anycubic kobra filament guide 3d models

---------------------------------------------------------------------------------------------- A filament guide optimized for the Anycubic Kobra. The guide is screwed on instead of the filament holder. Required are 2 ball bearings of type 608Z,...

This is a filament guide for the Anycubic Kobra (not Kobra Max). I'm pretty sure this won't help or hurt your prints, its more of an organizational thing. When I started using a bearing aided filament spool holder, the filament would come out in...

This is a filament guide for the Anycubic Kobra (not Kobra Max).I'm pretty sure this won't help or hurt your prints, its more of an organizational thing. When I started using a bearing aided filament spool holder, the filament would come out in an...

Just a simple filament guide to avoid tangles. Print with 100% infill for maximum strength but its not necessary. Used zigzag supports for the clip part only. Hole lines up directly over where the filament feeds into the extruder. ... The whole part...

You will need this parts: 2 Bearings: MR106-2RS for each roll This is a bracket to guide the Filament over the top of the Anycubic Kobra (Not Max!) I used a 0.1mm Tolerance to fit in the Bearings. In TinkerCAD there is another Version of it. <a...

You will need this parts: 2 Bearings: MR106-2RS for each roll This is a bracket to guide the Filament over the top of the Anycubic Kobra (Not Max!) I used a 0.1mm Tolerance to fit in the Bearings. In TinkerCAD there is another Version of it. The...

Remixed version of JDBull's minimal filament guide. I wanted it closer to the spool (and center of the rail) so I mirrored it to other side. I also didn't quite like the slit in the original so I created a solid version as well as created a slit...

Filament guide for the Kobra that snaps onto the top rail by sliding it on from underneath. It was designed to fit the main center section of the top rail but I've also included a freecad project file where it's fully parameterized so you can adjust...

Filament guide for the Kobra that snaps onto the top rail by sliding it on from underneath. It was designed to fit the main center section of the top rail but I've also included a freecad project file where it's fully parameterized so you can adjust...

Simple guide to help keep the filament in the center of the print area over the print head on an Anycubic Kobra Neo printer.

This guide created for Anycubic Kobra Go and use with bearing U623ZZ

This is a remix of the Filament Guide from @tommytwothousand. ... It has been adapted to the Anycubic Kobra Neo, replacing the original spool holder and using the screw threads. ...

Filament roller guide for Anycubic Kobra Go. you can see where the filament was being scraped from the extreme angle. You will need a standard bearing and a screw. The tolerance is tight so my screws threaded in. Will get a nut when needed. All...

This is a Three-part filament guide for Anycubic Kobra, ideal if you have a filament holder on the side of the printer, or as in my case a dryer. It guides the filament from the side, and can be mounted in the two holes on the printer sides of the...

So, I made this filament guide to eliminate drag and line it up with the sensor. Feel free to improve on this, just mention me in any modded version please. ... Note: This is not for the stock Kobra max spool holder that is mounted on the bottom of the...

I saw some other filament guides on here and wanted to make something similar. This is what I came up with. It's actually my first attempt at a print-in-place moving part and it worked, so that's pretty sweet. It clips onto the spool holder. The...

A very dirty remix for mounting the filament guide with runout sensor. I use underprice sensor in less than 1 dollar fron Ali https://www.aliexpress.com/item/1005003397498506.html instead $15 for original sensors. ... Find the way to secure sensor...

Filament guide for the Anycubic Kobra

This guide helps filament across and directs down towards the extruder filament guide. The small guidewheel is shamelessly borrowed from LordCody27 (https://www.thingiverse.com/thing:5672602). (spool and 2 axle guides required from 5672602). See...

This is a filament guide for Anycubic Kobra MAX. See photos how it is attached. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/jfZj4hKOWfT

Remix of https://www.thingiverse.com/thing:5386260/remixes for the Anycubic Kobra Printer.

Hi all, For all of you using an ANYBOX V2 (https://3d-druck-vorlagen.de/anleitung-filament-box-selber-bauen-die-anybox-v2/) or another PTFE guided filament feeding. I was a worried that the PTFE tube makes a huge impact after every retract. This...

... ... Just made the upper filament holder (another cool stuff) and put it on the top of the printer. Then the filament hangs down and nearly kinked before it moves in printer. So i made this thing to guide the filament smoothly to the printer-input.

<p>Onshape model: https://cad.onshape.com/documents/65ede40b24f5475b03a657b5/w/b61737489ce3883fe20f99e9/e/08067fb49c04efd261b3984d</p>

First I printed and tried the filament guide from niterider144, because I really liked the guide with the ball bearing. But unfortunately I didn't manage to attach this guide properly with the zip ties. It always wobbled somehow. I therefore only...

Fusion between Artillery filament guide and Anycubic Kobra. ... Original design: https://www.thingiverse.com/thing:5030165

Kobra Max Filament Guide. ...Clips on the top construction.

Everyone knows it, with leftovers or film end without spindle it can happen that it jumps over the holder. ...This protection prevents this, because it is high enough that the filament does not jump.

I've used WeTheDylan's filament guide since I purchased two Kobras a few months ago. The guides broke on both machines after a few months. So all I did was beef up the walls on the guide to make it stronger. ...