anycubic chiron fan replacement 3d models

I designed a TPU base for this version of the Anycubic Chiron feetV2, which can be found at https://www.thingiverse.com/thing:3560291. To assemble it, simply change the orientation so that the base lies flat on the build plate. ...After printing is...

There was no good way to attach the Mosaic Palette 3 Pro filament clip to the Anycubic Chiron, so I measured and modeled this holder that goes over the filament sensor. It is attached right now with twist ties, will upgrade to a sturdier connection...

Works with Adrian Studer's stabilizer: https://www.thingiverse.com/thing:4833402 Allows you to use a big spool with your Anycubic Chiron and not waste a ton of space. I am using direct drive BIQU H2. ...This is why there is no extruder on this side.

Hey, This is a sensor mount for the Auto-Level sensor, installed on the side of the Anycubic Chiron. Use a M5 x 8mm screw and a t-nut to secure the mount at any point along the 4020 extrusion. ...I have adjusted the X-Axis mounting point approximately...

Hello all, Here are my optimization designs for my new Anycubic Chiron. I adore this printer, but I have reservations about the extruder and cooler block. So, I decided to modify them entirely. I created a complete block that you can use with your...

Biqu H2 Mount + cover for Bl-Touch for AnyCubic Chiron It is a design that hide cables and have a nice finish. I will make an instruction to mount the cables behind the extruder. It is not really complicated to hide the cables. Motor connector...

Wanted to have a lettering for my Anycubic Chiron, unfortunately I have not found on the Internet. So I sat down at the PC and created a lettering myself and printed it in two colors on my Chiron - of course, the lettering can also be printed in one...

A sturdy enclosure bracket for the Anycubic Chiron 3D printer holds thin foldable plastic in place. This design is similar to a previous one created for the Anycubic i3 MEGA, but it's specifically tailored for the Chiron model. The Chiron has a...

There was no good way to attach the Mosaic Palette 3 Pro filament clip to the Anycubic Chiron, so I measured and modeled this holder that goes over the filament sensor. It is attached right now with twist ties, will upgrade to a sturdier connection...

Da das Kabel beim Anycubic Chiron leider nach einer weile einen Bruch erleidet, kann dies durch das anbringen der Schleppkette verhindert werden. Die beiden Kabel Phase und Null (Schwarz und Rot) die am Heizbett angelötet sind, habe ich entlötet und...

Human: adapter needed to install Creality mk8 hotend in Anycubic Chiron. Completely compatible with height sensor and original box, also works with this box design https://www.thingiverse.com/thing:3195516 No modifications are required for car X, V5...

Damper for Anycubic Chiron Significantly reduced vibration transmission from printer to table. During the printing, the printer wobbles about 1-2mm in the y-axis. This has no effect on the print quality except when printing thin bars When the...

The reason for this is Anycubic using subpar quality cables and winding them around one of the coils of the heated bed, creating an extremely narrow curve. The thermistor cable doesn't appear to be much better in terms of quality. I suggest replacing...

Hello everyone, Here are the optimization designs for my new Anycubic Chiron extruder. I love this printer, but I'm not a fan of the extruder and cooler block. So, I decided to completely modify it. I designed this entire block from scratch. You'll...

The Anycubic Chiron is a 3D printer that features an innovative Y-axis belt tensioner, designed to provide smooth and precise movement of the print bed. This mechanism allows for optimal alignment and tensioning of the belt, ensuring accurate and...

You can find his firmware updates on GitHub at https://github.com/zombu2/Marlin-2.0-Anycubic-Chiron and join our Discord community at https://discord.gg/RrfEcps to discuss 3D printing topics. To use the sensor with the original Trigorilla board,...

... brace. ... Support structure for Chiron requires additional reinforcement with a screen backplate. The setup necessitates T-Nuts and screws. ... Two 8mm x 22mm x 7mm bearings are required, along with threaded rods M10 featuring bolts and washers.

Para que quede la boquilla a la misma altura que la original, la parte superior del soporte debe estar a unos 6mm del borde del carro X adapter to install a Creality mk8 hotend in the Anycubic Chiron. Fully compatible with the height sensor and...

... my project below. Please check out my Anycubic Chiron comprehensive upgrades project at https://www.thingiverse.com/thing:3903504 - a compilation of files from other projects that I have improved or deemed critical for the improvement of the Chiron.

Remixed from thing 4699265 Modified to be able to mount it on the Anycubic Chiron printer. It use the original level sensor and original end-stop microswitch. You need the CR10S carriage ( https://urly.it/3c92z ) and all voron Afterburner needs...

I was searching for a good-looking and functional stabilizer for the z-axis of my Chiron. Finally I desided to design it by myself. Here is my solution for the z-axis of the Anycubic Chrion. You're loosing no printing height and it also fixes the...

I designed an extruder plate to adapt the Bear extruder v0.7 to the Anycubic Chiron with a 3.5:1 gearbox. This design could potentially be used for mounting any MK3S extruder, but I chose these specific options. All credit goes to Grégoire Saunier...

I decided to change the supplied titan extruder on my Anycubic Chiron to a dual geared extruder. After researching a number of third party designs I bought a relatively cheap but seemingly well made option on Aliexpress. To make this extruder work...

Para que quede la boquilla a la misma altura que la original, la parte superior del soporte debe estar a unos 6mm del borde del carro X adapter to install a Creality mk8 hotend in the Anycubic Chiron. Fully compatible with the height sensor and...

the fan ducts are remixes from (https://www.thingiverse.com/thing:4918636) (https://www.thingiverse.com/thing:4931226) splitted the part cooling duct for easy print & clue. the stepper wiring must be changed. stock autolevel sensor mount added ...

the fan ducts are remixes from (https://www.thingiverse.com/thing:4918636) (https://www.thingiverse.com/thing:4931226) splitted the part cooling duct for easy print & clue. the stepper wiring must be changed. stock autolevel sensor mount added...

Totalmente compatible con el sensor de altura y caja original, también es compatible con éste diseño de caja https://www.thingiverse.com/thing:3195516 No es necesario hacer ninguna modificación a carro X, se usan los agujeros del soporte del V5...

We're glad you asked about our experience with the Anycubic Chiron. This printer offers impressive value for its price, but some parts are a bit flimsy. After conducting thorough testing, we pinpointed a major issue: problems with the Y-Stepper...

This thing is a custom designed direct extruder holder part for anycubic chiron. Available in two versions. With or without filament guide. The available body1.stl is a filament guide to the original place of extruder. Few things you need for the...

The Anycubic Chiron Filament Holder has a major flaw - the original metal sheet holder is painted, making it extremely difficult to unroll the roll. This causes the stepper motor to waste a significant amount of energy. We designed a new holder with...