anycubic kobra filament guide 3d models

EndoCase AnyCubic-Kobra for mounting endoscope cam to nozzle.preload V. a.0.1. ...as test.</p><p>2 add air flow and endo mount</p>

For my Anycubic i3 Mega, I employ a customized filament holder that clicks into place precisely where it should instead of relying on the separate original holder, which I despise. The original holder often causes issues, even when used, as the...

Ich habe das System vom neuen Anycubic Kobra 2 nicht so gemocht, dass das Filament an der Seite montiert ist. Dafür ist der Filamenthalter, um bis zu 6 4mm Schläuche von wo anders aufzunehmen. Für die Leitung zum Extruder ist die Halterung da, wo...

These things are specifically designed for use on the filament at the Anycubic i3 Mega site or located at the very top of this particular 3D printer model.

Modified the original design to accommodate the Anycubic Kobra.There are two files, one you print three of, the other you print one of. </strong>The file you print one of is for the back left corner where there are a few screws and plates that...

UPDATE 07.08.2023 added two new parts (not tested yet!): endcap_duo_simplifiedx70mm (for “holder+20mm”) endcap_duo_simplifiedx90mm (for “holder”) these allow the spoolbracket to be mounted on the anycubic kobra plus aswell. See therefor:...

Also has a strain relief for the tubeWhen not using the Palette, the bracket works fine for bare filament.You will need to clip off the filament sensor bracket and mount the sensor to this bracket.Parts needed:2x M3x25 Screws, Nuts, and WashersPrint...

This is the Easy Install Removal Center Bearing Filament Guide with 2020 Clip for simple setup and teardown.

Just wanted a great articulating filament guide Could not find anything that worked so make my own

Remix to fit my Anycubic Kobra. On the right side you can see 4 holes, they are for box with some addition electronic (step down module to reduce extruder fan noise and to supply extruder light. I will post this project lately). ...

I couldn't find any online, so this is my first attempt at an object, be kind :) Fits the ends of the tracks on the Anycubic Kobra or any similar printers that use the same parts. Easily slide in and out, allowing you to add a little customized...

This is a mount for a LED strip for the anycubic kobra printhead, it works really well to light op the printing area, It does not need any screws, just clicks into place with the 3 taps i used a 24v LED strip that is 1cm wide and 5 cm long

This is a remix of another project modified to be able to fit an Anycubic Kobra. The screw hole was also adjusted to be able to accept a 1/4 inch screw. ... I printed it on it's side and it required no supports.

This is a tool rig for the Anycubic Kobra. Two parts are connected with screws. The legs of the base can be reinforced with fum tape. ...Allows you to store: 2 wrenches, a screwdriver, a card reader, a flash drive, wire cutters, a scraper and hex keys.

Here are some mods for the Anycubic Kobra. They include: 1. Rails of different sizes that fit neatly into the rail slots 2. End cap that can be used to replace the stock end caps (1 on the front and 2 on the back). ... Supports recommended for the...

I currently use his design for my Vyper and decided I liked it so much that I decided to remix it to be compatible with my Anycubic Kobra Max. Currently, every piece is complete with the exception of the widened platform chain mount. ... This part is...

**If you don't have a bearing, you can also print one : https://www.thingiverse.com/thing:2746804 You can see it in my setup I am using REV04a myself in conjunction with my design of an upper filament guide...

Redesigned the original by adding the "Better Bearing" from https://www.thingiverse.com/thing:2746804 Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: No Supports: Yes Resolution: .001 Infill: 25% Filament: PolyMaker PLA Green...

 Help guide the filament.Installed where the runout filament attaches to the machine.Move the filament spool to the top of the machine and need a side guide so the filament has no sharp angles to deal with.Don't use the runout sensor, so I just...

... it from jamming in my printer. ...I've switched to a top-mounted filament holder, but I'm still cautious about the filament getting tangled up inside my printer's mechanisms. ...Print Settings Printer Anycubic Kossel Rafts No Supports No Infill 20%

Filament guide with intentional gap for inserting filament directly, bypassing unnecessary feeding through. The width of the clip is carefully selected, allowing the guide to slide smoothly in place while firmly staying attached. A deliberate angle...

I'm using a simple Bowden adapter and filament guide, which can be found at this link: https://www.thingiverse.com/thing:3638402.

To attach it, you first have to remove the plastic cover with the 'Anycubic Kobra' emblem on it. The mount then simply slides on the metal piece. Usually, the mount should be tight enough to hold on its own, but you can insert a 2x2mm piece in...

... <p>Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=948783 Instructions Using the following options: FrontFaceText = Anycubic TopFaceText = Kobra BottomFaceText = 3D Printer Tolerance = .5 Category: Office

&nbsp;Help guide the filament.Installed where the runout filament attaches to the machine.Move the filament spool to the top of the machine and need a side guide so the filament has no sharp angles to deal with.Don't use the runout sensor, so I just...

I designed this guide to extend the loop of filament, and reduce the strain on the Bowden tube. I have built mine in Purple silk PLA. I hope you find it handy! ... Enjoy!

When not using the Palette, the bracket acts as a nice little strain relief guide for bare filament for normal single color prints and features You will need to clip off the filament sensor bracket and mount the sensor to this bracket. ... Parts...

Replacement feet for the Anycubic Kobra Go or Neo. They increase the base feet height by 8mm. The OEM feet for the Kobra Go were 20 mm so these are 28 mm. Use the screws from the old feet to install these. I added a stainless steel washer beneath...

I designed this filament guide to extend the loop of filament away from the printer, and reduce the strain on your Bowden tube. I printed mine in Purple Silk PLA and it worked out quite well. I do recommend PLA I hope you find this design...