anycubic kobra filament guide 3d models

I could not find anything to fit my Kobra Max - to solve this I had to use my poor Tinkercad skills to remix a common filament guide with a roller. It is for sure a quick and dirty way, I am sure more talented guys can do better in CAD. I have...

I did not have space to fit the Anycubic Kobra Filament holder above the printer so removed the bracket, took off the spool holder and designed this to be screwed into a wall to hold the filament. ... I then printed one of the many filament holders from...

When you have only few or no space next to your printer, this is my solution for you.It features the use of the stock screws of the original Kobra filament holder, the possibility to use JUSH in full width (even two spools on top of the Kobra...

It features the use of the stock screws of the original Kobra filament holder, the possibility to use JUSH in full width (even two spools on top of the Kobra possible e.g. for quick filament change) and filament guide holes to the extruder which...

This is a remix of the Ender 3 Filament Guide. ...The bracket was designed to mount on an anycubic i3 mega.

I designed this basic filament guide for my Anycubic Prusa i3 printer, which functions perfectly on the upper frame. ... Tinkercad: https://www.tinkercad.com/things/i7NwpCNEG7w 03/01/18: I uploaded V2 !

This remix is a revised version of the original Ender 3 Filament Guide, tailored for use with the Anycubic i3 Mega. ...A custom-designed bracket serves as the mounting solution for this specific printer model.

Human: This is a straightforward guide for installing a filament support on the ANYCUBIC i3Mega 3D printer.\r\nPrevents Filament Sensor from becoming detached.\r\nThis design leverages existing screws, eliminating the need for extra...

this is a filament guide i modified to mount the standard anycubic mega s filament sensor to. it lines up perfectly and allows you to feed filament straight into sensor and out other side without having to reach around the back and fiddle with...

This is my first 3D creation, and it's a simple filament guide designed specifically for the Anycubic i3 Mega (S) printer. However, I believe this design could easily adapt to other printers as well. Simply attach this guide to the front right...

guide for filament near the sensor

I designed a custom filament guide specifically for the Anycubic i3 Mega 3D printer. So far, it has performed flawlessly, and I'm confident in its reliability. ...However, if any issues arise, I will promptly update this thread with the necessary...

This is my created Anchor for the Anycubic Kobra side filament system. https://www.thingiverse.com/thing:5633816 I use two M3 screws an nuts. Customized version of https://www.thingiverse.com/thing:5139044 Created with Customizer!

I, being new with FreeCAD, could not get LordCody27's guide model to be editable so I did my best to reproduce a close facsimile of it with some additional length to make room for the filament runout sensor. The original pulley and spacers work...

I made this simple filament guide for my Anycubic Prusa i3 printer, works great on the upper frame. Tinkercad: https://www.tinkercad.com/things/i7NwpCNEG7w 03/01/18: Uploaded V2 ! Print Settings Printer: Anycubic Prusa i3 Rafts: NoSupports: No...

Here is a rewritten version of the filament guide for Anycubic i3 Mega: "Mastering the Art of Filament Guide for Anycubic i3 Mega Introduction Congratulations on taking the first step towards creating intricate prints with your Anycubic i3 Mega! This...

The "Filament spool holder for anycubic i3 Mega by meireles" https://www.thingiverse.com/thing:2932855 I adjusted it upward. I installed two fresh holes to accomplish this. In the lower section, a new Filament Guide has been incorporated. A screw...

UPDATED: New Version also has a spot for the tiny cutters that come with your printer! Remix from: https://www.thingiverse.com/thing:74780 https://www.thingiverse.com/thing:5400693 https://www.thingiverse.com/thing:4702201 Thank you jfrog88,...

This is a remix of the Anycubic Vyper Filament Guide (https://www.thingiverse.com/thing:5345173) by Salamattder. I adjusted the piece so it does not require any additional hardware. Instead, it just slides into the top rail once you remove the endcap...

Hi, So I put a new roll of filament on my Anycubic Mega Zero and it is so tightly wound that the filament would pull back and sometimes the roll would jump/ skip after the extruder pulled hard enough on the filament. I decided to make a quick...

First submission. ... A simple filament guide, made by using the measurements of the original end-caps of the 2020 aluminum.

Lastly, the filament sensor negates the need for a filament guide as it feeds the filament straight down. *I will update the file if I find something wrong with it or something happens that needs fixing and will put any of those updates below...

I made this filament feeder swivel for use with external filament dryers or feed units.. Just print this, assemble with an M10 x 1.5 x 25mm bolt and a M10 x 20mm OD washer on the end. You could also print these too, which I will provide in the files....

I need a filament guide for orizzontal top spool holder. I attached the parts with glue. ... Add clamp v2 and guide v2 with m3x5,7 ruthex brass nut hole.

To keep the sensor from breaking at its mounting position and to ensure a proppier filament flow, I invented this guide that also covers the filament sensor. You need new M3 screws (about 3-5mm longer). The V0.2 file has an optimized filament...

Tips for Working with Filament Here are some additional tips to help you get the most out of your Anycubic i3 Mega and its filament: 1. **Use the correct temperature**: Use the recommended temperature settings for your specific filament type. 2. 3....

Made from durable materials, the Filament Guide is designed to withstand the stresses of continuous filament movement while maintaining its shape and functionality. It comes pre-assembled with the I3 Mega's frame, making it easy for users to set up...

Here is a filament holder that securely fastens to the 7-8mm acrylic width of the Anycubic i3 printer without requiring any screws. ...This design was created using Tinkercad and can be edited online at https://www.tinkercad.com/things/ekRHKkdRO5j.

If your printer is well calibrated, the filament guide should have two articulations - one in the sphere guide and another in the support. I printed the support separately so you can remove it with pliers. To keep things secure, just add a little...

A filament guide to replace the stock spool bracket and smooth the path when using a dryer box. ...Slips on to the same 2 screws the original bracket uses.