anycubic i3 mega z axis adjustment 3d models

A mark denotes a 0.1mm increase on the Z-axis when turning the nut clockwise or counterclockwise, as M3 metric nuts have a pitch of approximately 0.5mm. Divide by 5 for precise adjustments. Recommended print layer height is 0.25mm with cooling...

In case you need to lift or move the bed of your Anycubic i3 Mega, refrain from using its height-adjusting knobs - this could result in your bed losing its adjusted position along the Z-axis. I've personally experienced this issue once before. It...

Remix of https://www.thingiverse.com/thing:1445744 to fit AnyCubic i3 Mega printer and Neoteck NTK021 gauge. Adjusted spacing for 8mm rails spaced 50mm on center. Moved the hole for the gauge mount higher as my gauge bottom's out with the original...

Save your fingers by using the manual adjustment knob for the z-axis. Before making adjustments, ensure that your steppers are disabled to avoid any accidental movements. The g-codes I've added set the print parameters as follows: layer height at...

... ...To create a quicker adjusting mechanism, I remixed the design to include a spinning wheel knob that effortlessly raises or lowers the z-axis with a simple turn. The knob smoothly clicks into place on the wheel, thanks to its precision engineering.

This is a Cable Shroud for the Anycubic I3 Mega X. It was inspired by this [shroud](https://www.thingiverse.com/thing:2886955) , that doesn't give the protection i was looking for on my Mega X. I made a longer shroud to prevent the upper beam from...

Dead simple tool that hangs from the X-axis rods and can give accurate positioning relative to the y-axis rods. ...Probably the most accurate method of aligning the X-axis carriage of these printers.

# Microscope Z-axis height adjustment mount. [These are the ball bearing wheels I used](https://www.amazon.com/gp/product/B07TH7WS2N/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1) They are not common or cheap. I just had them on hand. You will...

Modified Filament Sensor Bracket For Anycubic I3 Mega 3D Printer The modified filament sensor bracket is designed to work seamlessly with the original magnet from the Anycubic I3 Mega. This innovative upgrade enhances the overall performance of your...

Parts to print: X-axis: + 1x CC_X_PrinterHead_M3 or CC_X_PrinterHead_CT (mounting material M3 screws or 3mm wide cable tie) + 1x CC_XZ_RightTop + 26x Chain-Link-A (credits to [dmaMods](https://www.thingiverse.com/thing:4253211)) Z-axis: Left-side: -...

Using the same hardware that comes with the printer, a simple thumbscrew makes it easier to adjust the Z axis zero position. ...One of my main objectives when creating these parts is to utilize as much of the original equipment as possible, rather than...

A straightforward device suspended from the X-axis rods, this tool enables precise positioning in relation to the Y-axis rods with remarkable accuracy. ...It stands out as one of the most reliable methods for aligning the X-axis carriage on these...

This sturdy LED holder is designed specifically for the Anycubic I3 Mega, boasting a unique no-screw mounting system that relies solely on pressure to secure it in place. One of its standout features is its modular design, allowing users to attach...

PCB Printed on 3D with Anycubic I3 Mega Printer, Nozzle 0.6 and PLA Black Filament. Attempting to print with wood PLA failed as it clogged the holes. To avoid this issue, you may need to manually drill some holes depending on the type of filament...

Humans adapt components specifically for z-axes measuring 8 millimeters in diameter. ...To secure the knob to the z-axis, employ two screws approximately 3.8 millimeters in thickness.

Endpoint Limit Switch for Z Axis Compatible with Anet A8 You'll also need: - M4x15 with Nut - M5x50 with Nut - Spring: D8 x 25mm Enjoy Your Build!

I remixed the Anycubic i3 Mega C170 C270 Cam Mount by Bishbish2000 to fit the Logitech C270 webcam perfectly. ...Since I didn't have any M6 screws or nuts, I adjusted the bottom hole to accommodate a M3 threaded insert with an outside diameter of 4mm,...

Extruder Knob for Anycubic I3 Mega is convenient due to fine adjustment working while manually extruding filaments, however it's not suitable as a means of removing it instantly when changing filaments. ...Therefore, I attempted to create a handle that...

Simple Anycubic I3 Mega BLTouch V3 Mount. To adjust the height, use washers. Position it as far from the hotend radiator as possible. Four M3 screws are required for installation. ... BLTouch: https://amzn.to/2EHRcdj (This is an affiliate link.) ...

I just updated the cooling mod on my Anycubic I3 Mega. The hotend cover has been tweaked for optimal performance, and the cooling module is now significantly improved with two available options. ...Additionally, I've adjusted the nozzle angle for better...

A magnetic Webcam Holder for a Anycubic i3 Mega and a Logitech C270 Webcam. It moves with the Z axis which results in a perfect view onto the current layer.Print instructionsParts7x 10x5mm Neodymium Magnet7x M3x14 Flat Head Screw1x M3x 12 Flat Head...

Anycubic I3 Mega 3. Leadership and everything will get better :-)\ Since my I3 has always been somewhat unstable in the X-axis, I simply gave it a 3rd rail. This is no precision rail but a third rail to stiffen the axis against deflection and reduce...

It's designed for the Anycubic i3 Mega with the Side Extruder Support mount v2 that I used from User Alpharic - Thank You! https://www.thingiverse.com/thing:2448418 I bought this chain from Amazon: NATE 10x10 Chain ...

Here is the rewritten text: Support for AnyCubic I3 Mega Printers. Printed with a layer thickness of 0.2mm and 40% infill density. !! ...Flat Printed !!

Halter für die OV5647 Raspberry Kamera, passend für den Anycubic i3 Mega Halter / Arm ist für dieses Gehäuse: https://www.thingiverse.com/thing:3728526

This is a remix of original by ScottyDoesKnow , is the lock for the bed of anycubic i3 mega first Version, which has a smaller screw to level bed

The user is experiencing a malfunctioning heating bed handle on their Anycubic I3 Mega 3D printer. ...The issue is causing problems during printing operations.

I've modified the holding device to fit the AnyCubic i3 Mega (s). ...The modification has allowed it to accommodate the printer's specifications.

A movable tool holder, to assort tools coming along with the I3 Mega from Anycubic. ... Spacers on backside prevent to block airflow holes of the housing.

Spool Holder for Anycubic I3 Mega / S Print parameters: 0.25 mm layer height 25% infill concentric Can use one or two sliding locks as needed. ...