anycubic kobra filament guide 3d models

The mind stone is hollow and made from IC3D R-PETG Raspberry Blue filament. It looks awesome and lets the light come through nicely.Printing Tips:For best outside appearance, I printed the 3 handle portions vertically. I used tree supports for hollow...

I have raised my tophat by 20mm which gives the cabling and filament tube plenty of room to breathe. The shroud fits a 3010 hotend fan or a 3007 fan by using a clip-in adapter.This Orbiter 2.0 Mini Stealth is a better fit than the Orbiter 1.5 Mini...

On your Prusa MK3/s you must release a lot of the tension on the extruder gears or you will have issues with the filament getting tangled around the BondTech gears. Also you need to keep in mind that TPU will adhere to the print bed, and the smooth...

It shouldn't be neccecary as all other parts are designed with either "bridges" or a 45 degree overhang. "first-digit-dial" and "second-digit-dial" are designed to be layered with two different filament colors, it isn't required but it makes the...

55 gRequired hardware1 x axial ball bearings 51105 25x42x11 mm (kugellager-express)2 x ball bearings 608 (kugellager-express)slightly under 50 mm - M8 threaded rod (schraubenking)2 x M8 nut - DIN 439 (schraubenking)Assembly: 4 x - 5x30 mm chipboard...

You can us anything from an Exacto knife or a file to clean out the bit of filament covering it. I found a sharp, long, thin, knife to be the easiest to use (You may have something in your kitchen. Don't tell my wife). Then I cleaned it up a bit with...

This takes a full roll of filament or more to print. Each side of the cube takes me 12-13 hours to print on my machine. You need to print nice and slow. If you go to fast, the path wall get distorted on the end and the ball won't fit. You'll also...

I’d love to continue iterating the design based on feedback.Print instructionsPrint SettingsPrinter: Custom KosselResolution: 0.2mm or finerInfill: 15%Filament: AnyNotes:Gently-sloped overhangs, tiny bridges, and few sharp corners make this an easy...

If you love wasting time and filament on support structures, sanding, and finishing, this is the version for you! (Masochist!) If you want something easier, you'll want to wait for the two-piece model. Trust me, it'll be just as awesome, waste less...

Print time is about 9hrs 45mins, and uses about 90g (30.5m) of filament. Printer: Prusa i3 MK3S Rafts: No Supports: Yes, but on baseplate only Resolution: 0.2mm Infill: 20%-25% Perimeters: 2 to 3 After printing, one of the long M3 screws can be used...

A wireless gamepad/controller option is enabled by fitting a holder for a USB ‘dongle’, plus an ultrasonic sensor and an OLED are also fitted to the robot to sense nearby objects and to display the current ‘status’ of the robot.It should be noted...

It was meant to add stability, but I don’t think it does that much but helps with looks.  Doors and drawers assemblyFor the doors there will be a little bit of filament in the slot for the hinge pin that I cut out with a knife and/or use a...

with LW-PLA filament. For a wing printed in standard PLA, I don't think the center of gravity is still halfway reasonably achievable. The motor I used is an Extron 2220/12. It has an outer diameter of 28 mm and fits the motor bulkhead exactly...

You will need the following new screws to attach to the frame:3x M3 12mm screws3x M3 hex nuts See my newremix below that removes 2 sides of the triangle and takes less than half the time to print! Please check out the assembly instructions with...

You loose some of its capabalities and strenght but you save on filament and printing time.(I suggest you try them and chose the one that suit you the most…all are equally compatible with all the terrain tiles…except the last one of...

Since many of my friends own the 18V Makita battery system I thought of a practical Christmas present for them.I got the idea for the basic platform from user "bitplusatoms" with his design "Makita Battery Mount"...

 See also my sunshade for the FeelWorld 5 ½" Field Monitor at:https://www.printables.com/model/240027-feelworld-fw568-5-12-inch-field-monitor-shadeAs you can see from the last photo, the whole rig (without follow-focus and camera) compresses...

Do note that 116 tiles are quite a lot of models to print - If you intend to print up an entire set, expect to devote a lot of printing time and filament/resin to the project. A single tile printed at high settings takes approximately 1.5 hours to...

(you could play with Z0mm but then you're guessing on the height and may be crashing the hot end into the bed) Which then means that when we use a 0.04mm layer height, or a 0.4mm layer height, we have accuracy that the extruded filament is going to...

After making the twisted wire, I would strongly suggest wrapping each pair onto an empty filament spool to make them more manageable. This stuff loves to tangle and kink, and any kinks will be visible after wrapping. Before wrapping the handle, test...

Do note that 116 tiles are quite a lot of models to print - If you intend to print up an entire set, expect to devote a lot of printing time and filament/resin to the project. A single tile printed at high settings takes approximately 1.5 hours to...

it's a very nice platform. Parts list: PLA, any brand I guess, but I used Prusament one Raspberry Pi 4 two SATA Hard Disk Drives two very short SATA USB cables with thin connectors, I used a Sabrent model (see below) one 4mm NF-A4x10 5V Noctua fan...

I guess it could be printed with PETG too, but for me nothing beats the look and the sturdiness of Prusaments PC-Carbon Fiber.The 100mm Filter Holder should be printed in TPU or other flexible filament to avoid scratching your 100mm filter! I used...

The minute arc is designed to have the filament color changed near the end of its print (included in gcode), so the minute figures stand out. The typeface is the excellent <a href="https://fonts.google.com/specimen/Voltaire">Voltaire</a> by Yvonne...

Primary fan is here, secondary is here.&nbsp;For this, you will need:1x 4020/10 case fan2x 4010 blower fanAn ample amount of filamentan H2 with 4 M3 screws for full mounting12x M4 screws to attach to the bearing blocksa SuperPINDA (or any 8mm...

The only really important thing you need to consider when choosing the filament and print settings is that you need to use the same material (not color) as you will use for the last and final print, and you need to be able to glue the sand parts to...

or 10 x 3 mm [example 3/8](https://totalelement.com/collections/disc-magnets/products/3-8-x-1-8-inch-neodymium-rare-earth-disc-magnets-n48-30-pack) I would get N42 since I find N48 too strong for this application + 2x knurled thumbscrews with M3 x...

If you have the proper filament colors, no painting is needed. The assembled model is 175mm tall, 315mm long and is mostly in proportion to my previously released Looney Tunes models. Enjoy! ...

At first I made the box where it could be printed in one go but my printer kept giving me grief and I lost a lot of filament. So instead, I broke down all the walls individually so they could be printed one wall at a time and then glued together. ...

Edit: I have updated the base files, extending the pattern to the edges more and making the central pattern better for filament swap multicolour printing. For the box you will need to print: 1x 'Body', 1x 'Base', 1x 'Internal collar', 1x 'Twist...