anycubic direct drive 3d models
259002 3d models found related to anycubic direct drive.cults3d
Gantry for i3M gantry system. 50mm distance between rods. Super easy 3d printable, fast and light change, easy belt fix. Designed for e3d v6 heatsink. Super easy BL-touch mount, always fixed Z-offset, only 21mm Y-offset! ...50mm cooling fan, 30mm...
thingiverse
These are the components to convert a stock AnyCubic Chiron to a Direct Drive extruder, using the stock hot-end, extruder, and carriage components. This design also locates the extrude nozzle at "almost" stock location, so you can run stock Chiron...
thingiverse
This is a mod to convert the **Anycubic Vyper** to direct drive. The bracket weighs in at 40 grams (4 perimeters, 15% cubic infill, 7 top/bottom layers) and it's mounted to the existing carriage using stock hardware. An extension or a longer...
thingiverse
V3 updated here: https://www.thingiverse.com/thing:3751723 (Consider this one too) DONE***Working on a new duct and belt tensioner (Coming soon...) V1 Simple carriage for my Anycubic I3 with direct drive and clone extruder / V6 You will need: 3x IGUS...
thingiverse
I made this bracket to do a quick and dirty conversion to direct drive. ...Tuning retraction afterwards was a massive improvement in stringing
thingiverse
... When installing, remove the blue spacer between the carriage and the hot end wire plug. Cut a length of PTFE tubing to connect the extruder and the hot end. With the direct drive extruder installed you're still able to disconnect the hot end wires.
thingiverse
This is the quickest way to achieve a direct drive conversion. You'll have to remove the original casing and secure it with 4 small bolts and nuts, you will also require a 2" brass 1/8 nipple. Extending the extruder wire is necessary as well. I've...
thingiverse
I developed this light'ish weight direct drive extrusion system with the objective of matching or reducing the form factor of the stock print head assembly. I do a lot of sequential printing so I wanted minimal bulk around the nozzle. I also wanted...
cults3d
The direct drive mount is suitable for the original stepper including extruder Stepper motor is a >Nehma 17< Attention!!! Other stepper motors like Creality will not fit here Furthermore, cable extensions are needed to extend the lines. 4 times...
cults3d
Direct drive designs are now a dime a dozen, but this design has the edge: Simple design (Only one pressure part for the extruder holder with no need for support structures). Design is independent of other conversions (e.g., BLTouch extension or fan...
thingiverse
Direct Drive Designs gibt es inzwischen wie Sand am Meer, aber dieses Design hat die Vorteile: - Simples Design (Nur ein Druckteil für den Extruder-Halter ohne Notwendigkeit von Stützstrukturen) - Design ist unabhängig von anderen Umbauten (z.B. die...
thingiverse
Fits the newest version of the Anycubic Vyper ( i bought mine in April 2023). Might make the vyper a bit slower (50 mm/s with Linear Advance at 0.2K value) but no more stringing and TPU prints better then some printers do PLA. When you install the...
thingiverse
This is a direct drive conversion mount for the following printers: - Anycubic Kobra max - Anycubic Kobra plus - Anycubic Vyper Parts needed: Bondtech LGX extruder www.amazon.com/gp/product/B099NXJKPY Extension cable...
thingiverse
I'm putting together a remix of several different designs, kind of combining them into one unique creation. Huge thanks to all the folks out there who made these parts, if you spot something familiar, no worries, I appreciate your contribution! This...
thingiverse
An only one piece for direct drive mod for the anycubic Chiron. Part needed: -Trianglelab 5015 Fan, glued in place with on or 2 drop of cyano. -Trianglelab Highhall metal V6 hot end with its fan -Trinaglelab BMG extruder -Nema17 "pancake" motor"...
thingiverse
- buy a longer or extend the extrudermotor cable - place the cable in the cable duct (hotend, fan) - install the plate between the hotendhousing and frame - install the extruder motor and extruderbase on the new plate - shorten the bowdenpipe to the...
thingiverse
... # Features This little duct will force air strongly over the cooling fins and also to the left. There is a slight incline at the bottom that pushes air directly over the lowest fin, so there's no direct airflow on the heatblock.
thingiverse
This fan is a direct replacement for the one in the conversion kit, using the same screws and mounting holes as the bed level probe mount. It does not employ a magnet system, which I found to cause carriage crashes into the bed. My printed version...
thingiverse
This Thing is a Significant Upgrade for "Frozenrc's" Anycubic Chiron Direct Drive Conversion with Factory Extruder & Hotend ! Just an Add-On to his brilliant work, it enhances Airflow to the Hotend using a standard 40x40 Fan. This Fan Cage also...
thingiverse
This is my update version of this one: https://www.thingiverse.com/thing:3696097 With new duct and new adjustable belt/tensioner You will need: 3 IGUS RJ4JP-01-08 3x 40mm M3 screw for the motor/extruder 2x M3 bolt and screw for the belt holder 1x...
thingiverse
This creation was crafted using the versatile platform of Tinkercad. ...You can easily edit it online at https://www.tinkercad.com/things/4usGVu4eN1t
thingiverse
This is a direct drive mod for the Anycubic Chiron. It uses the original parts from the Chiron (extruder, stepper, fans and connector board). Additionally you need the printed parts and quite a lot M3x10 screws, M3 nuts and M3 square nuts. ... Have...
cults3d
I wasn't pleased with how the cooling fan was attached via magnets on https://www.thingiverse.com/thing:3586698, as it refused to sit straight up and I had an extra 5015 fan lying around, so I opted for a fan mount from...
thingiverse
I didn't appreciate how the cooling fan was attached via magnets on https://www.thingiverse.com/thing:3586698 - it refused to sit straight, and I had a spare 5015 fan just collecting dust, so I decided to swap out the fan mount from...
thingiverse
This is an Addon for https://www.thingiverse.com/thing:3586698 I watched a video from Phillips YouTube channel and wanted to add this feature to the awesome direct drive conversion. I added pictures for easy printing. Just cut some foam and squeeze...
thingiverse
... Features Cables experience less stress due to an improved bend radius. The chainguide runs on the backside, giving you space to work and keeping it out of your camera's line of sight. Big thanks go out to the creator of the direct drive conversion!
thingiverse
I really wanted to keep the good component cooling from the "Ultimate Extruder", so I use the suspension of the 5015 fan here:https://www.printables.com/de/model/231370-anycubic-chiron-ultimate-extruder And the component cooler without hanger tab...
thingiverse
This is a Direct Drive conversion using the factory Extruder, Hot End, Motor, Leveling probe, and breakout board that came with your Chiron. I designed this so you can continue to use the entire carriage as intended from the factory, along with the...
thingiverse
Remix of MT2s Design - made some room to add a 40mm hotendfan on the left and added something to tidy up the cables. Please don't mind my rough-around-the-edges approach in tinkercad... You can edit it here:...
thingiverse
Great and simple conversion design, but since I used PLA for my printer, I had issues with the extruder motor (gets warm+) starting to twist and warp the bracket over time. To try and prevent this, I made the top, left & right sides thicker and...