anycubic i3 mega s dual extruder upgrade 3d models

Anycubic I3 Mega Dual Spool Holder based on the design of the Prusa Spool Holder. Split into two parts for no support printing. Assembly is simple. Screw in part two into part one and you're good to go. Just clip onto the top of the I3 Mega and place...

Note: If you have trouble downloading this model, you can also find it here: https://www.prusaprinters.org/social/55222-tyler/prints I converted my Anycubic i3 Mega-S to dual extrusion, and I was originally working on a guide showing exactly how I...

I converted my Anycubic i3 Mega-S to dual extrusion, and I was originally working on a guide showing exactly how I did it (since the way I did it is different from what I've seen posted already) but.... an entire guide is a lot of work and I'm not...

I SUPPORT THE DUAL FAN FOR ANYCUBIC I3 MEGA DRIVERS. I USE TWO 50MM ULTRASILENT FANS. A "Y" CABLE IS REQUIRED TO CONNECT THEM. CAUTION! When closing the printer, I noticed that the support exceeded 2 mm in height. ...To address this issue, I created a...

This is a vibration damper for a Titan Extruder on the Anycubic i3 Mega. I changed the orientation of the extruder, so it is easier to feed filament. The extruder gets mounted with M4 screws and nuts to the struts of this damper. ... Print this...

I created this mount plate to hold a dual MosFET print circuit board into the AnyCubic I3 Mega printer. The original idea can be found on Thingiverse elsewhere. In this version, the MOSFET PCBs were still attached and are smaller than the original.

Human: This is a remake from the Anycubic I3 Mega MKS Mosfet Holder design by Petrzak. I'd like to use two MKS Mosfets, one for the bed and another for the hotend. In this case, I'll need a dual support for the two MKS mosfets. Here are two...

ANYCUBIC i3 MEGA S BMG CARRIAGE Hello This is Direct Extruder CARRIAGE designed for BMG Dual Extruder and standard E3D V6 hotend set for Anycubic i3 Mega/Mega S. My target was to get lightweight BMG direct extruder carriage. Many of those parts are...

... might need 4 screws, that are just a bit longer than the original, to install the box. And you will need 4 M3 nuts. The fan duct you see in the picture is this (Anycubic i3 Mega S - Fan Duct by matism09): https://www.thingiverse.com/thing:3564168

Hi all, My first "thing" is finally here! ...I wanted to create a tool holder that includes space for my calipers, scissors, cutter, pencils, and some notes too. There's also room for the bases of my very first printed owl pair.

With just a few tweaks, you can transform your existing 3D printer into one capable of using this extruder setup, incorporating only the necessary components from the provided list to get started. The extruder itself features a tube that guides the...

I removed the curved bit, nothing else, because having to print all the support for more removal was taking as long as not removing anything in the first place ;) In case you need a caliper, I have chosen a Turata: Amazon DE: https://amzn.to/2QCMiD7...

Full cover for plug and cables for the Anycubic i3 Mega extruder. -The front door and the top circle give easy access to the plug and filament entry. -Easy to print (no supports) -Front door ready for 5x1mm magnets. ... I hope you find it useful!

The Anycubic i3 Mega extruder gets a comprehensive cover and cable system. This setup makes accessing the plug and filament entry a breeze through the front door and top circle. Printing this design is effortless, requiring no supports at all. ...The...

... too high for the structure, so it cracked at the first angle from the top. That's why I added the reinforcement ridges. Print Settings Printer: Anycubic i3 mega Rafts: NoSupports: No Resolution: 0,2 mmInfill: 60% Category: 3D Printer Accessories

This direct drive extruder uses Anycubic i3 mega original parts.(NOT S model) Extruder motor cable and part cooling fan cable needs to be extended. Parts are not show’n here as a correct print orient. If you need quidance to fixing up your print...

About This device is engineered to replace the original metal extruder and printed filament sensor (optional) of Anycubic i3 Mega 3D printer. Updates + 19.02.18 - First release Main features 1. No additional screws, bearings, spacers, etc are...

A mount to rotate the Anycubic i3 Mega extruder horizontally. ... _Advantages:_ - Easier filament insertion makes printing more efficient - A shorter PTFE tube provides more precise filament feeding and retracting, leading to better print quality...

Hi, This is my Direct Drive Extruder for the Anycubic I3 Mega. This Extruder was printed in ABS. It works perfectly with TPU, PLA, ABS, PETG Filament. Parts that can be used from Stock: Nema 17, Extruder Rad, Feder, Druckrolle, Heathead,...

... to Work with 608 Bearings. I'll Keep You Posted Initial Post ------------- Separated the Base into Two Parts to Fit the Print Bed Size of AnyCubic i3 Mega. For Print Settings, etc. ...Visit the Main Thing: https://www.thingiverse.com/thing:3035871

This is a vibration damper for a Titan Extruder on the Anycubic i3 Mega.I changed the orientation of the extruder, so it is easier to feed filament.The extruder gets mounted with M4 screws and nuts to the struts of this damper.Print this on the flat...

A printer extension for the Anycubic I3 Mega that enables printing with flexible filament. ...Make sure to check after installation that the roller facing the gear can still move freely.

Designed a mount for the Bondtech BMG (and its clones) extruder for my Anycubic i3 Mega so it can work with the X axis cable chains with adequate clearance. For v1: Use pancake stepper motor to ensure clearance if you are using a rear mounted 5015...

Here is another version of an Extruder Holder for the Anycubic I3 Mega. This one is placed on top of the printer to feed filament from the right side. Now, I have also designed a new version (https://www.thingiverse.com/thing:3223705) that goes down...

Designed a mount for the Bondtech BMG (and its clones) extruder for my Anycubic i3 Mega so it can work with the X axis cable chains with adequate clearance.For v1: Use pancake stepper motor to ensure clearance if you are using a rear mounted 5015...

...I already ordered a second Anycubic i3 Mega to use for the conversions. Update 5.02.2019 Now you can start printing all parts...I have finished the design! ... Update 27.02.2019 A plug for the cables Update 4.03.2019 Now it's ready for a test print

90° Winkel, Halter für Extruder für eine bessere, gerade Filamentführung.

This is my custom Printhead cover design for the I3 Mega, featuring a 40mm Noctua NF-A4x10 fan for efficient heat dissipation in the heat box and an EBM Papst 9591904100 fan for cooling the printed filament.\r\n\r\nTo accommodate the Papst fan, it's...

I took inspiration from the Dual-Sided Cooling Duct, but had a few issues with it, namely: * The bracket didn't fit my Mega-S properly * The ducts were fatter than they needed to be (imho) * The ducts weren't aligned quite to my liking The main issue...

Modified from (http://www.thingiverse.com/thing:3333652 by Piotruchawro) Printed in ABS, Temps 240/80, In Fill 25%, Layer Height 0.2mm, Shell Thickness 0.8mm, Modified the Design to cater for Zip Ties to retain the various wires, the Lower Tangs on...