anycubic chiron simplify3d

Anycubic Chiron 80mm fan duct 80x80

Apparently it's a problem with many 4max pro that has a wrong thermistor I had to change the firmware to correct this problem: https://drucktipps3d.de/forum/topic/anycubic-4max-pro/?part=25 (dutch) (4MaxPro_fan_therm_V1.2.3.hex firmware) Portuguese:...

Apparently It's a Problem with Many 4max Pros that Have a Wrong Thermistor I Had to Change the Firmware to Correct This Problem: https://drucktipps3d.de/forum/topic/anycubic-4max-pro/?part=25 (4MaxPro_fan_therm_V1.2.3.hex Firmware) Portuguese...

Energieketten Halterung am Druckkopf für Anycubic Chiron Holder for the energy chain on the print head from Anycubic Chiron.

Retrofit Anycubic Chiron Tete USINE 2023 Pilotage par CAN BUS Makerbase MKS THR42 Board

I needed a lowe arm for the camera to my Anycubic Chiron.

This helps you to adjust your z-axis to the desired height. ... Suitable for Anycubic Chiron.

This is an adapter to mount the SKR 1.4 in an Anycubic Chiron

You can print a spare threading aid for the Anycubic Chiron extruder here.

desingt a adpter to fit a Lerdge Z board in to the original case from the Anycubic Chiron.

This is a replacement for the original cooling duct for the Anycubic Chiron. ...Designed in Fusion360 ,printed in Resin (recommended).

Needed a mount for the sonic pad sensor for my Anycubic Chiron. ...10Min later in fusion and this came out.

Update 10/3: Correct Fan Grill Uploaded Successfully. ... A Basic 40mm Fan Mount for the Anycubic Chiron.

Use standard 40mm fan for the Anycubic Chiron. ... For connecting 12 Volt fans you will need a 1W 150 Ohm resistor.

Anycubic Chiron Z-Axis Back Reinforcement BOM: Utilize two M10x750mm threaded rods, eight M10 nuts, and eight M5x60mm screws. ...No additional support is required.

This anchor attaches to the support of the Anycubic Chiron along with this low-friction filament holder https://www.thingiverse.com/thing:3015856

I have edited a good fan for Anycubic Chiron to lower a little bit fan dusk to blow air more precisely at prints

Mount for this Raspberry Pi Case https://princore.de/collections/stl-downloads/products/touchscreen-raspberry-pi-4# for my Anycubic Chiron

Just a piece of plastic that helps keep filament in place when You have a filament holder placed at the top rail of Your Anycubic Chiron.

Anycubic Chiron Extruder Threading Aid (Spare) Lost your Anycubic Chiron Extruder's threading aid? You can print a replacement right here. Note: The original text has been rewritten to maintain the same tone, voice, and phrasing while ensuring...

... for the strap for your x-axis. ... Settings: Printer brand: Anycubic  Printer: Large Size Chiron  Rafts: Doesn't Matter  Supports: Yes  Resolution: 0,2  Infill: 15  Filament brand: Material4Print  Filament color: neon orange  Filament material: PLA

This is a customized PSU cover remake tailored specifically to fit a 120mm fan on the Anycubic Chiron. I didn't design it myself and therefore don't deserve any credit for the work. ...A member of the International Chiron Support group on Facebook...

Reinforcement for the front and back 2020 profile of the Anycubic Chiron Material List: 8 uds -- Screw DIN912 M3*20 -- https://s.click.aliexpress.com/e/_AEPiVL 8 uds -- T-Nuts 20-M3 -- https://s.click.aliexpress.com/e/_9Jl8gt

The extra-long data cable for my Anycubic Chiron stays put with this clever holder. ...Installation is a breeze, and it works flawlessly, keeping the cable upright where it belongs.

Reinforcement for the front and back 2020 profile of the Anycubic Chiron ============================================================ Material List:...

a width adjustable filament spool holder for anycubic chiron. ... no srew or glue needed very easy to assemble no support need remember to calibrate the diameter of your printer https://youtu.be/cajgJnSKL_Y

This is an extended cable chain guide specifically designed for the xTremePower's Anycubic Chiron ultimate extruder module. Due to the stock chain stop no longer fitting, a new solution was developed. ...It functions effectively.

A design for saving and managing your cables for the x-axis and extruder (Anycubic Chiron). ... At the same time, it also serves as protection for the strap for your x-axis.

I just received my brand-new Anycubic Chiron and I've crafted this straightforward tutorial to prevent the X-Axis Cable Chain from colliding with the Hotend Connector as the carriage shifts towards the right.

The Anycubic Chiron Z-axis leadscrew fixer uses a robust 688ZZ bearing, paired with a sturdy 2M410 screw and two M4 2020 nuts to provide stable and precise motion control.