anycubic i3 mega s dual extruder upgrade 3d models

But if you want to see a good video about MTC Chassis then this [Yuran Liu's MTC Chassis Video](https://youtu.be/z6Y_cUs4_Z8) is the one you are looking for :) See also this [video of MTC+TPB highlift](https://youtu.be/tlIHbWKtQcE) ####NEW: Take a...

(Hopefully you're not far enough off to need to tune your slicer's horizontal expansion settings and re-print)Once the top shaft is working, slide the grip piece onto it then set aside for the moment. Press the bottom shaft gently down into the...

Since it's not going to really be seen up close, I wasn't too worried about the details and just wanted to give it some variation. Step 3 - Gluing and Assembling Joints Each of the fingers consists of 4 bones with little hinge joints between them. At...

It seems like most people just use Solid Clamp mounts for this sort of thing and i guess if you need absolute stability for realism that's fine if you can't go for a full sim pit, but I found that solid desk clamps just didn't work that well for me...

However I have at least a year's worth of projects in front of me, so I thought I would release my first version and hopefully get some feedback before starting the next version. I'd appreciate any advice on a Bluetooth/amp module and speaker...

If you're looking to do the control box removal on a CR10 (non S), it is currently untested. Proceed only if you're willing to mess with things. I will be testing on a CR10 soon. The linear rail mod works fine on CR10 machines. The control box...

For me that's ok. For longer versions I'd probably go to four or more. Try it out and let other users know in the comments.</p><h3>&nbsp;</h3><h3>WHAT YOU NEED FOR ONE MOUNT</h3><ul><li>1 KLAMBY: IKEA sells them in a double pack für 5 Euros</li><li>2...

It is almost like a signature but not quite one.&nbsp;This was a collaboration project with the world's Leaden engineer. Me and&nbsp;<i>Not Applicable Products</i>.</p><p>It is a work of art. Everyone should have a...

Also, a new vertical slot was created on one of the base's walls, to provide support to the side plates throughout its whole height.The former change should provide a stronger friction fit between the pieces, and the latter change should...

You can make your own with this expansion set http://www.thingiverse.com/thing:1321230 Objectives Students will understand what genetic modification is. Students will model how restriction enzymes work. Students will model gene splicing. Students...

The low-profile version should be used if there's no need to clear a back-splash or something similar.&nbsp;Hardware for Assembly and Installation:60x10x3mm neodymium bar magnets — 12x.M3x10mm screws (yellow) — 2x.M3nS square nuts (green) — 2x.#8 or...

The rest of the parts used to assemble these items would be designed and 3D printed in the design phase.               Based on the information provided by Rober’s video and past teams in this course, the goal was to design a car that would be...

This method is the easiest to set up and, in my opinion, the one that works best.It's important to state, that not all models are compatible with each other. The compatible ones are listed here referring to their file names:</p><ul><li>“thin...

No commandline parameters required.That's it!As always I include the OpenSCAD source file for you to adapt and/or improve:Download and install OpenSCAD from https://www.openscad.orgLaunch OpenSCAD and open the enclosed OpenSCAD source file...

It can be used as a piano by using the mp3's I have provided or can be a soundboard by placing your own mp3 files on the SD card.&nbsp;UPDATE:For anyone who downloaded the Arduino code before the Nov 5th please download the one available now...

It's easy to remove though.Beak/BillSince this is a thin part in a light colour, it may benefit from an extra layer or two or denser infill. ...Experiment with your filament, but decide before you assemble as removing it from the Head is a destructive...

Follow the official guidelines and advice's of your country medical professionals as best as you can. Commercial and professional masks of this kind are better then any of these kinds of DiY items. If you can buy or get those use those instead. If...

There are a couple of internal leaf springs, and there's no guarantee they'll work properly if printed in PETG , ASA, etc.. I recommend 0.2mm layer thickness. Print one of each part. No supports are needed, but note that the rack has a small built-in...

For more information on how to create a customized bearing peg scroll to the bottom of Print Instructions. Single mount hole: 'I' design elegant but tricky to mount 'L' design is easy to mount Two mount holes: 'Slim' design, minimal side...

... again. When you turn off the voltage, the non-backdriveable screw will maintain it's grip on your object. Note that the exposed part of the big gear makes a handy thumbwheel for manually adjusting the gripper open or closed. Category: Robotics

That´s why the result is so colourful as I swapped filaments up to six times per print. Saving filament to prevent wasting even more filament, one could say. :D</p> <p>So, please stop printing useless calibration cubes to setup your steps. Do it...

Jojo's Bizarre Adventure Stone Mask STL File 3D Printing File This is just the STL files to be able to print your own mask on a 3D printer. Files Type: STL The mask is ~270mm high,~167mm width and ~135mm depth. This mask can be scaled to fit...

This is a desk mount headphone holder with a ratcheting cable spool. The desk mount is remixed from philbarrenger's awesome "Monster Mouth Headphone Holder - Clampable" ( https://www.thingiverse.com/thing:1657541 ), and the rest is a remix of my...

Does not disturb the sleeping person's sleep. Filters the air from harmful gases and dust Additional internal mesh holder to accommodate impregnated nasal breathing aids or textile filters inside the device. The Anti-Snoring Clip is specially...

It's also the same aspect ratio as is used by all of the document camera apps that I tried. The back of the glass is painted white, with a light magenta tint to balance the green tint of standard silica glass. You can actually buy a special optically...

The second goal of this build was to keep the possibility of converting back the coreYX to&nbsp;Ender 3 V2 and here we are.The benefits of CoreXY system is that your ender 3 v2 doesn’t have to move the heavy glass plate anymore, so by addressing this...

It was at the end of the 90's and the chair had been manufactured in 1996 (I was then 4 years old - can you imagine that ^^ ).After more than 20 years of use in my life (college, high school, university, jobs, 2 evil cats…)…my chair had suffered from...

Update 13: (Feb 19, 2020) Replaced yesterday's suspension update with version 4 (Chassis Inner L4.stl and Chassis Inner R4.stl), as a test print revealed that I forgot to insert the infill in the leaf springs, resulting in those collapsing. I...

The segments are the same under both algorithms, it's just a different way of assembling the whole spiral. Notionally, one would hope that this is a smidge more efficient, but the downside is that openscad has trouble showing the thread built this...

File name(s): For the Mars Base Design MakerBotMars_Mars Acropolis.STL (Optional) For Shuttle Model to print and use with Mars Acropolis MakerBotMars_Mars Shuttle_Optional_for Mars Acropolis.STL Thanks for your consideration, and best of luck to all...