mm...

I would like to share a new guide for the max to change the position of the filament to front of the printer .it also guides the filament when going to max height .

made a quick tunning cap for my striker and thought id post it as a remix since i started with the 17f fps cap from this post

After that, it is down to a max Variation of 0.23mm. So the Firstlayer is pretty awesome now. Just print 2 of the supports, bring the Printhead in the middle of the Bed and support it with the supports directly left and right of the head. ...

Leider noch ein Filament Abroller. Ich habe viele Seiten und Downloads mir angesehen um meinem Drucker einen Filament Abroller zu spendieren. Irgendwie habe ich nicht das richtige für mich gefunden. Kriterien waren eigendlich nicht Anspruchsvoll.

A complete redesign of my first dampening feet with an adjustable feet hight. Missing is just a clip to fix the feet to the printer base. ... If you like this feet, please leave me a like.

I found that using the original trash bin resulted in a lot of filaments missing it at the back end of it. So all I did was extend it out about an inch on that end. I used 3D Builder with the original so when it prints there is a visible line where...

I designed this mounting plate after i decided to use old mobile phone for Octoprint. To complete I printed GoPro Arms 2x55mm 1x55mm Twist 1x100mm thx to https://www.thingiverse.com/thing:3312779 for the Arms. ... Parts M5x20mm Bolt ( Round Head -...

For the assembly you will need:2x M5 40mm screws (not M6)688zz bearingThis design is intended to reduce z-wobble on my new 3d printer. ...It's my first design i upload to thingiverse.For the version 2.1 i have fixed the polygonal mesh of the assembled...

Einfache Montage mit der Originalen Schraube für den Hotendhalter