anycubic i3 mega fan 3d models

I put a large fan on the bottom of my 3d printer because I wired in a computer power supply. This caused the original legs to be too short. This was my way to fix it. I'm sure 30% infill would be enough but I did 100% for extra stability. ...I also used...

... than its metal counterpart, allowing for potential space to accommodate a bl touch sensor while offering improved visibility of what occurs at the nozzle tip. ...Designed to be compatible with existing holes and original fans. ...Layer 0.2 Infill: 100%

For Reference, My K8200 Printer's Decibel Levels Are: dBA at 100% fan speed: 38 (average), 48 (peak) If You're Interested in Creating Your Own Custom Hotend Cover, Here is the BOM for This Project: 4 x M3x20 Screws (for fans and front plate) 2 x...

I'm utilizing a Thingiverse design (https://www.thingiverse.com/thing:2815388) for part cooling, which relocates the fan behind the print head assembly and significantly expands the hotend area. However, I've encountered an issue - there's no...

I needed an increase for my printer so that I can maybe put fans underneath it later. I printed them out of pla. Maybe you can also print them out of TPU or something similar so that you have vibration dampening. You can leave the original feet...

My enhancements: The left fan hole now features a fixed grid and I've maximized the mother holes to their full potential. Additionally, I modified the nozzle opening to facilitate easy rotation. ... Component cooler:...

You can combine the led wires with the cooling fan. I also used a Noctua and it works perfect. This Version use a 45° corner for the bar-holder, so the light shines more to the center where the nozzle is located. Tip: use a thread cutter for...

... already be properly positioned. I use Cura, so my testing has only been done with that software. To minimize the risk of blowing the mount over, I position the model at a right angle to the fan. ...So far, I have printed three successful mounts.

This component cooler is intended for use with the original radial fan. The existing one-sided air distributor can easily be exchanged for this one. You only need two M3 nuts. There is also the option of sawing off the lower part of the existing...

The fan that cools the filament as it's laid down can sometimes blow small fragments of filament towards the right side leadscrew and end-stop, which may lead to malfunctions over time. Duplicate this part in your slicer software to ensure a perfect...

The Anycubic on Boot talks to the wifi module with AT commands at 115200bps, sends an AT command to switch at 2.250.000Bps and opens UDP server in port 3000. This is a sniff traffic on port, commands sent from Printer. Boot printer and it sends at...

Update : This part works well but be aware that if you start the print with your part fan going 100% the air blowing on the side of the part might cause the print to come away from the bed. Either start at 10%-25% like I do or maybe increase the heat...

The fan that cools the filament as it's laid down can inadvertently blow small pieces of filament onto the right side leadscrew and end-stop, potentially causing them to malfunction over time. Duplicate this part in your slicer to ensure a seamless...

Update : This part works well but be aware that if you start the print with your part fan going 100% the air blowing on the side of the part might cause the print to come away from the bed. Either start at 10%-25% like I do or maybe increase the heat...

The fan that cools the filament as it's laid down can blow small particles of filament onto the right side leadscrew and end-stop, potentially causing them to malfunction over time. Duplicate this part in your slicer to ensure a perfect fit with the...

... ...The fan that cools the filament once is its layed down, can blow small pieces of filament to the right side leadscrew and end-stop, which might make them malfunction over time. Mirror this part in your slicer to make fit it the other stepper motor.

1x https://www.amazon.com/dp/B07DXRNYNX/ref=cm_sw_em_r_mt_dp_U_2EtWBb13J7ARW 1x https://www.amazon.com/gp/product/B07B2SLYXN/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1 1x...

I did install the upgrade kit for the I3 Mega (TITAN-Extruder and Filament-Rack) - the kit is really worth checking out: https://www.amazon.com/gp/product/B07KLJJYNV/ref=ppx_yo_dt_b_asin_title_o05__o00_s00?ie=UTF8&psc=1 But the filament holder falls...

After swapping out the fans on my i3 Mega, I decided to tackle other sources of noise as well. The result is my Silent Filament Guide, expertly paired with my Spool Holder. Thanks to the PTFE tube inside its housing, it won't generate unpleasant...

I tried to find a spool holder for my i3 mega but did not end up with one that worked as I wanted, so here we are again and designed one that was more suited for what I need. So I wanted a roller model and after the first few prototypes, I ended up...

I'm using it on my custom Anycubic I3 Mega, but it should work on all types of Prusa printers with this mount: https://www.thingiverse.com/thing:926794. The fan duct isn't ideal, but it works. Unfortunately, it's not as good as the stock one. If I'm...

I used a previous chain design as inspiration; I believe it was this one: http://www.thingiverse.com/thing:1735193 Print Settings: Printer: Anycubic Mega i3 & Omega i3 Rafts: No Supports: Yes Resolution: 0.2 or 0.3mm Infill: 20 or 30% Notes:...

Fan assembly requires two 25mm spacers and several M3 fasteners.

Fan Mount upgrade for Anycubic Mega S with tall stepper driver heat sinks. Created to accommodate the taller heat sinks of some stepper driver upgrades instead of bending the fan stock fan mount. You will need some #8 machine screws and nuts to...

IMPORTANT: Use 5V fan in the hotend (tested) The change in this Remix was the I3 Mega for Mega S and other no named With this fan mod you can use two 40x40x10 fans Update Experimental BL Touch ( No Tested ) Plz Give me Feedbacks Update 22/11/20 BL...

Since I converted my printer very fast to the Bowden MK3 R3 X-carriage for the Anycubic I3 Mega or Anycubic I3 Mega Prusa i3 X-Carriage Converter, of course, the Schleppkette / drag chain design of Michelx no longer fit. I worked with this thing from...

With my quick conversion to the Bowden MK3 R3 X-carriage for the Anycubic I3 Mega, or the Anycubic I3 Mega Prusa i3 X-Carriage Converter, it was clear that the Schleppkette / drag chain design of Michelx no longer fit. However, I found a great...

Verbesserungen Anycubic i3 Mega S,X,Pro.

Anycubic i3 mega aeration & anti vibration system

Nozzle cooling duct for Anycubic i3 Mega. ...