anycubic driver 3d models

I swapped out that loud 50mm driver fan with an AMD boxed fan cooler. Now the printer is far from silent, but it's definitely less annoying to listen to. The holder fits perfectly, and for improved airflow, I decided to use screws instead of relying...

The Anycubic Delta/Kossel Tri-Gorilla board features a built-in stepper motor driver cooler tunnel that makes printing easier than ever before. M3 screws are included for effortless assembly. ...To ensure optimal stability, supports should be added as...

This is a remix of [Yakandu's Anycubic Kossel driver fan](https://www.thingiverse.com/thing:2774598) with breakouts for the TMC2130 CS and SPI pins, featuring an added fourth breakout for those using TMC2130 for the extruder in addition to X, Y, and...

I've noticed that my drivers tend to run a bit too hot during extended printing sessions, so I decided to tweak the airflow and see if it made a difference. ...So far, it's been working out great for me, but I haven't had the chance to measure the...

Anycubic's innovative Delta/Kossel Tri-Gorilla board features a cleverly designed stepper motor driver cooler, expertly crafted for effortless printing experiences. ...Installation is a breeze due to its straightforward design, requiring only M3 screws...

... fan, connected to port fan1 on the PCB. The fan1 is enabled when the bed heater is activated (latest ANYCUBIC firmware version). I employ this fan duct to cool TMC2208 stepper drivers; my printer remains extremely silent with these drivers.

few perimeters and go print! ...More better performance for cooling. Especially if u replace stock drivers to TMC2208. -- Warning! TMC2208 required to edit firmware. ... -- U may print it with PLA without supports.

Anycubic i3 Mega Filament Driver This filament driver and protection system prevents filament from dropping off the spool when retracted multiple times in a row. ... It works with: * Side Extruded Support (Thingiverse ID: 2448418) * Spool Holder...

It was cumbersome to keep removing the fan bracket to swap drivers as I was having difficulty with the new driver boards. This bracket is meant to accept the hex screws that the original bracket mounts to the frame. You will have to sources 2...

Cooling Tunnel for Anycubic Kossel Trigorilla Board: A Solution for Efficient Cooling. The tunnel is designed to accommodate large heatsinks for TMC2208 & TMC2100, providing ample space for these components. As seen in the pictures, I have...

... were still soaring. ...To address this issue, I created a channel for my StepStick drivers and fashioned a small vent that cools the processor on the board. ...It was a simple yet effective solution that works like a charm and fits seamlessly in place.

Direct airflow over stepper drivers in Anycubic I3 Mega by ducting it out the side of the base is crucial. The internal duct clearance is generous, allowing for aftermarket stepper drivers with oversized heatsinks to fit comfortably. This design...

Cooler for AnyCubuc Stepper Motor. For 2 fans 50x50x10 (I have the Noiseblocker XS-1 BlackSilentFan Fan (50x50x10mm)) installed. Those who take the original screws from the fan, holes must be drilled afterwards. ... A lot of fun printing again.

There are numerous upgrades available for the Anycubic i3 Mega. This is an option to replace the motor driver fan with two 40x40mm fans. You can mount it using the 2 screws at the original fan holder. Additionally, you will need 5x M3x16 screws and...

I wanted to ensure more ventilation for the drivers, so I designed 2x 50x50x10 mm fans, the holder fits instead of the original iron one. the holes at the bottom have a diameter of 2.5, it is better to use an M3 tap and the screws will fit...

Remix from direct drive conversion stock

I installed linear guides in X, then converted my boundtech into direct drives. I took an existing project for a titan clone and adapted it to work with linear guides. I've verified that another fan system is compatible with this project and added it...

I created this modification to enable swapping of the original blower that circulates air above the motherboard, with a focus on targeting the drivers specifically. Update - Changes on my agenda for v2: 1. I plan to reduce the duct's height so more...

A fun duct for cooling a stepper driver for anycubic i3 Mega S

A better system to cooling the Stepper driver of Anycubic i3 Mega S with radial fan 5015

A better system to cooling the Stepper driver of Anycubic i3 Mega S with radial fan 5015

I'm trying to create a cooling fan duct for x,y, and z stepper drivers on my TriGorilla board in my Anycubic Kossel Linear Plus 3D printer. I've been using a cooling tunnel for my stepper drivers, but they're not cooling down the ones in the back...

Please see the remixed file.\r\n\r\nThis mod combines Juha's original Anycubic i3 Mega Stepper Motor fan duct and self_taught's 5015 fan mount, with a redesign from scratch.\r\n\r\nWhat's the difference?\r\nA longer bottom tube where the fan mounts...

Anycubic i3 Mega Stepper Driver Fan für alle gängigen 120 mm Lüfter Verwendung auf eigene Gefahr, der Designer übernimmt keine Haftung! Das abgebildet Blech (Edelstahl 1.5 mm) kann käuflich für 15€ + 5€ Versand innerhalb Deutschlands erworden...

Hi, I've got an i3 Mega UltraBase with TMC2208 drivers, and I designed a duct for it over on Thingiverse - https://www.thingiverse.com/thing:2773533. It worked okay until I upgraded to Marlin 1.1.8. With the new firmware, I was able to hit higher...

The air will then not directly exit the housing after the stepper drivers have been cooled but instead will be redirected to the board and chipset that would not be cooled with the original. I have also made it a bit slimmer in height at the end in...

For cooling the mainboard and the motor drivers. Bracket for 2x 40 mm fans e.g. Noctua NF-A4x10 FLX or NF-A4x20 FLX, also works with any other 40 mm fan. The holder can be attached to the two original mounting holes for the fan holder, you can also...

Dieser Stepper Driver Cooler wird mit einem 40x40mm Axiallüfter betrieben. Die Stützstruktur ist im Objekt integriert und muss nach dem drucken entfernt werden. Es ist kein Support via Slicer erforderlich! Ich habe es mit der Schrift nach unten...

This Stepper Driver Cooler runs on a powerful 40x40mm axial fan.\r\nIts built-in support structure gets automatically detached after printing, eliminating the need for any additional support through your slicing software!\r\nThe model was...

Holder for stepper driver fan on an Anycubic i3 Mega-S. ...The holder is for two 40mm fan.