anycubic bed 3d models

Bed grip for Anycubic Kobra 2 Fits perfectly and can be hidden.

This is a Bed Alignment guide for the AnyCubic Kobra 2 Plus.May Damage Foam Under Print Bedprinted using Prusa Slicer:No Raft3x Skirt5% infill

On the Anycubic i3 Mega/Mega-S, the Heated Bed Unit is attached to the Ultra-glass unit via sticky tape. However, the aluminum heated bed and glass ultra-base should not be tightly attached, or they will bend due to their different shrinkage rates.

Note: due to the general abandonment of Thingiverse and recent security issues, I've moved my designs to the Prusa Printers site: https://www.prusaprinters.org/social/171511-djos_1475/prints...

Anycubic Mega Zero v1.0 Bed Thumbwheels are a remix - I made these taller with inset M3 nuts specifically for Mega Zero v1.0's with Heated Bed upgrades that larger than the stock bed (via adapters). I recommend these be printed in ABS+ due to the...

Bed level test...

In case you need to lift or move the bed of your Anycubic i3 Mega, refrain from using its height-adjusting knobs - this could result in your bed losing its adjusted position along the Z-axis. I've personally experienced this issue once before. It...

Remove the printed part, and drill out the hole with a 3,2mm drill Remove the M3 nuts and washers from left or right side of the ultrabase bed Put an M3x30mm countersunk screw in the center hole of the printed part Now attach the printed part to the...

I used Onshape for the original drawing, so if you want to do any adjustments to the original drawings you can find them with this link: https://cad.onshape.com/documents/ec0d91ee24f4f9e61d9240a1/w/4435b4504876d0c24c086cef/e/5444b0fb228acd7783f3b459...

This is a replacement carriage for the Anycubic i3 Mega Y plate. I encountered leveling issues with the metal plate and designed a five-part solution to address this problem in areas where printing quality was compromised. ...The design was created...

I wanted a part for my Wash and Curing station from Anycubic. I dont like the original Cage for the Washing part, so i build a new one. Build with your slicer, but without Top and Botton Part, Select Gyroid Infill for good stiring. ...10% should be...

If you want to make any adjustments to the original drawings, you can find them at this link: https://cad.onshape.com/documents/ec0d91ee24f4f9e61d9240a1/w/4435b4504876d0c24c086cef/e/5444b0fb228acd7783f3b459 The Anycubic Kossel Linear Plus has a 240mm...

... faster print with less support. Back of camera case didn't fit either, had to use file and knife. Therefore removed some material. Update 3/11/19 Added hole to the tilt arm for an M2 skrew to reduce the wobbling of the camera when the bed moves.

I'm trying to assemble a Clearminds bed mount, but it won't fit on my bed because it's only 4 mm thick. To speed up printing with less support material, I've shifted the cable supports. Unfortunately, the back of my camera case also doesn't fit...

I wanted a part for my Wash and Curing station from Anycubic. I dont like the original Cage for the Washing part, so i build a new one.</p> <p>Build with your slicer, but without Top and Botton Part, Select Gyroid Infill for good stiring. ...10% should...

================================================== The goal is to create a corner cover, along with a heated bed holder and corner support, all in one piece - 3 in 1. Modified: 2018-04-06. The corner size has been repaired, and the bed holder...

One of the things I miss about the original photon was how easy you could rotate the bed by 90 degrees after printing to allow hollow parts to drain fully, this design achieves the same thing but at a angle of 88 degrees to keep the top of the build...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

My settings for optimal printing performance include: Extruder temperature: 215°C Initial layer temperature: 200°C Heatbed temperature: 75°C Initial layer heatbed temperature: 60°C Travel speed: 15 mm/s Skirt layers: 3-4 To use this file, simply...

I was searching high and low for a sturdy mount to attach my Insta360 ONE R (GoPro-style mount) to my print bed, but all I could find were flimsy options that would likely flex or fall off during printing. So, I took matters into my own hands and...

Another precision leveling system for your 3D printer. To install it, you'll need three sturdy DIN-933 screws. I took a clever approach by crafting the nut and locknut from durable stainless steel. However, in reality, they're even more resilient...

7x7 mm chain used. Mounting screwed to the bearing bolts. The cables of the original length do not need to be extended. For mounting in the housing, you can drill an additional hole or glue the chain on a double-sided tape or glue. ... Resolution 0.18 ...

Anycubic Wash & Cure Replacement BED and Bed Cover Anycubic W&C comes with an Acrylic bed and if not careful it can get damaged easily. to eliminate the issue you can either print the cover for the BED in PLA ( PLA do not react with Resin) ) to...

Designed Specifically for Use with M3 Screws Key Features Include: -Upgraded Version - MK2 -Equipped with Strategically Placed Holes for Secure Zip Tie Attachment

Customized version of https://www.thingiverse.com/thing:34558 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=34558

Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663

This is a remix of some models found in several 3d websites, but designed from scratch in Freecad.The model was resized so that it fits very tightly to the original knobs, and assembly is only possible by tightening the two pieces in a vice.I got...