anycubic hot end 3d models

(I tried to keep-up with Nopehead's highest standards) Marlin must support multi extruder with a single hot end feature. Prometheus extruder web site has a good guide for upgrading Marlin. Tip: tubing that goes inside E3D hot end should have an...

(I tried to keep up with Nophead's highest standards) Marlin must support multi-extruder with a single hot end feature. Prometheus extruder web site has a good guide for upgrading Marlin. Tip: tubing that goes inside E3D hot end should have an...

Just another design of the Ender 3 V1 Hot Ender Cover.

After finishing the process, do a PID tune on your printer because the previous tune is accounting for the heat sink fan blowing on the hot end. There are many videos on doing a PID tune on Youtube if you don't know how to do it. Most things are...

Inspired by 3Deth's and RICBRU's work, I've designed my own CR-6 SE air intake with two-tone air deflectors.I'm not sure if this surpresses any noise...it's just designed to look cool while redirecting the vent to pull colder air from above the hot...

Print: - E3D End Effector - E3D Double Duct housing - E3D Hot End cap - (2) Part fan ducts (mirror the part in slicer to print both sides) You'll also need: - 4 M2x5mm (2 for the box fan, 2 for the air ducts) - 2 (or 4) M3x16mm (3030 fan) - 2...

It reuses the screws from the hot end radiator, but they only work if you remove the washers. It's designed for left and right 30x30x10mm fans (12v) but you could get by with just one. If you add the left one, then you need to use my custom x stop. I...

This movement is not an issue during the leveling, but this “flex” allows the nozzle to be moved DOWN towards the bed during extrusion, due to the force of the extruder pushing the filament into the hot end. The amount of DOWN movement, towards the...

For as long as I've owned my Printrbot, I've searched high and low for an effective fan shroud to improve airflow around the hot end. Many solutions have been presented, but every single one required removing the metal hotend cover, which I still...

This hot end is quite heavy so consider lowering the print speed. This is just an experiment as I think it's probably not a good idea but who knows... I tried to get the center of gravity as close as possible to the lower mount. The cooling fan is...

Note I won't print this until Monday so here's a prototype of the bottom part of a case I've been designing for a few days; I just happen to have a spare hot-end for my HicTop 3DP-11 and I'm getting more spare parts in over the next couple weeks. As...

Updating the CR10 V3 to use the V6 hot end by E3D. Modified Marlin Firmware is included. ***Glitch with Z-Offset, please follow video instructions for details*** ***Fan Mount Has been updated to allow for more room for the screw.*** I...

Hot End Fan Duct: Works for E3D V6 Heatsink or Clone. Can be used with 40mm fan directly and you don't need the original E3D 30mm fan duct to put on an adapter. I printed it face down with simple touching build-late support and maybe support is not...

... model's mounting bolt pattern is not accurate (Slightly too wide). That said, they did a good job modeling the collet and collet clip, so I took those two items and imported into my design. My hot end model was verified against the actual product.

Color mix hotend: Three-in-one-out hotend available at https://item.taobao.com/item.htm?spm=a1z3i.7c.footer.4&id=531968680133 This all-metal 3D printer hot end from North Five is a game-changer. For firmware and software tool, visit...

I had trouble with Luke's hot end fix on my Ender 3 Pro because whenever I tried to get the filament up to the nozzle it seemed to get jammed. I hypothesized that the washer was moving around and not staying concentric with the tubing. Tried a few...

 I wanted to not have something in the way of a CL touch using the CL touch bracket, and I wanted the cover to be magnetically held on so I can easily access the hot end.  This cover and shroud design features (2) 3010 blowers, available on...

Watch attached video for details. Luke's hot-end fixes are quite popular, and for good reason. You can get the details on needed length of PTFE tube, a link to a specially designed tube cutter, and more at the original thing: <a...

This hot end is quite heavy so consider lowering the print speed. This is just an experiment as I think it's probably not a good idea but who knows... I tried to get the center of gravity as close as possible to the lower mount. The cooling fan is...

This is, theoretically, a mold for making a silicone sock for the Mosquito hot end. Disclaimer: I'm completely clueless about this, but I've watched a bunch of YouTube videos on it, so that makes me an expert in internet terms, right? ***Removed...

Regardless, I've replaced all TMC2130 V3.0 SPI boards, fans, hot ends, and rewired everything basically from scratch. I also wouldn't recommend putting the control board under the Lack Table enclosure - it's a nightmare to work on. Here's a video...

1 40mm fan for cool end 1 60mm fan for print object

Looking at the Ender series extruder cover, you realize that they just designed that extruder cover which hosts both hot-end fan (HEF) and print fan (PRF), as simple as it could be and without considering the airflow of the fans which is very...

Broke three of my hot tub clips, left me scrambling to find replacements that just aren't out there. Spent one late night designing a solution and after tweaking it a few times, this clip is working flawlessly. Keeps the lid securely in place even...

I opted to acquire additional high-temperature ends for my Raise3D N2 printer to accommodate various nozzle sizes, finding it more convenient than frequently switching out the nozzles. ...Consequently, I required a means to store the unused nozzles...

... minimal supports, use infill or don't idc. Remixed from some Russian guy's design (thing:4784950) but his was for different fans. Goodluck and Godspeed PS: I highly recommend TH3d's tough tube, I've been printing pretty hot and it hasn't degraded.

I repositioned the "Arm" bracket to prevent the drag chain from colliding with the vertical aluminum stock when the X-axis reaches zero position, also increasing its height to match that of the mounting bracket at the opposite end of the drag chain.

project cable management backplate mount for tronxy x5s the idea is: use the RJ45 for all the sensor, thermistor and fan cables the XT30 for HE-cartridge and you kinda get a quick release or hot swap carriage for a tidier look and less wear and tear...

... Here only stand for the rest of the parts and detail instruction please refer to original thing To setup it: unscrew one screw and put on stand and tight screw back from top. After that ou can set end into dove tail slot. Thats it. ...

Note the fan hits the side in its lowest setting, taking up a little room, and because of the loop at the end, it really doesn't do much from the original build, so keep an eye out for a remix coming soon. For more information, please visit us online...