anycubic i3 mega fan 3d models

Fan covers to fit on an "opened" original I3 Mega hotend housing.\r\nThey work with the original screws and fans if you prefer.\r\n\r\nPrinting will take around 30 minutes with a speed of 40mm/sec and layer height at 15mm, consuming approximately 2g...

... ...I simply eliminated the slight lip that made it hard to place the radial fan properly. ...If you prefer, you can still use the original design and just trim off the excess after printing - a minor time-saving measure that takes about one minute.

This setup is tailored specifically for a pair of 40mm Noctua fans. As a result, the printer operates in near silence, with airflow evenly distributed across all components. ... To complete this configuration, you will still need to acquire four M3x20...

I made some tweaks to the fan cooler design, specifically shortening it so that the ring clears the nozzle by a hair. It's close, but it does manage to clear the print just barely. Additionally, I went through and cleaned up errors in the original...

Fan Holder for Anycubic I3 Mega S

... fan duct from H_Run. ... I created a wrap-around ring with 270° exhaust ducts. I also removed a small cutout, which is why the original did not fit my printer. This remix is for the Anycubic i3 Mega S (2020). ... Printable without any support.

New cooling fan bracket (v.2 - looks pretty rough, but delivers better airflow for both sides) for the Anycubic I3 Mega printer, using a Noctua 40x40x20mm cooler. If it's too tricky to print as one piece, you can easily split the bracket into two...

This upgrade replaces the cooling fan holder for the AnyCubic i3 Mega, addressing a major issue with airflow, an inadequate fan guide, and a piercing whistle that can drive anyone mad. Despite being the first upload of this part, it has undergone...

The Anycubic i3 Mega S requires an upgraded cooling solution, which involves replacing its bizarre stock driver board cooler with a more efficient one. This may necessitate re-seating the heatsinks, ensuring that their fins are perfectly parallel to...

A 120mm fan bracket for the stepper drivers and mainboard of the Anycubic i3 Mega S.Inspired by:https://www.thingiverse.com/thing:3441556https://www.thingiverse.com/thing:2924058Unfortunately, the existing brackets didn't fit. Therefore I constructed...

I ordered two 80x80x10mm fans at Amazon because I needed another mainboard/stepper cooler for silencing my i3 Mega after replacing the stepper driver with TMC2208. The only option available for next day delivery was these:...

### Starting This is part 2 of my airflow concept for the Anycubic I3 case. Part 1: Anycubic I3M - PSU Cover NOCTUA 60x25 https://www.thingiverse.com/thing:3441468 Part 3: Anycubic I3M - Double MOSFET 3D-Freunde with NOCTUA 40x10...

I attempted an off-the-shelf fanduct but it wouldn't match my i3 Mega - S fan, so I chose to construct one from scratch. Furthermore, I noticed that many of the other available fanducts sit too close to the nozzle, which can lead to a burnt fanduct...

After the standard mainboard fan was the last noisy part in my I3 Mega after several "silent mods", I decided on the 50mm double fan version from "mariusbach": https://www.thingiverse.com/thing:2953960. Why I chose this option, I'll explain below...

Double Fan Holder for 2 50mm Fans, Silence for the Motherboard. ...You need 2 M3x20mm Spacer for mountig and some m3 screws

Silence Enhancer Mount for Dual 50mm Fans - Protects the Motherboard from Noise Pollution. ...To Assemble: Secure Two M3x20mm Spacers to Hold the Fan Holder in Place, Then Tighten with M3 Screws.

... to fit my setup perfectly, pairing it with a 3D-Freunde Mosfet holder right beside it. ...This custom holder utilizes the two original mainboard fan screws while placing both fans incredibly close to the mainboard, mere inches from the SD-card cable.

... fit my setup with the 3D-Freunde Mosfet holder right next to it (thing:2845377). ...This holder uses the two original mainboard fan screws but places both fans closer to the mainboard (right next to the SD-card cable). ... Category: 3D Printer Parts

14/04/2021 --> v1 I blocked the hot air from reaching the cooling fan from the heatsink and remodeled the fan tubing to better focus the tip of the nozzle. Feel free to test it and send me any suggestions! ... Props to H_Run for the great share.

... ... 14/04/2021 --> v1 I blocked the hot air from reaching the cooling fan from the heatsink and remodeled the fan tubing to better focus the tip of the nozzle. Feel free to test it and send me any suggestions! ... Props to H_Run for the great share.

To replace the stock hardware, you need to swap out both the part fan holder and the hotend fan holder since the original metal holder is a single bent piece of metal. Fan Holder: https://www.thingiverse.com/thing:2538250 You will require some...

This fan is about 5mm wider than the stock fan so the housing needs to be replaced. I used bolts on the back (glued in). But the top should be fine screwing directly into the plastic. You can just cut the plug off the stock fan and splice it onto...

The fan holder can be mounted with the screws of the old metal holder, but I used the longer screws that held the old fan. The holder should also be glued onto the "ceiling" using double-sided tape to avoid vibrations altogether. You can use the...

Redesigned with the following modifications: **For optimal ventilation its recommended a hole be cut on the bottom steel plate to allow air for the fan, I used a dremel to cut identical shaped slots.** 1. Dual 40MM fan mounting positions so both the...

This is a minor revision of this project: https://www.thingiverse.com/thing:3234293 or https://www.thingiverse.com/thing:3224780 for an additional splash of color on the hotend case, a vibrant fan grille to make the hotend even more stunning. ...Sorry...

This is a custom fan box designed to fit snugly on the left side where some holes accommodate the PSU. I created this enclosure because I wanted to bring in fresh air from outside, rather than relying solely on the enclosed environment. As for the...

You can find this and other projects at https://www.tinkercad.com/things/03NEJunad0e-anycubic-i3-mega-s-fan-stock-drivers-duct. ...Thanks for checking it out!

Setting up the blower, I secured it to the extruder housing. Next, I noticed a gap between the extruder housing and the blower (it turned out that I had pressed the blower too tightly against the housing). Loosening the screws reduced the gap, but it...

User installed a high-performance ventilation system featuring a sleek, unbranded design and advanced airflow technology.

A remix of the https://www.thingiverse.com/thing:2823129 that adds a BL Touch Mount on the right side of case. ... You need to configure the XY Probe position in your firmeware or using the M851 GCode.