anycubic i3 mega s dual extruder upgrade 3d models

Anycubic I3 Mega S need: some screws and nuts 4020 fan Material: PETG/PLA type: Plug and play from original printer set

This is a little upgrade for your stock extruder ( feeder) of the Anycubic I3 Mega M to make the filament insert a little bit easier. It's really hard to change or insert the filament with the stock feeder, and if you dont want to replace the whoie...

I was a bit bored, so I designed upgrades for my i3 Mega. I splitted the changes so that it´s easier to find. I havn´t uploaded all of them because I´m still printing and woking on some of them. So some parts may still change in the future. ... Direct...

Upgrades for my Anycubic i3 Megaa) Direct Extruderb) Cable Chain Y Axisc) Top mount for the filament sensorV1 with the original radial fanV2 with a 5010 radial fanthe difference is only the fan mountDirect Extruder:Hotend V540x40x10 Fan Original part...

Upgrades for my Anycubic i3 Megaa) Direct Extruderb) Cable Chain Y Axisc) Top mount for the filament sensorV1 with the original radial fanV2 with a 5010 radial fanthe difference is only the fan mountDirect Extruder:Hotend V540x40x10 Fan Original part...

If you upgrade to an e3d v6 and want to print at higher speeds like 80mm/s+, your extruder may start clicking and skipping steps. So a motor upgrade can help out greatly. It will enable your extruder to push more filament with ease. In my case, I...

Hello, I created this handy device to adjust the extruder to the "open" position, allowing me to effortlessly wind the filament onto the spool without having to halt the clamp.

Hello, I designed this little tool to fix the extruder in the "open" position so i can just roll the filament up to the spool without having to stop the clamp. Hope you find it as useful as me :) Category: 3D Printing

This is a cable holder for the Anycubic Mega-S printer. It is placed in front of the extruder Motor. Fillament and cables will no longer rub against each other. The cable is held and in a good and tight position. The holder is very strong. ... To...

Create a new profile with dual extruders in Simplify3D. 7. Set up the toolchange script according to the provided instructions. Please note that this is a complex project that requires knowledge of Arduino and Marlin code, as well as experience with...

If you want to support my work please donate something at this link: https://paypal.me/molinodavide [EN] MY ANYCUBIC I3 MEGA-S UPGRADE GUIDE Surfing the Internet I've found just half of the upgrades that i had in mind for my printer... So I've...

--------------------------------------------------------------------------------------------------------------------------- [IT] LA MIA GUIDA AGLI UPGRADES PER LA ANYCUBIC I3 MEGA-S Navigando in Internet ho trovato giusto la metà delle modifiche che...

Upgrade for extruder

this kit includes everything you need to upgrade your i3megaS from stock to upgraded :)i hope you enjoy it ;)THIS KIT INCLUDES:1-Bed leveling knobs2-Cable clip for hotend cables3-Stepper motor covers4-Sd card grip5-Dinkelmeme Logo plate6-Filament...

Remixed knob to fit the extruder of the Anycubic i3 Mega S.

The arm or lever on the extruder of my Anycubic i3 Mega S snapped and I was unable to manually load or unload filament by hand. It appears that the original is pretty fragile and will likely need to be replaced sooner rather than later. This upgrade...

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

Replacement for the standard i3 Mega S extruder filament guide. ... Use a 2mm drill bit to ensure filament guide hole is correct.

I have the Anycubic M (Anycubic I3 Mega) from 2018 with replaceable drivers: Anycubic M[Amazon EU/DE] Anycubic i3 Mega[Amazon US] But there's also a newer Anycubic S Pro (Mega S) from 2019: Anycubic S Pro[Amazon EU/DE] Anycubic Mega S[Amazon US] (if...

Anycubic i3 Mega / i3 Mega S Direct Extruder Designing a direct extruder for the Anycubic i3 Mega and i3 Mega S printers has proven to be a worthwhile endeavor, offering significant benefits while minimizing stress on the X-axis. The advantages of...

heater cardrige: https://de.aliexpress.com/item/32960167491.html?spm=a2g0s.9042311.0.0.57c24c4dFoRiKv thermal sensor (same as stock but different packaging): https://de.aliexpress.com/item/32847452724.html?spm=a2g0s.9042311.0.0.57c24c4dFoRiKv 23mm...

Nobody sells this part that fits the new Mega-S Titan clone, so I had to remix it from scratch using other parts. Note, not shown in the picture: I added a bit of tubing for the inlet to make the filament flow extremely smoothly. Check out the...

From the ground up, I revamped the project based on MakeNGrow's design, modifying the filament hole to accommodate an adapter specifically tailored for TPU filaments' flexible nature. ...Meanwhile, I strengthened the structural posts surrounding the...

Until then, I'm just going to post this stuff separately in case someone can make use of it.I bought a cheap MK8 extruder designed for a CR-10 from Amazon, and I used these pieces to mount it to the left side of my Anycubic i3 Mega-S. I've included...

Anycubic i3 mega S / Pro spool

The AnyCubic i3 Mega cabinet upgrade is the rest of the rebuild. A new 24 volt power supply, a MKS Robin Nano V3.0 controller, USB type A extension for USB connection, and a SD Card extender for the micro SD Card on the controller. The power supply...

Set of 2 parts for Anycubic i3 mega 3D printer The heatbed cable holder and Y carriage holder are designed for easy printing, requiring no screws or joints. Simply print and snap them onto the heatbed as intended. ... Visit the full collection at...

Plug and play upgradeNeed: some screws and nuts (M3)4020 radial fanoriginal extruder and motor from original printer

I designed an upgraded file, based on daridima's original creation: https://www.thingiverse.com/thing:3108771. With my upgrade, you can superimpose the original media over the new ones I created, conserving space in your printer. ... Dimensions: 30 mm...