anycubic chiron simplify3d

This is a Vertical Cable Chain Mod for the AnyCubic Chiron the does NOT use any additional hardware, bolts, screws, nuts, etc... I completely remodeled each file using Solidworks, but did take inspiration from linked remix; I just couldnt find...

Semi-direct extrusion for Anycubic Chiron using the hotend mk8 / mk10. The same original X carriage is used, but the vice must be cut where the chain which carries the cable harness is screwed, so that the top of the carriage remains completely...

This is the siplest and most effective TITAN AERO VOLCANO conversion for the ANYCUBIC CHIRON. One design is without possibility to mount the filament sensor directly on the extruder and the other is with it. You can use the original screws and...

The AnyCubic Chiron Purge Bucket East Side Mounted is positioned over the stepper motor on the X Axis Bracket. Having the bucket on the right side of the bed made a bottom release door implausible, as debris would likely get into the control box...

Simple Upgrade Method for Original Chiron Spool Holder - 100mm Spool - 2.1 kg Capacity. ...Requires Only Two 608 Bearings (8x22x7mm) in Total.

I've modified the design of the Axis stabilizer for the Chiron Heatbed Stepper by adding a bearing to eliminate vibrations and install small rubber pads on the 2020 mounts. ...The result is that my Chiron is now entirely silent in operation.

... Gently tighten it The same with the other one Gently tighten all M4 screws Print Settings Printer Brand: Anycubic Printer: Large Size Chiron Rafts: No Supports: Yes Resolution: 0.3 Infill: 38 Filament: FDPlast PLA Black Category: 3D Printer Parts

This mount replaces the existing Chiron Filament Sensor, and allows you to use the trianglelabs.org filament sensor in line with the stock extruder. I needed this filament sensor because I primarily use Octoprint, and it doesn't recognize the...

If you ever wanted to use higher Velocities or Accelerations on your Chiron Printer, Use this Bracket, Use the Old Y Axis Stepper for your X Axis instead. ... The Only Downside: you loose 10mm of your Y Axis travel.

Upgrading my Chiron to direct drive requires several customized components, and relocating the x-axis home switch from the print head to the side is one of them. ... To accomplish this task, I designed a bracket specifically for this purpose.

Gently tighten it The same with the other one Gently tighten all M4 screws Print Settings Printer Brand: Anycubic Printer: Large Size Chiron Rafts: No Supports: Yes Resolution: 0.3 Infill: 38 Filament: FDPlast PLA Black Category: 3D Printer...

I came across a design on YouTube (https://www.youtube.com/channel/UCkXj9_80x1PquHxWZtT-6Hg check the videos about the Chiron - I'm not sure which one specifically it was...) a couple of months ago and decided to create my own feet for the Chiron...

This is a conversion kit to slap a SKR 2 into your AnyCubic Chiron (SKR 1.4 also probably works because they have the same mounting holes and similar layout). The Holes that need to be drilled into the side of the chassis (if you aren't just...

This is a conversion kit to slap a SKR 2 into your AnyCubic Chiron (SKR 1.4 also probably works because they have the same mounting holes and similar layout).The Holes that need to be drilled into the side of the chassis (if you aren't just planning...

This is a customized version of https://www.thingiverse.com/thing:3195516's "Chiron hotend housing and wire guide" by jangermann, modified to be compatible with the E3D V6 hotend.\r\n\r\nRevisions include:\r\nThe circuit board was relocated to the...

... unpleasant layer shift. This design on Tinkercad turned out to be quick and effortless. I mounted the Chiron using M5 8mm screws with hammer nuts for a secure hold. ... M5 8mm Screws: https://amzn.to/2Ezpzoo M5 Hammer Nuts: https://amzn.to/2Bo47yv

My Take on the LED Strip Holder for the Chiron - A Customized Solution. Attach 70cm LED Strips, consisting of two 35cm sections, using cable ties for a secure fit. ...Then, power them directly from the PSU with a Step-Down Converter.

I used this mount to fit a hemera onto my Chiron. ...&nbsp;Remixed from Tmaxx21 on thingiverse at: https://www.thingiverse.com/thing:4297095</p><p>&nbsp;I removed the part of the mount that holds the original I/0 board since I don't need...

This is a remix of pcr150 version found here https://www.thingiverse.com/thing:3339250. ...I made changes to allow it to fit my Chiron and not make contact with the captivated nut holding the x axis wheel carriage and clear the mounting plate.

... require tree supports to be printed. -Use Existing screws that come with BIQU and the screws that are removed from the Chiron Hot end for mounting new BIQU H2 Parts -Slot behind mount plate allows routing hotend fan and X axis limit switch wiring.

My Chiron's filettated bar is vibrating a lot... I tried to solve this problem by designing new angles that would replace the originals. I got the idea from this project: https://www.thingiverse.com/thing:3363460 but I reworked it entirely to suit my...

**Update: I've Enhanced the Duct for Improved Air Flow Focusing Towards the Nozzle** **Update 2: Eliminated Interference Between the Duct and Heat Block, Boosting Performance** I Designed This Upgrade to Optimize the Fan Duct on the Chiron, Resulting...

I only plan to use this design for small prints because the rod needs to be significantly extended to accommodate the 450mm build height of the Chiron. However, that's a project for another day. Update 30/05/2019: I discovered that trying to fix...

Wanted to add a GoPro mount to my Chiron, but just copying something was not as satisfying as expected... and designed this rod in Fusion360 - consists of 2 parts: fixation bracket extension rod The bracket can be fixed by a M4 screw to the Chiron...

So I basically re-created the existing Chiron cable mount under the heatbed, and spliced on a cable chain female connector to it (again, remixed from eth4ck1e's file), sizing it to fit my cable chain dimensions. This allowed me to connect the chain...

I was searching for a suitable place to mount the Palette2 on the Chiron since the extruder was converted to a DirectDrive a few months ago, but nothing seemed to fit well or guide filament properly. Since feeding material from the top appears to be...

If you've ever disassembled your Chiron, you'll have noticed that the mounts for the top of the z shafts are slightly loose (about 2mm play). This design is intended to replace them directly and is part of a major overhaul I'm working on. The design...

Servus,dachte mir, ich nehm es mal selber in die Hand und zeichne mir ein neues Housing für den Chiron, da das Alte nicht wirklich schön ist und es soweit nichts zu finden gibt. Es handelt sich hierbei nur um ein optisches Upgrade, das neue Housing...

I always got big problems with stringing on the Chiron. With "direct drive" these problems are gone. Important: You also can use the standard hotendhousing. Retractionsettings compared to each other: Before: (still much stringing) retraction -...

To connect the filament guide to the extruder, I utilized the bowden connector from the original extruder that comes bundled with the Chiron printer. The trianglelabs BMG extruder I used can be purchased through Aliexpress; simply click on the link...