anycubic chiron pla settings 3d models

I needed a lowe arm for the camera to my Anycubic Chiron.

This is an adapter to mount the SKR 1.4 in an Anycubic Chiron Print Settings Printer Brand: Anycubic Printer: Large Size Chiron Rafts: No Supports: No Resolution: 0.2 Infill: 40% Filament: any any any Post-Printing ============= Category: 3D...

This is a replacement for the original cooling duct for the Anycubic Chiron. ...Designed in Fusion360 ,printed in Resin (recommended).

Update 10/3: Correct Fan Grill Uploaded Successfully. ... A Basic 40mm Fan Mount for the Anycubic Chiron.

Needed a mount for the sonic pad sensor for my Anycubic Chiron. ...10Min later in fusion and this came out.

desingt a adpter to fit a Lerdge Z board in to the original case from the Anycubic Chiron.

... Anycubic Chiron/Mega Version 1.3 Wiring is needed and due to the bulkiness of the BIQU H2 auto level system may need to be relocated. Please contact us if you have any issues. ...Check out our mount for the BIQU H2 and the Chiron in our downloads.

Remix of thing:2430477 and thing:3156323 for mounting an extruded aluminium LED light bar to my Anycubic Chiron. This is mounted just above bed height and will help highlight a dusty/dirty bed and to see if the first layer is adhering well. Mixed...

An only one piece for direct drive mod for the anycubic Chiron. Part needed: -Trianglelab 5015 Fan, glued in place with on or 2 drop of cyano. -Trianglelab Highhall metal V6 hot end with its fan -Trinaglelab BMG extruder -Nema17 "pancake" motor"...

Just a piece of plastic that helps keep filament in place when You have a filament holder placed at the top rail of Your Anycubic Chiron.

Anycubic Chiron Z-Axis Back Reinforcement BOM: Utilize two M10x750mm threaded rods, eight M10 nuts, and eight M5x60mm screws. ...No additional support is required.

This anchor attaches to the support of the Anycubic Chiron along with this low-friction filament holder https://www.thingiverse.com/thing:3015856

Use standard 40mm fan for the Anycubic Chiron. ... For connecting 12 Volt fans you will need a 1W 150 Ohm resistor.

Mount for this Raspberry Pi Case https://princore.de/collections/stl-downloads/products/touchscreen-raspberry-pi-4# for my Anycubic Chiron

I have edited a good fan for Anycubic Chiron to lower a little bit fan dusk to blow air more precisely at prints

Anycubic Chiron Extruder Threading Aid (Spare) Lost your Anycubic Chiron Extruder's threading aid? You can print a replacement right here. Note: The original text has been rewritten to maintain the same tone, voice, and phrasing while ensuring...

Adjustable X Carriage for Anycubic Chiron. Phaetus Dragon is 5mm too fat, and 10mm too short for the tallest bed setting and my fans were lower than the nozzle protruded. ...being adjustable; I can both reposition the hotend with relative ease, AND not...

This remix updates the mounting bracket of the "Filler Spool Holder" for the Anycubic Chiron. I've used these on my Anycubic Mega (I did that remix too) and both my Ender 3's. It reduces drag on filament feeding, especially on the Chiron with its...

This is a customized PSU cover remake tailored specifically to fit a 120mm fan on the Anycubic Chiron. I didn't design it myself and therefore don't deserve any credit for the work. ...A member of the International Chiron Support group on Facebook...

*Palette 2 Wall Mount Bracket.stp is design and (c) of MosaicMfG - see https://www.thingiverse.com/thing:3065172 for details* Print Settings Printer Brand: Anycubic Printer: Large Size Chiron Rafts: No Supports: No Resolution: 0,2mm layer height...

A design for saving and managing your cables for the x-axis and extruder (Anycubic Chiron). ... At the same time, it also serves as protection for the strap for your x-axis.

The Anycubic Chiron Z-axis leadscrew fixer uses a robust 688ZZ bearing, paired with a sturdy 2M410 screw and two M4 2020 nuts to provide stable and precise motion control.

a width adjustable filament spool holder for anycubic chiron. ... no srew or glue needed very easy to assemble no support need remember to calibrate the diameter of your printer https://youtu.be/cajgJnSKL_Y

This is an extended cable chain guide specifically designed for the xTremePower's Anycubic Chiron ultimate extruder module. Due to the stock chain stop no longer fitting, a new solution was developed. ...It functions effectively.

Reinforcement for the front and back 2020 profile of the Anycubic Chiron ============================================================ Material List:...

Reinforcement for the front and back 2020 profile of the Anycubic Chiron Material List: 8 uds -- Screw DIN912 M3*20 -- https://s.click.aliexpress.com/e/_AEPiVL 8 uds -- T-Nuts 20-M3 -- https://s.click.aliexpress.com/e/_9Jl8gt

I just received my brand-new Anycubic Chiron and I've crafted this straightforward tutorial to prevent the X-Axis Cable Chain from colliding with the Hotend Connector as the carriage shifts towards the right.

The extra-long data cable for my Anycubic Chiron stays put with this clever holder. ...Installation is a breeze, and it works flawlessly, keeping the cable upright where it belongs.

This is a set of parts to accomodate installing an E3D Volcano upgrade on an Anycubic Chiron. When upgrading the hotend, it becomes taller, so without modifications: - the nozzle touches the platform before the Z endstops trigger - the blower is too...

In the original Anycubic Chiron 3D printer setup, the x-axis cable chain runs horizontally. This leads to extreme bending of wires and increases the likelihood of them snapping after hundreds of hours of printing. The included support set features...