anycubic kobra go vs ender 3 v2 3d models
886965 3d models found related to anycubic kobra go vs ender 3 v2.thingiverse
Replacement feet for the Anycubic Kobra Go or Neo. They increase the base feet height by 8mm. The OEM feet for the Kobra Go were 20 mm so these are 28 mm. Use the screws from the old feet to install these. I added a stainless steel washer beneath...
thingiverse
This guide created for Anycubic Kobra Go and use with bearing U623ZZ
prusaprinters
Dies ist eine Halterung zum umbau des Anycubic Kobra Go auf einen Direct Extruder, Bei Fragen zum zusammenbau oder anderem schreibts in die Kommentare Viel Spaß
thingiverse
I didn't see any screen covers specifically for the Anycubic Kobra Go, so I made one. The screen is rather bright at night, so I wanted something to cover it with. I made one with vase mode/spiralize contour and it came out perfect. ...My first post!
thingiverse
Filament roller guide for Anycubic Kobra Go. you can see where the filament was being scraped from the extreme angle. You will need a standard bearing and a screw. The tolerance is tight so my screws threaded in. Will get a nut when needed. All...
thingiverse
After assembling my new Anycubic Kobra Go and testing it, a problem with the z-axis while leveling started to come up.I've tried everything, even dis- and reassembling the whole z-axis with no success.I noticed early on that the antibacklash nut...
thingiverse
The main two are that it is compatible with mounting directly to the frame of the Kobra Go printer, and it is made to fit the arducam OV5647. Other than that this set is assembled exactly as seen in the original model. I assembled the extension...
thingiverse
This is remix of remix https://www.printables.com/model/358674-wip-anycubic-kobra-5015-fan-3-sided-part-cooling-d
thingiverse
... ... This requires no tools, I printed it out of PLA+ but regular PLA would work, I did 3 walls, 15% infill. Print it with the shaft pointing up, and with support for the two 'nubs' The nubs will go in the holes at the top, they just press in. ...
prusaprinters
Also, the left side if moved 2mm more outwards and the hooks are a bit thinner for easier clip in and out.--------This is a clip-on cover for the cable connector that goes to the bed of the Kobra, Kobra Neo and the Kobra Go. The cover is meant to act...
thingiverse
Raspberry pi + PiTFT50 screen mount on the Anycubic Kobra Go. It attaches to 4040 extrusion Printed it using 3 perimeters and 15% gyroid fill. ...
thingiverse
Trash bin for Anycubic Kobra Go to be placed under the extruder home position.
thingiverse
A belt tension gage created for the Anycubic Kobra Go If interested check out the video instructions on Youtube channel named mrmrsmiley
thingiverse
This is a replacement knob/dial for the Anycubic Kobra Go. ...This knob adds fins to it for more simple manipulation.
prusaprinters
This is my version of v-slot Covers for Anycubic Kobra Go.There are v-slot Cover for all sides except to cover screws. This way you dont have to remove them to tighen the screws.
thingiverse
This is Z-axis Guide used for Anycubic Kobra Go.One bearing (MR608ZZ Outer diameter 22mm x inner diameter 8mm x width 7mm) will be used, so please have it ready.
thingiverse
This is my design for my anycubic kobra go printer because I wanted to convert it to a direct drive drive.It is easier to mount because you just have to slide the other to the roller
thingiverse
Height Gauge for AnyCubic Kobra Go & Neo. Since only g-code files were available on the manufacturer's website, I designed identical 3D models of this tool for setting the leveling sensor. ... ...
thingiverse
This is an LED mount for the Anycubic Kobra Neo and Go. It slots into the top bar with a friction fit and includes a filament guide. There is also a version without the filament guide for the Go. After printing, you can super glue the two pieces...
prusaprinters
It was designed to hold two Noctua 40mm x 20mm fans instead of the OEM 40x10 fan and OEM blower.Warning : The Anycubic Kobra Go uses 24V only. Noctua fans are 12V. You will need to use 24V fans, or supply 12V to the fans, otherwise it won't work.The...
thingiverse
Watch here: https://www.thingiverse.com/thing:5894002 Composed these feet from the Kobra Go Foot Block https://www.thingiverse.com/thing:5817375 and the Higher Feet Vibration Dampening https://www.thingiverse.com/thing:5566982 . You need to print...
thingiverse
I snapped the factory Kobra nozzle in the factory heater block so I decided I would just upgrade it with an E3D V6 I had on an old no longer functional printer, of course this demanded a mounting solution which I was unable to find pre-existing.
prusaprinters
UPDATE Feb 6 2023Tweaked 5015 duct to align better with the nozzle. This is a remix of kevinakasam's FrankEnstein duct originally for the Ender 3. (https://github.com/kevinakasam/FrankEnstein-Duct) I have not printed this exact version yet (added a...
thingiverse
I wanted to keep my filament on shelves beside the printer (on a Tush++) not on the top-heavy support holder provided by Anycubic. This guide helps filament across and directs down towards the extruder filament guide. The small guidewheel is...
thingiverse
(look at picture 2) The camera is mounted with 4 M2x12 screws and 4 M2 washers (I used M2x16 screws and M2 nuts, but that's not necessary.) This mount was designed for the Raspberry Pi Camera 3 Wide Angle, but it should work with all versions of the...
thingiverse
V2 of the Kobra and Kobra 2 fan duct. Forward facing duct. Helps when having issues with bed temps and you next to a wall in my case. ...Comment if you print and let me know if it works for you.