anycubic kobra led light 3d models

Remixed version of JDBull's minimal filament guide. I wanted it closer to the spool (and center of the rail) so I mirrored it to other side. I also didn't quite like the slit in the original so I created a solid version as well as created a slit...

I saw some other filament guides on here and wanted to make something similar. This is what I came up with. It's actually my first attempt at a print-in-place moving part and it worked, so that's pretty sweet. It clips onto the spool holder. The...

This piece fits in the tracks under where the nozzle defaults to. This will catch bits that fall off the nozzle and keep them from going under the printer. ... Supports - Yes (I used Tree supports with the bottom on the bed) Infill - 10-20% Layer...

Made with a 0.8 nozzle and TPU (95A)Squish nicely and dampens really good.Simply put it in original feet of the printer. ...No mod required

Here is a handy toolbox to mount on the top rail for storage of the tools and spares that came with the printer. ...There's plenty of room for a pair of sidecutters, etc, so you can keep everything in an unforgettable storage box right on top of your...

Adjustment from Filament Guide. ... Works fine

The 3mf file is Cura Project with all printer settings.

This is a work in progress, i have not printed it yet but will update if needed.

REMIX from: https://www.thingiverse.com/thing:5357100 Thank you jimsterdelux Fits a 8x16x5mm Bearing which snaps in Need : 2 - M3x10mm Screws PLEASE CHECK OUT my other designs here as I am moving over to Printables and no longer will...

Print Settings:0.2 mm Layer Height10-20% infillNo Supports

Just a simple camera mount. The camera can be placed on top. ...I will revise this form in a timely manner so that the camera can be attached with a screw and the cables have a guide.

This is a VERY snug fit and actually took some fairly decent smacks with the palm of my hand to get it to snap into place. You might want to modify it to make the protrusions a tad narrower. ...Insert the top one first then the side one.

Remixed from: https://www.thingiverse.com/thing:5356603/files Thanks jfrog88! CAUTION: Tested with PLA, but you may want to make it from a material that can withstand higher temps. No Supports needed Snaps into place! Tip: Hold...

Short Bed handle so you don't burn yourself. Tested with PLA and it works ok unless your Bed is over 60 degrees C. **PLA - 200 Extruder/60 Bed/25% Infill .28 Resolution** Snaps in place No Supports needed Caution: Bed may melt this...

Ledbar for Ender 3s1 designed to fit Ikea Ledberg ledstrips.Optional endcaps for that clean look.

Print two sets of shortest rails for the back

Top Mount Camera Holder. ...The camera could be screwed or taped in place.Heavy camera → MoreAs long as your camera isn't too big, the cable from the extruder shouldn't touch it.You can put the cable through the filament holder and put it in the USB...

A cable holder for the left back side to keep the cable away from moving parts. ... The holder only needs to be clicked into the alluminium profile on the back.

MUST USE TPU if you want these to cushion your printer and dampen vibration. The TPU I used is rated 95A for softness. No supports needed if printed in the correct orientation. The spool footing fits nicely on the bottom where it would normally...

This is for redirecting the filament feed from the front/left corner of the printer. ...This works great with my filament spool holder.

Modification of the reel support bracket, (used to lower it). Beware of tall prints, the extruder can touch the coil. Requires no additional parts and bolts. ... Lower layers: at least 30

Printing-No supports are required. Use a brim on poor bed adhesion surfaces.-You will need to angle the chain 45 degrees to fit.-Keep in mind that this is a print-in-place design, so your clearances need to be tuned well. Assembly-Organise the cables...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/a8CTiFm4ttx

Hey I made this up really quickly as near the end of the roll my filament would get caught in the Z rod. This requires no tools, I printed it out of PLA+ but regular PLA would work, I did 3 walls, 15% infill. Print it with the shaft pointing...

Littlie brush holder to clean nozzle. Connects to front left bed leg. No supports, ABS+. ... My G-code: ```M109 S230 G28 XYZ G0 Z1 G0 Y30 G0 Y0 G0 Y30 G0 Y0 G0 Z10 M104 S0```

I got the end off a model I found somewhere but can't remember where. (Sorry) Since I wanted to run a PTFE tube from my Sunlu dryer to the printer, I made this adapter. It uses the M10 size threaded adapter. I feed the tube all the way through...

Remix of Profile Clip from Thing https://www.thingiverse.com/thing:5751605

I love my cobra very much, but because of the top location of the spool, it seemed very bulky. This is a filament side feed system. Additionally, you will need - M4x10 screw 2 pcs. - nut M4 2 pcs. - screw M3x10 2 pcs. - nut M3 2 pcs. - 608...

Es verbessert etwas das abrollen der Spool und führt das PLA sauber zum Druckkopf. Das Loch im Träger war bereits vorhanden. und ist eigentlich für den Filamentsensor gedacht.Ich habe zu Befestigung eine Einschmelzgewinde Buchse M3 verwendet. Die...