anycubic i3 mega s belt tension 3d models

I've attached the OpenSCad sources for easy customization because my Anycubic doesn't have a bottom enclosure, so the fan has enough room. ... It's an easy print, just turn it on the flat side and add support from printbed only (probably will print...

Nobody sells this part that fits the new Mega-S Titan clone, so I had to remix it from scratch using other parts. Note, not shown in the picture: I added a bit of tubing for the inlet to make the filament flow extremely smoothly. Check out the...

Altered the dimensions to better fit the frame of the Mega-S. Added a corner relief and a lead-in on either end for the frame corners. Infill doesn't seem to matter too much, especially if you add more walls. **UPDATE** It might be a bit too long...

Meine Version der Kabelführung für den Anycubic. Zwei Dateien stehen zur Auswahl, einmal für links und einmal für rechts. Viel Spaß damit. My version of the cable management for the Anycubic. There are two files to choose from, one for the left and...

A simple Spool Holder for the Anycubic. The Screws must be a bit longer than the original. The Carton Filament Spool will rotating more easily than the original Holder. it is also a bit wider. ... Need no Support

I'm fed up switching between PLA, PETG, and TPU filaments, which can be a real pain when it comes to adjusting the tension with that tiny wheel. ...To simplify things, I designed a tool using Fusion 360.

Jedynie co będziemy potrzebować to dwa łożyska RJ4JP-01-08 x2 (lub łożysko oryginalne z Anycubic) oraz Prowadnica liniowa średnica 8mm (długość minimum 400mm), 4 śruby M3x25. ...Proszę użyć orientacji jak na zdjęciu oraz opcji "drukuj płasko" nie wymaga...

Hi Makers, because I'm using a y-belt tentioner, theres not enough space for a frontal heatbed handle. So I decided to create a sidehandle. You can use it on both sides. Just turn it upside down before printing and you don't need any support. ...

This cable fixation bracket provides a snug fit on the hotbed mount sub-plate, safeguarding soldered hotbed connections that are known to be problematic on Mega series printers. Installation: To install this bracket, I recommend removing the hotbed...

It's a hotbed cable guide

The tools holder mounts securely to the left-hand side of the printer's frame, which features a minimalist design.

I got a MOSFET Board with uncommon dimension, So I re-designed the whole. ... For MOSFET with 41.5mm x 51.5mm borehole. The design is inspired from Max3D-Druck's Mosfet Mount.

I took inspiration from https://www.thingiverse.com/thing:3930311 and decided to make a few tweaks to ensure there's ample space between parts, so I modified the design to clip from the very top instead of relying on clearance alone. ...Unfortunately,...

From the ground up, I revamped the project based on MakeNGrow's design, modifying the filament hole to accommodate an adapter specifically tailored for TPU filaments' flexible nature. ...Meanwhile, I strengthened the structural posts surrounding the...

To better control the filament at Any, turn the extruder's mounting angle and attach this holder. A M3 threaded insert is required for the holder. The large depression can be used for a 14x4mm magnet, but it is not typically needed. ...Position the...

... light for standard LED strips. ...It's mounted on the hotend cooler fan and competely hidden inside the hotend (original or honeycomb) and compatible with the dual-side part cooler. ...LEDs can be connected to fan power or wire them to 12V of the PSU.

I'm thrilled to share that I've created my very first piece using Cinema 4D, specifically designed for my 3D printer. ...I've utilized CURA's capabilities to precision-cut the design. ...I must say, I'm absolutely delighted with how it turned out!

Surprisingly, the mainboard's power consumption is very low when not driving the hotbed or hotend. As a result, you no longer need oversized wires. ... This holder fits seamlessly with the stepper driver fan duct and Noctua fans, which can be found on...

... and made room for my go-to pliers. The smallest hex key is a snug fit but it stays put. I also beefed up support between the attachment and the tray itself. You can never be too sure if it was needed, but it's always better to be safe than sorry.

We design a lock that secures your patio umbrella in place when tilted to block out the sun's intense rays. Crafted specifically for 37mm umbrella poles, this solution may also work on sizes ranging from 36-38 millimeters, although thorough testing...

If you've found this solution helpful, consider supporting the development of more innovative products like this one by donating what you think it's worth through our PayPal account. Your contribution will help offset the time and effort invested in...

I designed this magnet holder for the Raspberry Pi 3/4 touchscreen from "Phillip's 3D Print Shop" because I wanted to place the touchscreen without drilling anywhere on the frame. This is secured with a Neodym magnet glued into the holder and...

When I installed Itlowe's Y tensioner, I had to remove my old hotbed handle because it would get stuck, so I decided to design a compatible one. It also lets you adjust your BIG printed leveling knobs with ease. ### The light one (Side_handle.stl)...

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

A two-part clip-on holder for a digital caliper on the AnyCubic i3 Mega printer.

Here is a bed holder for the Anycubic I3 Mega or Mega S printer. Unfortunately, so far none of them fit correctly because they are too loose. ...To solve this problem, I designed and built my own version that fits perfectly and is easy to install...

Model for Calibrating the Print Bed on an Anycubic MEGA-S 3D Printer

I have the Anycubic M (Anycubic I3 Mega) from 2018 with replaceable drivers: Anycubic M[Amazon EU/DE] Anycubic i3 Mega[Amazon US] But there's also a newer Anycubic S Pro (Mega S) from 2019: Anycubic S Pro[Amazon EU/DE] Anycubic Mega S[Amazon US] (if...

The Anycubic i3 Mega / Mega S frame mounts a versatile toolholder that offers ample space for essential tools like scrapers, tweezers, and clippers. This handy holder is designed to be easily integrated with the printer's frame, providing users with...