anycubic i3 mega ultrabase replacement 3d models

A custom-made replacement filament sensor magnet housing designed specifically for the Anycubic i3 Mega Ultrabase printer, ensuring that the filament travels straight up to the extruder without bending or kinking. This streamlined design reduces...

The i3 Mega's top surface is designed to accommodate a 120mm fan, ensuring that both the printer and the Ultrabase stay cooler for longer. ...This innovative feature allows for rapid heat dissipation, enabling faster cooling of the printed object.

I originally tried using Alex100dre's cable guide for the original Anycubic i3 Mega but it didn't fit on my later model with Ultrabase. I completely remade this from scratch to work with the newer Anycubic i3 Mega and its base. My version is...

The Ultrabase version's lack of a bed level sensor might mean the connector size or position differs from the initial i3 Mega model, making this remix a better fit if that's the case. ...I also included a slot for a cable tie, though ultimately decided...

I found that the version by hampisch (https://www.thingiverse.com/thing:2266134) didn't quite fit around the cable connector on my MEGA so I modified it to allow more space.Since the Ultrabase version doesn't include the bed level sensor, it may be...

I found that the version by hampisch (https://www.thingiverse.com/thing:2266134) didn't quite fit around the cable connector on my MEGA so I modified it to allow more space.Since the Ultrabase version doesn't include the bed level sensor, it may be...

... well, with older models. Please note that this item will limit the maximum build height of your i3 Mega from 205mm to about 200mm. ...A new and improved version that migitates this flaw can be found here (https://www.thingiverse.com/thing:3703089)

... also fit older models, although not very well. Please note that this item restricts the maximum build height of your i3 Mega to approximately 200mm from its original 205mm. ...A new and improved version that mitigates this flaw can be found here.

I built a straightforward clip to hold a 12V LED light that shines on my Anycubic i3 Mega Ulrabase 3D printer's working area. The light moves up and down with the Z axis, illuminating the printing space from the right side. Its incidence angle is...

In my tests, I could raise the head as high as 207mm from the build plate and the cable guide was still far from being a problem!You need to make sure, though, that the printer's frame edges do not damage your cables near the plug when moving on...

Since 2018, hundreds of i3 Mega owners downloaded and used my cable guide version 1 which worked great but came with one major flaw: The maximum build height was reduced to about 197mm.\r\n\r\nNow, I finally redesigned the guide, keeping all its...

Since 2017, hundreds of i3 Mega owners downloaded and used my cable guide version 1 (https://www.thingiverse.com/thing:2634402) which worked well and looked good - but came with one flaw: The maximum build height was reduced to about 198mm. Now,...

I'm getting my Anycubic i3 Mega ready for an IKEA housing, but first, I need a front feed since there's limited space and no room for the standard side feed of filament.\r\n\r\nI've opted for this extruder mod from Sensibelchen_AB on Thingiverse:...

Custom Stepper Driver Cooling Duct for Anycube i3 Mega UltraBase. Visible on the picture, TMC2208 drivers are installed with their wires reversed at the motherboard connectors. ... Crafted an even better version:...

A custom bracket is designed to secure the heating bed of the Anycubic i3 Mega Ultrabase printer, specifically addressing a potential issue where the glass plate detaches from the heating plate. ... This specialized bracket is suitable for use with ABS...

Finally getting my Anycubic i3 Mega (version 3), I was surprised by how much less adhesion I got with the stock Ultrabase compared to the round one I once bought from Amazon. The surface of the round version looked and felt more coarse. I then...

For additional information, please refer to the detailed description below: Summary: A specially designed Stepper driver cooling duct specifically engineered for use with the Anycube i3 Mega UltraBase. ... As shown in the accompanying picture, TMC2208...

Protect your Anycubic I3 Mega 3D printer's bed with a durable front shield, ensuring optimal performance. ...This shield is designed to safeguard both the left and right sides of the bed, preventing heat loss that can impact print quality and speed up...

Hi, I've got an i3 Mega UltraBase with TMC2208 drivers, and I designed a duct for it over on Thingiverse - https://www.thingiverse.com/thing:2773533. It worked okay until I upgraded to Marlin 1.1.8. With the new firmware, I was able to hit higher...

Here's a modified duct design for the Anycubic i3 Mega using standard 5015 blower fans. The clips will be snugly fitted, so gently wiggle the duct while pushing on its bearings. As requested, I've added a mirrored version of the cooling duct, along...

Summary Here's a remixed duct for Anycubic i3 Mega that utilizes standard 5015 blower fans. The clips of the duct will be tight, so wiggle it while pushing on the bearings. As requested, I've added a mirrored version of the cooling duct. It's worth...

After numerous attempts and failed prints, I remixed https://www.thingiverse.com/thing:2765158 to create a simple yet effective holder for my i3 Mega's 5015 fan. The more infill used, the better. Note: I've upgraded to Marlin 1.1.8, allowing me to...

... by roundisfunny on Thingiverse. ...Take the original funnel from him and utilize this component instead of the ending-piece. If it won't fit into your Anycubic, shorten the bar spacer as illustrated in the 4th picture or edit the part before printing.

This fit exactly on my i3 Mega with an Ultrabase and 8bit Trigorilla. You need to print two of each. ... You can use only the feet without the holder and stick some felt pads under them or use double-sided tape to stick the holders into place and stick...

... of you might find it usefull as well. Update: Added a little clip to better fix that cableguide to the extruder. Print Settings Printer: Anicubic i3 Mega Ultrabase Rafts: No Supports: Yes Resolution: 0,2 Infill: 20% Category: 3D Printer Accessories

... too. Print Settings Printer: Anycubic i3 Mega Rafts: Doesn't Matter Supports: Yes Resolution: 0,2 Infill: 20% Notes: This probably will also print without supports, but I didn't have time yet to test that. ... Category: 3D Printer Accessories

ANYCUBIC i3 Mega UltraBase 5015 Blower Turbo Fan Cooling Original Hotend E3D Multi is a high-performance cooling system designed to optimize printing results. ...This innovative solution elevates the ANYCUBIC i3 Mega's capabilities by effectively...

I recently had to replace the power supply on my I3 Mega because it stopped working, so I searched for a replacement adapter and found one at https://www.thingiverse.com/thing:2895665 that fits this model https://www.amazon.de/dp/B00P2CTSBI .

This is a remix of llapao's "Anycubic I3 Mega 5015 duct fan cooler ultrabase".\r\nI picked the crescent-shaped duct version because it's the most compact design that doesn't block your view or access to the nozzle.\r\nSo, I flattened the crescent...

One day after levelling the bed of my Anycubic Mega Pro, I immediately started a print job but did not remove the probe. The foam melted, so I found one on Amazon, bought it but then realized it did not fit. I tried cutting the foam but it was not...