anycubic i3 mega driver upgrade 3d models

Anycubic i3 Mega Filament Driver This filament driver and protection system prevents filament from dropping off the spool when retracted multiple times in a row. ... It works with: * Side Extruded Support (Thingiverse ID: 2448418) * Spool Holder...

The AnyCubic i3 Mega cabinet upgrade is the rest of the rebuild. A new 24 volt power supply, a MKS Robin Nano V3.0 controller, USB type A extension for USB connection, and a SD Card extender for the micro SD Card on the controller. The power supply...

Set of 2 parts for Anycubic i3 mega 3D printer The heatbed cable holder and Y carriage holder are designed for easy printing, requiring no screws or joints. Simply print and snap them onto the heatbed as intended. ... Visit the full collection at...

An accessory for standard Anycubic spool holders with ball bearings. You will need: 4 M8 flat head screws with countersunk heads, 16mm wide and 22mm long 4 M8 nuts 4 8mm x 22mm x 7mm ball bearings (inner diameter x outer diameter x width) 8 washers...

A fun duct for cooling a stepper driver for anycubic i3 Mega S

A better system to cooling the Stepper driver of Anycubic i3 Mega S with radial fan 5015

A better system to cooling the Stepper driver of Anycubic i3 Mega S with radial fan 5015

Direct airflow over stepper drivers in Anycubic I3 Mega by ducting it out the side of the base is crucial. The internal duct clearance is generous, allowing for aftermarket stepper drivers with oversized heatsinks to fit comfortably. This design...

--------------------------------------------------------------------------------------------------------------------------- [IT] LA MIA GUIDA AGLI UPGRADES PER LA ANYCUBIC I3 MEGA-S Navigando in Internet ho trovato giusto la metà delle modifiche che...

If you want to support my work please donate something at this link: https://paypal.me/molinodavide [EN] MY ANYCUBIC I3 MEGA-S UPGRADE GUIDE Surfing the Internet I've found just half of the upgrades that i had in mind for my printer... So I've...

This is a comprehensive guide to upgrading a Prusa i3 Mega 3D printer, specifically focusing on improvements for better print quality and reliability. The author has spent several months researching and testing various upgrades, providing detailed...

EN: This extension allows you to install a diamond hotend on your Anycubic I3 Mega. <b><u>!! I assume no liability or responsibility for this, because this modification will void your printer's warranty. You are solely responsible for modifying your...

While I once considered the possibility of a complete printer replacement, this upgrade has revitalized my Anycubic i3 Mega, and I am excited to continue using it for many more years to come. I hope you find this upgrade as rewarding as I have, and...

I upgraded my Anycubic i3 Mega with an E3D v6 clone of very good quality (http://s.click.aliexpress.com/e/bqbS2KS9). I started following the guide of steddyman (https://www.thingiverse.com/thing:2539301/files). Unfortunately the dimensions of my...

Here I created a custom mount for the filament sensor that works perfectly with my Anycubic I3 Mega 3D printer, which is upgraded with the new E3D Extruder from the Mega S model. Be aware that this upgrade may not work correctly if you're still using...

I upgraded my Anycubic i3 Mega with an E3D v6 clone that's truly exceptional in quality (http://s.click.aliexpress.com/e/bqbS2KS9).\r\n\r\nFollowing steddyman's guide (https://www.thingiverse.com/thing:2539301/files) was the next step.\r\nDimensions...

This is a little upgrade for your stock extruder ( feeder) of the Anycubic I3 Mega M to make the filament insert a little bit easier. It's really hard to change or insert the filament with the stock feeder, and if you dont want to replace the...

The Anycubic I3 Mega Pro now comes with a spool holder. But the coated metal is very grippy so I made this thing to put the spool on two ball bearings to reduce the friction. You need 1 8mm rod or M8 rod and two normal 608Z ball bearings. ... Category:...

The Anycubic I3 Mega Pro now comes with a spool holder. But the coated metal is very grippy so I made this thing to put the spool on two ball bearings to reduce the friction. You need 1 8mm rod or M8 rod and two normal 608Z ball bearings. ...

I was a bit bored, so I designed upgrades for my i3 Mega. I splitted the changes so that it´s easier to find. I havn´t uploaded all of them because I´m still printing and woking on some of them. So some parts may still change in the future. ... Direct...

Based on our CR10/Ender Mod kit this is a fundamental frame arrangement for the Anycubic Mega i3, with plans to release a collection of parts in the future to support this project. The design accommodates the E3DV6 Hot end and most excellent...

I really enjoyed the trash can design for my Anycubic i3 Mega (https://www.thingiverse.com/thing:2835257). I printed it and used it for a while, getting lots of pleasure from it, but only as long as the basket with the garbage didn't fall to the...

Upgrades for my Anycubic i3 Megaa) Direct Extruderb) Cable Chain Y Axisc) Top mount for the filament sensorV1 with the original radial fanV2 with a 5010 radial fanthe difference is only the fan mountDirect Extruder:Hotend V540x40x10 Fan Original part...

Upgrades for my Anycubic i3 Megaa) Direct Extruderb) Cable Chain Y Axisc) Top mount for the filament sensorV1 with the original radial fanV2 with a 5010 radial fanthe difference is only the fan mountDirect Extruder:Hotend V540x40x10 Fan Original part...

You can find nuts covers for bed leveling here: https://www.thingiverse.com/thing:2843274 Also, check my I3 Mega ULTIMATE upgrade guide, which contains valuable knowledge that may help you achieve optimal results. You'll find it here:...

This is a comprehensive guide for modifying an AnyCubic I3 Mega 3D printer to allow multicolor printing, specifically a two-color and three-color setup. The modification involves installing a new hotend and mainboard, as well as flashing the...

This printer is incredible and never needs any upgrades, I personally don't buy printers only to discard plastic on "upgrades", if that's what I want then I would build my own printer...\r\n\r\nHowever, this one from Anycubic should be updated with...

Because the standard extruder holder isn't perfect for the 48mm upgrade, I designed a new holding system that works great in my situation and also stabilizes the weight in the middle of the Z-axis. This upgrade also allows for cable management and a...

this kit includes everything you need to upgrade your i3megaS from stock to upgraded :)i hope you enjoy it ;)THIS KIT INCLUDES:1-Bed leveling knobs2-Cable clip for hotend cables3-Stepper motor covers4-Sd card grip5-Dinkelmeme Logo plate6-Filament...

I loved the concept of upgrading my printer with an LED light, but since it prints throughout the night, I needed a button to turn off the light. So, I combined the ring design with a switch and mounted it to the side of my printer. For those who are...