anycubic i3 mega s firmware upgrade 3d models

Direktextruder Anycubic i3 Mega S you also need a set of screws: - 4x m3x28 - 2x m3x20 - 2x m3x25 - 6x m3x9 this kit only works with the fan holder designed by me it can be downloaded under my profile;)

This is a filament spool holder prototype for the Anycubic I3 Mega / s. ... -better printing result -relief for the engine Not perfect but it works bearing you need: 22x9,5x6 (turn Teil1 90* Teil2 180* Teil3 180*)

This is a filament spool holder prototype for the Anycubic I3 Mega / s. ... -better printing result -relief for the engine Not perfect but it works bearing you need: 22x9,5x6

80 mm led ring mod for the Anycubic i3 Mega S mit a Fan duct mod Inspired by: https://www.thingiverse.com/thing:2919948 and https://www.thingiverse.com/thing:2503909

... to fit the Quimat QY08-2 mosfets that can be found on Amazon (they are also sold under other names). https://www.amazon.co.uk/dp/B077HP7XX9 The holder is mounted to the SD card holder in the Anycubic i3 Mega-S Can be printed without any supports

... will be eliminated. It is compatible with all kinds of filament spools. Good prints ... Click the link below to see the new spool holder design for the Anycubic i3 Mega S. ...https://cults3d.com/en/3d-model/tool/anycubic-i3-mega-s-spool-holder-v2

A tiny seal for the i3 Mega S

Kabelhalter für den Anycubic i3 mega und mega s. wird einfach in den Schlitten vom Bett eingeklipst. der Deckel wird in die Grundplatte eingeclipst. Drucken unbedingt mit brim und supports. durch die kleinen filegranen Teile wird es sonst nichts...

It's a nice bracket for the PiTFT to put it in place of the original display from the Anycubic i3 Mega S. I designed it as part of my upgrade from Marlin to Klipper. I don't know whether the bracket goes well with a normal Raspberry Pi. It works fine...

After upgrading my Anycubic i3 Mega S (with new stepper drivers [2208] that had very large heat sinks), I didn't want to file the heat sinks down and i didn't want to buy another fan. ...I had just replaced the 50x10 with a new very quiet and high cfm...

For those of you who removed the annoyingly unreliable filament-out sensor on your Anycubic i3 Mega or Mega S. Use this filament guide in place of the sensor assembly. ...You will need to cut a piece of plastic tubing (I used the PET tubing from a pen...

Trash bin for Anycubic i3 Mega S. (I don't know if it fits to Mega also, you can check the screw holes if it fits) No supports needed. ... I've printed the Base with %20 infill and the Box with %100 infill and 0.2 mm layers.

Hier ist ein selbst erstellter Halter für den Anycubic i3 Mega & Mega S. Da der Mosfet vom Heizbett ein Platz gesucht habe und ich mein Netzteil auserhalb vom Drucker habe, hab ich den Platz genutzt. Da wo das Originale Netzteil war ist nun der...

Hier ist ein selbst erstellter Halter für den Anycubic i3 Mega & Mega S. Da der Mosfet vom Heizbett ein Platz gesucht habe und ich mein Netzteil auserhalb vom Drucker habe, hab ich den Platz genutzt. Da wo das Originale Netzteil war ist nun der...

This is a minimal version of the improved hotend for the anycubic i3 mega (https://www.thingiverse.com/thing:2919245). I made this for my i3 mega S because my radial fan was a little to big for a nice fit with the orginal desgin. Further I wanted...

------------------------------------------------------------------- Adaptador para la secadora Sunlu filadryer para Anycubic I3 Mega-S. Se engancha en el marco de la impresora. Se necesitan dos conectores (10 o 6 mm) y tubo de teflón . Las partes...

I wanted to install a 60mm LED ringlight on my Anycubic I3 Mega-S printer, so I built an adapter to match the existing screw holes. The Ledring attaches securely with adhesive, and you must connect wires to the second fan's electrical terminals. ...I...

Plug & Play Tool holder for the Anycubic Mega and Mega S. ...Simply plug in and play, easily attaching to the frame via Plug & Play.

[999D](https://www.thingiverse.com/999d/) provided a nice replacement for the extruder lever of an Anycubic i3 Mega S: https://www.thingiverse.com/thing:4248053 This is a remix by cutting the model in half and glued it together afterwards. ...For easier...

Direct cable access requires modification to the Anycubic i3 Mega's casing. Specifically, the red, green, and black sockets located on the right-hand side need replacement with open-ended cable passages. ...This alteration allows for unimpeded cable...

... fan duct from H_Run. ... I created a wrap-around ring with 270° exhaust ducts. I also removed a small cutout, which is why the original did not fit my printer. This remix is for the Anycubic i3 Mega S (2020). ... Printable without any support.

*While removing the filament in the Anycubic i3 mega s 3D printer, the tip of the filament gets stuck and it is difficult to come out. Thanks to this apparatus, you can easily remove the end of the filament by cutting it. WARNING: This apparatus is...

Simple mounting plates are designed for the Anycubic i3 Mega S. These plates enable users to easily attach components to the spool holder and Z-axis. A total of two, four or six 6x2 magnets are required, which can be sourced from...

... remix of https://www.thingiverse.com/thing:4193861 The original source is designed for 5015 fan and used for https://www.thingiverse.com/thing:3954252. ... In order to reuse Anycubic I3 MEGA-S original fan for direct extruder, mount was re-designed.

The Anycubic i3 Mega S requires an upgraded cooling solution, which involves replacing its bizarre stock driver board cooler with a more efficient one. This may necessitate re-seating the heatsinks, ensuring that their fins are perfectly parallel to...

The arm or lever on the extruder of my Anycubic i3 Mega S snapped and I was unable to manually load or unload filament by hand. It appears that the original is pretty fragile and will likely need to be replaced sooner rather than later. This upgrade...

Firmware Marlin 2.0.9.2 for Anycubic I3 Mega stock and installed TMC2225+DRV8825+BMG. MBL works properly. Sorces are for TMC2225+DRV8825+BMG. ... Installation via Cura Printer setup-update firmware-my file: AI3M2092-TMC2225-DRV8825-BMG-MBL.hex

Modified the frame to fit perfectly around the Anycubic i3 Mega S, ensuring a precise margin and screen size. Mirrored the cover's design so that it can be mounted inside out, creating a seamless look even when the lid is closed - check out the...

The Anycubic Mega S i3 Glue Holder is a sturdy accessory designed to keep your workspace organized and clutter-free. Its compact design fits neatly on the side of the printer, providing easy access to glue sticks and other small items. With its...

I've built an adapter to make this case fit the Anycubic I3 Mega S. You'll need to remove the touchscreen for this to work. Note: This is currently a work in progress, and it's possible that it won't fit perfectly yet. ... Don't print it right now; I...