anycubic extruder 3d models

Full cover for plug and cables for the Anycubic i3 Mega extruder. -The front door and the top circle give easy access to the plug and filament entry. -Easy to print (no supports) -Front door ready for 5x1mm magnets. ... I hope you find it useful!

The Anycubic i3 Mega extruder gets a comprehensive cover and cable system. This setup makes accessing the plug and filament entry a breeze through the front door and top circle. Printing this design is effortless, requiring no supports at all. ...The...

Upgrade for extruder

This is replacement part for Anycubic Mega S, cracked original Titan extruder lever. Compared with source, I made couple of changes: - adjusted hole sizes for better fit - reinforced parts, especially in place, where the original part had cracked ...

... too high for the structure, so it cracked at the first angle from the top. That's why I added the reinforcement ridges. Print Settings Printer: Anycubic i3 mega Rafts: NoSupports: No Resolution: 0,2 mmInfill: 60% Category: 3D Printer Accessories

Here is another version of an Extruder Holder for the Anycubic I3 Mega. This one is placed on top of the printer to feed filament from the right side. Now, I have also designed a new version (https://www.thingiverse.com/thing:3223705) that goes down...

This is a modification for Anycubic Mega-S extruder (not i3 mega). It fix flexbile filament jam between the gear and filament guide, there are big gaps between stock guide and driving gear. I did print it with 0.1 accuracy without supports. After...

This is a modification for Anycubic Mega-S extruder (not i3 mega). It fix flexbile filament jam between the gear and filament guide, there are big gaps between stock guide and driving gear. I did print it with 0.1 accuracy without supports. After...

I upgraded my Anycubic i3 Mega's extruder fans, but now I need to resolder the connectors on the PCB for this modification to work. Alternatively, I could simply relocate the PCB to a different position. To make room for the new fan setup, I created...

Also, you'll need to print this part: https://www.thingiverse.com/thing:2838383 to install this extruder on Anycubic I3 Mega. It may be tricky, but as you can see in the photos, it's possible. **Changelog:** - 19.06.2018 - I made a new fan mount...

IN THAT WAY IT IS AVOIDED COMPLETELY ANY FLEXION OF THE WHOLE SYSTEM. Currently, using nozzle 0.6 I have retractions between 1.6 and 1.8 mm at 50 mm / s Print instructionsUnassociated tags: extruder chiron, mk8 chiron, mod chiron Category: 3D Printer...

A printer extension for the Anycubic I3 Mega that enables printing with flexible filament. ...Make sure to check after installation that the roller facing the gear can still move freely.

Got tired of the print bed pulling the extruder cables so I designed this little clip to address that problem. ...

This is a Simple Adapter to bridge the gap between the Filament runout sensor and the white bowden tube of the extruder. ... Makes guiding filament throught way easier.

A Bracket to Rotate the Extruder for Easy Filament Insertion To accomplish this task, you will need four M4 threaded screws and four M4 nuts.

This adapter plate turns the original existing Bowden extruder into a direct extruder with simple means. The existing mounting bracket is exchanged for this plate and fastened with the two top screws of the X linear guide. I printed the plate out...

This is an adaptation of a compact fly extruder created by Mauro that caught my attention due to its unique design. ...I decided to modify it to suit my own setup and needs.

The Thumb Bar on my extruder broke, so i created a extender that will fit over the stock one to. A: make my repair. B: extended it to make it easier for me to use. ... 2xM3 screws hold it together.

Hello, I created this handy device to adjust the extruder to the "open" position, allowing me to effortlessly wind the filament onto the spool without having to halt the clamp.

The clip locks firmly onto the extruder motor from beside it, its smooth edge gliding effortlessly over the motor's rear as it swings open to make contact. ...Pressing it home secures everything in position, allowing you to carefully guide the harness...

... setup. ...To do this, I disassemble the sensor and adjust the backlight on the print area itself. Additionally, we utilized four LED Piranha lights paired with step-down DC-DC converters to power everything from the fan that cools the extruder.

How to Convert Your Flying Extruder into a Floating One: A Simple Design with Much-Needed Backtension for Extruder Springs. I Tested Multiple Variations and Settled on This Basic Design, Which Effectively Stops Most Violent Shaking Without Adding...

... tolerances, but all screws should still fit just fine. I've also reduced the depth of the extruder mount which allowed me to use the original screws and screw them in properly. ... I'm new to 3d modeling, but I hope that someone has use for this.

This is a modified version of the original extruder for flexible created by Iceman51 with several key upgrades: - A bolt-on screw supports the spring instead of a printed block - The filament hole has been enlarged to accept a 2in/3out mm PTFE small...

The cable coming off my extruder often hit the top bar of the printer when I printed tall objects. Crafted this bracket to mount seamlessly on the existing hardware. Gives it a bit on an angle and keeps the cable back and out of the way. ...

Hello, I designed this little tool to fix the extruder in the "open" position so i can just roll the filament up to the spool without having to stop the clamp. Hope you find it as useful as me :) Category: 3D Printing

For Anycubic Predator Delta Printer rubber bands 4 mm...

Mod reduce step motor temperature and what is more importand cooling filament inside extruder. There are two versions. One with 5015 fan and another with typical 50x10 fan. Both reduces heat very good. For bots fans there is same base. Both part...

I replaced my print of the original side extruder mount, which had cracked when I attempted to attach the Bowden tube, due to excessive force applied with the spanner. ...The stress caused by the wrench was too great for the structure, resulting in a...

I made the hole (where the nut is screwed on) oval-shaped - this increased the amplitude of the model's opening, allowing me to easily put it on and take it off the extruder handles. The bolt and nut were printed without supports, layer thickness...