anycubic i3 mega x 3d models

Each magnet measures roughly 5 mm wide x 3 mm tall. They are fairly common and easy to purchase from various online retailers. I used “Scotch Heavy Duty Clear Mounting Tape” to adhere the fixed head to the wall surface.NOTE: this door catch is not...

So the steps are: #1 glue magnet into MagnetMount, #2 press the mount on the screw - do not glue yet, #3 test direction and adjust mount, #4 once it matches, mark direction with a pencil and glue MagnetMount to the screw.The wind mount has a M6...

Overlays are 2 layers X 0.12mm = 0.24mm height in total. Then the overall height of the card (with overlays) would be 1.32mm when printing is completely finished. ...

If you need more speed buy a 100 RPM motor, but you probably want to spin it a lot slower, which is possible by turning the speed knob down.I bought my parts from amazon, but if you have the time, you can get them very cheap from...

...  The top of the lid is placed down on the print bed.  There are some overhangs that end up sloppy without supports but it is functional.Updates:Added model for Jar 60mm wide x 50mm tall.Added 22mm wide Jar series.Added De-taper Lid.

Transparent versions of the presets are also included.The main tweakable parameters are in the Parameters section.If adjusting the corner radii you may need to offset the screw positions using the Screw X (Sox) and Screw Y (Soy) parameters in the...

When the hotend is down to 40 degC then the Z axis will raise to 250mm and X axis stick/carrier will push the micro switch at the very top right corner of the printer where it's mounted on 4020 profile. See picture. ADD ANOTHER PRINTER: In addition,...

IF YOU ARE HAPPY WITH THAT, A LITTLE DONATION WILL BE VERY NICE <3 https://www.paypal.com/donate/?hosted_button_id=5F525DYM8GXK4 If you want to do a remix or changes to the design, you can get the Fusion 360 and STEP file here:...

Die Druckteile werden in folgender Ausführung benötigt: °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 1x Main Body_6_inch_motor_angle_0.stl 4x Swing_for_Bearing_Wheel.stl 4x Feet_Inset_Top.stl 4x Feet_Inset_Bottom.stl 2x...

And if anyone has questions about the build, feel free to contact me as well! Materials The following materials are required for this project: A 3D printer with a build volume of at least 160 x 160 x 160 mm (6.3 x 6.3 x 6.3 in) The STL files...

etc.&nbsp;You can either print the individual 2 piece middle plate and bottom plate in clear, or print the one piece plate to about 4mm (at 0.2 layers that's at about layer 32) and switch to your filament from clear to a color like i did.Print as...

You may have to use an x-acto knife to widen the bottom of the knob so it fits snugly on the rotary knob on the MP3 Player. It is best not to push the Candle Holder snug to the lid because you need to push down on the knob to switch from track and...

The maximum required print area is 180 mm x 180 mm (I used my Prusa mini as upper limit) The clock is designed around common parts readily available online like a 5V Stepper motor, a Arduino nano and a common RTC and bearings. A more specialised...

If another dimension is needed, bigger or smaller, the model can be scaled on one axis.&nbsp;I use it for a MacBook Pro 16'' 2019 that is 16.2mm and added two 1mm adhesive foam sheets, one for each side, that added to approximately 18.2mm so it has...

The original file is from the collection of asteroid radar detection of the PDS site. The file's names explained: name_1_x_10_y.stl is 1 : x * 10y. So _1_6_10_7 is 1:600000000 or one in 60 million.<br> <h4>4660 Nereus</h4> This skyscraper sized...

I also have a professional CAD protractor and a model of the smallest protractor for drawing.Weight: ~ 15g.Size: ~ 11x6 cm.Print time: ~2h.100% printable (no additional parts needed).Preparing.Before printing, make sure that your printer is in good...

Some igniters are meant for different kinds of motors and you might get a surprise if you use the wrong thing.&nbsp;Surprises are bad, plan everything.Pick your launch site carefully, you usually need a half mile radius or so when launching unless...

I put the cylinder above the top right corner and set Layer Start X and Layer Start Y to a high number like 500. I've included the 2 mm tall swap tower that I use. SWAPPING FILAMENTS: When changing filament, I never yank the old filament out as...

&nbsp;A TELRAD interface shouldn't be too hard to make, either.&nbsp;Can you add x part?Within reason, I want to make this as functional as possible. &nbsp;But my time is scarce as a grad student and job seeker so things are slow.</p><p><strong>Does...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

For details on the original design, check out the CubLED LED Cube 8x8 Matrix.This version incorporates several modifications:A different LiPO battery.Slightly different LED matrix panels.A reed switch for turning it off and on, using an embedded...

To handle this, you need to unscrew the wheels on the print head and mount the LeftBeltClip and RightBeltClip under those screws.The X axis timing belt slides into the slots on those two parts. Note that you'll want to install the timing belt on the...

Create your own version with these options: qr\_y=0, qr\_x=0, tag\_height=80, tag\_width=80, perimeter=-1000, corner\_radius=10, case\_thickness=1.8, hole\_r=10, hole\_y=0, hole\_x=30, per\_h=10, per\_w=3, obj=1, add\_sub=1, qr\_size=33,...

Then, you can enter the data displayed in the name tag creator (width x depth x height) into the coaster generator. If you're using rounded corners, enter in the coaster generator the data used for the frame corners in the name tag generator, not...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Avoid lifting and warped prints!There is a small amount of support needed - "for support enforcers only."Under the elevator shaft on the Middle Floor and Top Floor.The elevator door on the base floor.Increase the size of your “Dice Tower - Building...

Then, you can enter the data displayed in the name tag creator (width x depth x height) into the coaster generator. If you're using rounded corners, enter in the coaster generator the data used for the frame corners in the name tag generator, not...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Once the correct amount is placed (making sure you can still mount the motor), you can fix it by gently dropping some epoxy over it.You'll also need 8 pcs of neodymium magnets for the cabin/lid.8 mm diameter 3 mm thick, like these...