anycubic chiron extruder 3d models

This is a conversion kit to slap a SKR 2 into your AnyCubic Chiron (SKR 1.4 also probably works because they have the same mounting holes and similar layout).The Holes that need to be drilled into the side of the chassis (if you aren't just planning...

This is a conversion kit to slap a SKR 2 into your AnyCubic Chiron (SKR 1.4 also probably works because they have the same mounting holes and similar layout). The Holes that need to be drilled into the side of the chassis (if you aren't just...

... unpleasant layer shift. This design on Tinkercad turned out to be quick and effortless. I mounted the Chiron using M5 8mm screws with hammer nuts for a secure hold. ... M5 8mm Screws: https://amzn.to/2Ezpzoo M5 Hammer Nuts: https://amzn.to/2Bo47yv

This is a customized version of https://www.thingiverse.com/thing:3195516's "Chiron hotend housing and wire guide" by jangermann, modified to be compatible with the E3D V6 hotend.\r\n\r\nRevisions include:\r\nThe circuit board was relocated to the...

This is a remix of pcr150 version found here https://www.thingiverse.com/thing:3339250. ...I made changes to allow it to fit my Chiron and not make contact with the captivated nut holding the x axis wheel carriage and clear the mounting plate.

My Take on the LED Strip Holder for the Chiron - A Customized Solution. Attach 70cm LED Strips, consisting of two 35cm sections, using cable ties for a secure fit. ...Then, power them directly from the PSU with a Step-Down Converter.

I used this mount to fit a hemera onto my Chiron. ...&nbsp;Remixed from Tmaxx21 on thingiverse at: https://www.thingiverse.com/thing:4297095</p><p>&nbsp;I removed the part of the mount that holds the original I/0 board since I don't need...

**Update: I've Enhanced the Duct for Improved Air Flow Focusing Towards the Nozzle** **Update 2: Eliminated Interference Between the Duct and Heat Block, Boosting Performance** I Designed This Upgrade to Optimize the Fan Duct on the Chiron, Resulting...

... require tree supports to be printed. -Use Existing screws that come with BIQU and the screws that are removed from the Chiron Hot end for mounting new BIQU H2 Parts -Slot behind mount plate allows routing hotend fan and X axis limit switch wiring.

My Chiron's filettated bar is vibrating a lot... I tried to solve this problem by designing new angles that would replace the originals. I got the idea from this project: https://www.thingiverse.com/thing:3363460 but I reworked it entirely to suit my...

I only plan to use this design for small prints because the rod needs to be significantly extended to accommodate the 450mm build height of the Chiron. However, that's a project for another day. Update 30/05/2019: I discovered that trying to fix...

Wanted to add a GoPro mount to my Chiron, but just copying something was not as satisfying as expected... and designed this rod in Fusion360 - consists of 2 parts: fixation bracket extension rod The bracket can be fixed by a M4 screw to the Chiron...

So I basically re-created the existing Chiron cable mount under the heatbed, and spliced on a cable chain female connector to it (again, remixed from eth4ck1e's file), sizing it to fit my cable chain dimensions. This allowed me to connect the chain...

If you've ever disassembled your Chiron, you'll have noticed that the mounts for the top of the z shafts are slightly loose (about 2mm play). This design is intended to replace them directly and is part of a major overhaul I'm working on. The design...

Servus,dachte mir, ich nehm es mal selber in die Hand und zeichne mir ein neues Housing für den Chiron, da das Alte nicht wirklich schön ist und es soweit nichts zu finden gibt. Es handelt sich hierbei nur um ein optisches Upgrade, das neue Housing...

Use standard 20x10 cable chain. ... Unfortunately, you will have to extend extruder & X motor cables. ... Udpate 22.01.2023: stronger bottom mount + added bed for the chain.

I think this is everything needed, and I added fan ducts as well, but they are not my design - only the mount for them I added a place for the Chiron terminal block. Newest Version is the V4.1 - and it's my final one! Check it out.. I have printed...

This is a drop-in improvement for the Anicubic Chiron Y-Axis carriage. I decided to design a roller wheel-to-linear axis modification that did not require the changing of end stop positions, packing the heated print bed or reduced the available...

I've removed and rotated the ends of the chain and the whole chain so many times, I don't remember what should specifically be changed, but the chain can't go behind anymore due to the Extruder motor on the back.OMG Extruder:...

This reverse bowden is used to screw it to the extruder support with 2 M3 screws, and a PC4 M10 through fitting, in order to better guide the filament to direct systems. ... Este reverse bowden sirve para atornillarlo al soporte del extrusor con 2...

This reverse bowden is used to screw it to the extruder support with 2 M3 screws, and a PC4 M10 through fitting, in order to better guide the filament to direct systems. ... Este reverse bowden sirve para atornillarlo al soporte del extrusor con 2...

Saw this design on a YouTube channel (https://www.youtube.com/channel/UCkXj9_80x1PquHxWZtT-6Hg check the videos abtout the Chiron - cannot remember the exact one...) a couple of months ago and decided to design the feet myself to get some more...

Great and simple conversion design, but since I used PLA for my printer, I had issues with the extruder motor (gets warm+) starting to twist and warp the bracket over time. To try and prevent this, I made the top, left & right sides thicker and...

... 2 holes for a zip tie to keep cables in place, and add clearance for the cables. - Mount on top stepper motor screws instead of bottom, as is it protect the pulley in the same time Extruder and X axis cables must be about 10 cm longer. ... Enjoy !

EDIT: DOES NOT WORK NEED COMPLETE OVERHAUL OF THE RIGHT PART'S EXTRUDER AT MAXIMUM Z HEIGHT No drilling is needed. Easy installation comes with a straightforward mount that uses the stock holes under the small protective plastic part, which must be...

... tie to keep cables organized and provided clearance for them. Additionally, I mounted the stepper motor screws on top instead of the bottom, which protects the pulley at the same time. The extruder and X-axis cables need to be about 10 cm longer.

I have installed the BMG "upgrade" to a direct-drive extruder, but find I still need to remove it from the gantry plate when I block the unit. The X axis micro switch is on this assemble and the wiring gets in the way. A replacement left-hand...

Anycubic Extruder Knob

Notice: The distance between the holes for the sensor is only valid for the Original Anycubic Chiron Sensor. This Holder has to be mounted on the original angle plate (see picture). You have to drill two 3mm holes into the angle plate. Infos: ...

A basic extruder bracket that fits the Anycubic Kobra Standard model.Prints well facing down without the need of supports.